Power Source; Basic Setup; Auto Setup; Setting The Language - Toshiba 19LV505 Service Manual

Connections Connections
Connecting to optional equipment (Continued)/

Power source

Connecting to a PC (Personal Computer)
Before you connect this TV/DVD to your PC, change the adjustment of your PC's Resolution and Refresh rate (60 Hz).
Connect one end of a (male to male) VGA cable to the video card of the computer and the other end to the VGA connector PC
MONITOR on the rear of the TV/DVD. Attach the connectors firmly with the screws on the plug. In case of a Multimedia computer,
connect the audio cord to the audio output of your Multimedia computer and to the AUDIO connector of the PC AUDIO IN jack of
the TV/DVD.
Select "PC" by pressing INPUT repeatedly.
Switch on the computer. The TV/DVD can operate as the computer monitor
Back side
To PC AUDIO IN jack
Audio cord (not supplied)
To PC
MONITOR IN
VGA cable (not supplied)
Note:
• The on-screen displays will have a different appearance in PC mode than in TV mode.
• If there is no video signal from the PC when the unit is in PC mode, "No signal" will appear on the TV/DVD-screen.
Power source
To use AC power source
1. Connect the AC cord plug into this TV/DVD's AC INPUT jack.
2. Connect the AC cord into an AC outlet.
Note:
• Never connect the AC line cord plug to other than the specified voltage (120V 60Hz). Use the attached power cord only.
• If the polarized AC cord does not fit into a non-polarized AC outlet, do not attempt to file or cut the blade. It is the user's
responsibility to have an electrician replace the obsolete outlet.
• If you cause a static discharge when touching the unit and the unit fails to function, simply unplug the unit from the AC outlet
and plug it back in. The unit should return to normal operation.
• If the AC cord plug is plugged in for the first time, wait for approx. 5 seconds before pressing POWER.
20
J50S0101A.indb 20

Basic setup

Setting the language

This TV/DVD can display the on screen language in English, French or
Spanish.
Select the language you prefer fi rst, then proceed with the other menu options.
Setting the language
1 To turn on the TV/DVD, press POWER.
• POWER indicator on the front of the unit
changes green. It may take approx. 10 seconds
for a picture to appear on screen.
2 Press MENU. The TV menu screen will
appear. Press • • or • • to select "Setup", then
press • • or ENTER.
Main Menu
Picture
Audio
Channel
Lock
Setup
: Select ENTER:Set
3 Press • • or • • to select "Language".
Setup
Closed Caption >>
Language English
Video Label >>
Backlight 16
Auto Shut Off Off
Aspect On
Reset >>
: Select : Adjust
22
J50S0101A.indb 22
Monitor Display modes
MODE Resolution Refresh rate
VGA 640x480 60Hz
VGA 720x400 70Hz
SVGA 800x600 60Hz
XGA 1024x768 60Hz
WXGA 1280x768 60Hz
WXGA 1280x720 60Hz
WXGA 1360x768 60Hz
To return to normal mode
Press INPUT again.
Illustration of
19LV505
AC Outlet
Wider Hole
and Blade
AC 120V, 60Hz
AC cord (supplied)
1/19/08 2:41:22 PM
POWER
MENU
ENTER
/ / /
EXIT/CANCEL
4 Press • • or • • to select the desired language:
English, French (Français) or Spanish
(Español).
5 Press EXIT/CANCEL to return to the normal
screen.
Note:
• If the unit does not operate properly, or No key
operation (by the unit and/or the remote control):
Static electricity, etc., may affect the TV/DVD's
operation. In such case, disconnect the AC cord once,
then connect it again.
• If no buttons are pressed for more than about 60
seconds, the MENU screen will return to normal
operation automatically.
• The TV section has its own menu and the DVD
section also has its own menu .
60
1/19/08 2:41:24 PM
Basic setup

Auto Setup

The Auto Setup function helps to install your TV/DVD easily.
It leads you the Language selection, Air/Cable selection and Automatic
channel search.
IMPORTANT: Make sure that the antenna or cable TV system
connection is made!
Auto Setup
1 To turn on the TV/DVD, press POWER.
• POWER indicator on the front of the unit
changes green. It may take approx. 10 seconds
for a picture to appear on screen.
2 Auto Setup menu appears on the screen.
Press • • or • • to select "Language", then
press • • or • • to select your desired language.
Auto Setup
Language English
Signal Type Cable
Automatic Search Start
: Select : Adjust
3 Press • • or • • to select "Signal Type", then
press • • or • • to select "Air" or "Cable".
Auto Setup
Language English
Signal Type Cable
Automatic Search Start
: Select : Adjust
Air - VHF/UHF channels
Cable - Cable TV channels
4
Press • • or • • to select "Automatic Search",
then press ENTER.
Auto Setup
Language English
Signal Type Cable
Automatic Search Start
: Select : Adjust
J50S0101A.indb 21

To memorize channels

This TV/DVD is equipped with a channel memory feature which allows channels
to skip up or down to the next channel set into memory, skipping over unwanted
channels. Before selecting channels, they must be programmed into the
TV/DVD•• s memory. To use this TV/DVD with an antenna, set the Tuning Band
menu option to the Air mode. When shipped from the factory, this menu option
is in the Cable mode.
Air/Cable selection
1 Press MENU in the TV mode. The TV menu
screen will appear. Press • • or • • to select
"Channel", then press • • or ENTER.
Main Menu
Picture
Audio
Channel
Lock
Setup
: Select ENTER:Set
2 Press • • or • • to select "Auto Ch Memory",
then press • • or ENTER.
Channel
Add/Delete >>
Auto Ch Memory >>
Ch Label >>
3 Press • • or • • to select "Signal Type".
Auto Ch Memory
Signal Type Cable
Automatic Search Start
4 Press • • or • • to select "Air" or "Cable".
Auto Ch Memory
Signal Type Air
Automatic Search Start
Air - VHF/UHF channels
Cable - Cable TV channels
5 Press EXIT/CANCEL to return to the normal
screen.
J50S0101A.indb 23
POWER
ENTER
/ / /
EXIT/CANCEL
5 Now the "Automatic Search" starts.
Auto Setup
Language English
Signal Type Cable
Automatic Search Start
Analog Channel Found : 0
Digtal Channel Found :
0
EXIT : End
• If you press EXIT/CANCEL, the Automatic
Search stops and changes to the TV screen.
• After the starting setup is completed, the TV
channel appears on the screen.
Note:
• The Auto Setup function will work only when you
press POWER for the first time.
• The process of "Automatic Search" may take 15 to
30 minutes to complete, depending on your regional
cable service.
21
1/19/08 2:41:23 PM
ENTER
/ / /
EXIT/CANCEL
MENU
Automatic search
1 Press MENU in the TV mode. The TV menu
screen will appear. Press • • or • • to select
"Channel", then press • • or ENTER.
Main Menu
Picture
Audio
Channel
Lock
Setup
: Select ENTER:Set
2 Press • • or • • to select "Auto Ch Memory",
then press • • or ENTER.
Channel
Add/Delete >>
Auto Ch Memory >>
Ch Label >>
: Select ENTER:Set
3 Press • • or • • to select "Automatic Search",
then press ENTER.
Auto Ch Memory
Signal Type Cable
Automatic Search Stop
Analog Channel Found : 0
Digital Channel Found : 0
: Select ENTER:Cancel
4 The TV/DVD will begin memorizing all the
channels available in your area.
23
1/19/08 2:41:26 PM