Sony ILCE-6000 Service Manual page 14

Ver. 1.3 2014.11
The changed portions from
Ver. 1.2 are shown in blue.
2-1-5. IMAGER BLOCK SECTION
ns: not supplied
212
Mount Section
(See page 2-10)
206
(Note 2, 3)
207
(Note 2, 3)
208
(Note 2, 3)
4 211
(including CP6001 (CMOS imager)
and IS-095 complete board)
(Note 4)
Ref. No. Part No. Description
201 4-530-608-01 FRONT FRAME (775)
202 1-880-964-11 IS-076 FLEXIBLE BOARD
203 1-880-963-11 IS-075 FLEXIBLE BOARD
204 4-474-412-01 IM HEAT SINK (2000)
205 4-487-617-01 IM RADIATION SHEET (2000)
* 206 Selection Parts IM WASHER (A), ADJUST (Note 2, 3)
* 207 Selection Parts IM WASHER (B), ADJUST (Note 2, 3)
* 208 Selection Parts IM WASHER (C), ADJUST (Note 2, 3)
209 A-1987-432-A MB CHARGE UNIT (2000)
210 1-487-619-31 SHUTTER UNIT (H094)
211 A-1987-441-A SERVICE, DEVICE UNIT (2000) (SERVICE)
(including CP6001 (CMOS imager) and IS-095 complete
212 X-2589-179-1 CABINET FRONT ASSY (775) (BK) (BLACK)
ILCE-6000/6000L/6000Y_L2
3 213
217
#309
216
B
210
6 209
A
#5
#197
Imager Unit Section
(See page 2-9)
B
205
#309
#267
(Note 1)
5 204
A
202
203
201
1 #309
Ref. No. Part No. Description
212 X-2589-296-1 CABINET FRONT ASSY (775) (SI) (SILVER)
212 X-2590-979-1 CABINET FRONT ASSY (775) (WH) (WHITE)
213 4-530-664-01 VF RADIATION PLATE (775)
214 4-535-625-01 EM EYELET TAPE (775)
215 X-2589-183-1 STRAP BRACKET (L) ASSY (775)
216 4-487-875-01 HOLDER, EYELET TRIANGLE (779)
217 4-480-795-02 BUTTON, LENS LOCK (779) (BLACK)
217 4-480-795-11 BUTTON, LENS LOCK (779) (SILVER)
217 4-480-795-21 BUTTON, LENS LOCK (779) (WHITE)
#5 3-080-204-01 SCREW, TAPPING, P2
#197 4-185-990-01 MB SCREW, CHARGE UNIT FIXED
board) (Note 4) #267 4-287-436-21 SCREW (M1.7) (Note 1)
#309 4-300-115-21 TAPPING (1.7) (CH)
DISASSEMBLY
1. Remove in numerical order (
#309 X 2
1
Back View
2 215
ns
214
#309
#309
#309 X 1
4
Back View
Screw
#5: M1.7 X 3.5 (Tapping)
(Black)
3-080-204-01
1.7
3.5
Note
Note 1: Refer to "Assembly-4: Screw tightening sequence when
assembling the IM Heat Sink (2000)".
Note 2: The IM adjust washers (A, B, C) differ in thickness. Make
sure to return the removed IM adjust washers to original
places.
When replacing IM adjust washers, refer to "2-2. SELEC-
TION PARTS" on page 2-11.
If the original state cannot be restored due to loss of the IM
adjust washer, for example, replace the Device Unit (2000)
Service.
Note 3: Refer to "Assembly-5: IM Adjust Washer (A, B, C) putting
position".
Note 4: Precautions for Replacement of the Device Unit (2000)
Service
As CMOS Imager may be damaged by static electricity from its
structure, handle it carefully like for the MOS IC.
In addition, ensure that the receiver is not covered with dusts
nor exposed to strong light.
2-8
to ) in the left figure.
1 6
#309 X 1
2
Back View
#309
#309
#267 X 3
5
Back View
#309
#267
#197: M1.6 X 4.5 (Tapping) #267: M1.7 X 5.0 #309: M1.7 X 5.0 (Tapping)
(Silver) (Red) (Black)
4-185-990-01 4-287-436-21 4-300-115-21
1.6
1.7
4.5
5.0
Note 1: "Assembly-4: Screw tightening sequence when assembling
the IM Heat Sink (2000)"を参照してください。
Note 2: IM調整ワッシャ (A, B, C) は，それぞれ厚さが異なります。
取り外したIM調整ワッシャは，必ず元の位置に戻してくだ
さい。
また，IM調整ワッシャを交換する際は，2-11ページの"2-2.
SELECTION PARTS" を参照してください。
IM調整ワッシャを紛失するなどして元の状態に戻せなく
なった場合は，Device Unit (2000) Service を交換してくだ
さい。
Note 3: "Assembly-5: IM Adjust Washer (A, B, C) putting position" を
参照してください。
Note 4: Device Unit (2000) Service交換時の注意
CMOSイメージャは構造上，静電気により破壊される恐れが
あるため，MOS ICと同様に注意して取り扱ってください。
また，受光部にはゴミの付着，および強い光が入ることのな
いように注意してください。
#309 X 1
3
Back View
#309
#5 X 2
6
Back View
#5
1.7
5.0