Advertisement
Available languages
Available languages
Supplier's Declaration of Conformity
47 CFR § 2.1077 Compliance Information
Unique Identifier: DW0250
Responsible Party – U.S. Contact Information
DEWALT
701 East Joppa Road
Towson, Maryland 21286
www.DEWALT.com
FCC Statement
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a different circuit (not the circuit to
which the receiver is connected).
- Consult the dealer or an experienced radio/TV technician for help.
Canada, Industry Canada (IC) Notices
This Device complies with Industry Canada License-exempt RSS
standard(s). Operation is subject to the following two conditions: 1) this
device may not cause interference, and 2) this device must accept any
interference, including interference that may cause undesired operation of
the device.
Under Industry Canada regulations, this radio transmitter may only operate
using an antenna of a type and maximum (or lesser) gain approved for
the transmitter by Industry Canada. To reduce potential radio interference
to other users, the antenna type and its gain should be so chosen that
the equivalent isotropically radiated power (e.i.r.p.) is not more than that
necessary for successful communication.
Battery Safety
WARNING:
Batteries can explode, or leak, and can cause injury or fire. To
reduce this risk:
• Carefully follow all instructions and warnings on the battery label and
package.
• Always insert batteries correctly with regard to polarity (+ and –), as
marked on the battery and the equipment.
• Do not short battery terminals.
• Do not charge disposable batteries.
• Do not mix old and new batteries. Replace all batteries at the same time
with new batteries of the same brand and type.
• Remove dead batteries immediately and dispose of per local codes.
• Do not dispose of batteries in fire.
• Keep batteries out of reach of children.
DEWALT MPP1 STUD SENSOR - DW0250 - User Manual - MAY 2019.indd 7
Installing AAA Batteries
Load two new AAA batteries in the DW0250 stud sensor.
On the bottom of the stud sensor, lift up the latch (Figure
1.
unlock the battery compartment cover.
Move the cover upward (Figure
2.
from the stud sensor.
Insert two new, high-quality AAA batteries, making sure to position the
3.
- and + ends of each battery as noted inside the battery compartment
(Figure
).
B 3
Place the cover back on the stud sensor (Figure
4.
• Insert the two pins at the top of the cover into the holes near the top of
the battery compartment.
• Slowly lower the cover and press down until the latch locks securely
on the stud sensor.
Press
(Figure
) to test the stud sensor.
5.
A 3
• The stud sensor should sound one short beep.The Power
should turn on. All the other LEDs should illuminate for a second and
then turn off.
• Whenever you press
, the green Power
to indicate that the batteries are good. If this LED blinks or does not
illuminate, change the batteries.
Using the Stud Sensor
The DW0250 stud sensor will help you find wood or metal studs or AC
voltage behind drywall.
• The stud sensor will detect wood studs through up to 1" (25mm) thick
drywall, and metal studs and AC voltage through up to 1.5" (38mm) thick
drywall.
• When AC voltage is found, the stud sensor will sound short (alternating)
beeps and light the AC LED (Figure
• When the center of a stud is found, the stud sensor will sound one longer
(constant) beep and light the center LEDs (Figure
• When live AC and the center of a stud are both found, the stud sensor will
alternate between the long and short beeps, and light the center LEDs
and the AC LED.
Finding a Stud
To hold the stud sensor, place your thumb on one side of the stud
1.
sensor, your pointer finger and your palm over the center of the stud
sensor, and the rest of your fingers on the same hand on the other side
of the stud sensor (Figure
C 1
Gently place the stud sensor flat against the wall and parallel to a door
2.
or window on the same wall, which gives you an indication of how the
studs are positioned behind the wall (Figure
Without moving the stud sensor, use your pointer finger to press and
3.
hold
(Figure
). WAIT 1 sec until all the LEDs (except the
A 3
Power
LED) turn off.
While still pressing
, SLOWLY move the stud sensor to the left or
4.
the right on the wall.
) to
B 1
) and remove it once it separates
B 2
).
B 4
LED
LED should illuminate
).
A 5
).
A 4
).
).
C 2
5/21/2019 3:35:26 PM
E
7
Advertisement
