Advertisement
Quick Links
Thank you for your purchase!
6 Cubby 65" TV Stand for up to 80" TV's
Assembly Time
60 min
Load Bearing
LBS
LBS
LBS
200 LBS
LBS
LBS
LBS
LBS
LBS
LBS
30 LBS
LBS
ASSEMBLY INSTRUCTIONS
Before You Begin:
Please identify all component parts and hardware pieces required before you begin. Carefully remove all of the
components from the packaging and set aside for assembly. Assemble on a soft surface to prevent scratching during
assembly.
Tighten all components securely before use. Failure to do so may result in personal injury.
DO NOT use any sharp objects to open plastic wrapped components as damage to product or components may result.
CHOKING HAZARD - Small Parts. Adult Assembly Required.
DO NOT ALLOW CHILDREN TO CLIMB ON FURNITURE
Serious or fatal injuries can occur from furniture tipping over. You must install Tipping Restraint Hardware (where
included) to help prevent the unit from tipping and causing accidental injury, instability, death or damage. The tipping
restraint is intended only as a safety measure, it is not a substitute for proper adult supervision.
To help prevent furniture from tipping over it must be permanently attached to the wall. Anti-Tip Safety Wall Straps
suitable for the unit weight and wall materials (if not included) should be purchased and installed.
Online Assembly Instructions:
http://ftp.flashfurniture.com/AssemblyInstructions/GC-MBLK66-GY-GG.pdf
Customer Service Email: CustomerExperience@belnick.com | Phone:866-552-2810
GC-MBLK66-ESP-GG/GC-MBLK66-GY-GG
Advertisement
Related Manuals for Belnick GC-MBLK66-ESP-GG
Summary of Contents for Belnick GC-MBLK66-ESP-GG
- Page 1 To help prevent furniture from tipping over it must be permanently attached to the wall. Anti-Tip Safety Wall Straps suitable for the unit weight and wall materials (if not included) should be purchased and installed. Online Assembly Instructions: http://ftp.flashfurniture.com/AssemblyInstructions/GC-MBLK66-GY-GG.pdf Customer Service Email: CustomerExperience@belnick.com | Phone:866-552-2810 GC-MBLK66-ESP-GG/GC-MBLK66-GY-GG...
- Page 2 This warranty will not cover: (1) labor, freight, or damage from misuse, abuse, negligence, alteration, assembly, installation, attachments, accident, vandalism, acts of nature or any other event beyond the control of Belnick; (2) tearing, scratching, scuffing, or blemishing of leather or fabric; (3) cosmetic damage that may result from normal usage; (4) damage attributable to use by persons exceeding specified weight limits or commercial use exceeding forty hours per week;...
- Page 3 PARTS 3.5*14 Left Front Fascia Top Plate （1） （11） Right Front Fascia Screws Bottom Plate （2） （12） Left Rear Fascia Left Side Panel Shelf Holders （3） （13） Bottom Support Feet Right Rear Fascia Right Side Panel （4） （14） Middle Shelf Inner Supports （5）...
- Page 4 STEP 1 Screw-In Pegs B*32 Dowel Pegs A*18 Right Inner Support Fascia （6） Left Inner Support Fascia （7） （1） Top Plate （5） *2 Front Upper Brace Inner Supports （8） （2） Bottom Plate （12） Right Front Fascia （4） Right Side Panel （14）...
- Page 5 STEP 3 Cam Lock Screw-In Peg （13） Receiver Hole Left Rear Fascia Left Side Panel （3） Ensure groove opening faces upwards （11） Left Front Fascia Receiver Hole STEP 4 3.5 Screws Bottom Support Feet STEP 3A: Attach Bottom Support Feet (Part H) to the underside of Bottom Plate (Part 2) using (8) 3.5 Screws (Part E) Bottom Plate...
- Page 6 STEP 5 STEP 5: Insert Cam Locks (Part C) into the Upper Front Panel (Part 8) and ensure the arrow side is facing outwards. Slide the Screw-In Pegs on the Left and Right Side Panels into the Cam Lock Receiver Holes in the Bottom Plate and Upper Front Panel (Part 8).
- Page 7 STEP 7 STEP 7: Ensure Cam Locks (Part C) are inserted in holes with open side facing outwards toward receiver hole for Screw- In pegs (Arrow Side). Slide Inner Supports (Part 5) onto Long Screw-In Pegs on the bottom plate. Turn the Cam Locks (Part D) clockwise to tighten.
- Page 8 STEP 9 （6） （7） Right Fascia STEP 9: Insert Cam Locks (Part C) into holes with arrow side pointing outwards. Insert preassembled Screw-In Pegs on Left Fascia (Part 7)and Right Fascia (Part 6) into the Receiver Holes and turn Cam Locks clockwise to Left Fascia tighten.
- Page 9 STEP 11 G*12 Shelf Holders （16） Right Shelf （15） Middle Shelf （16） Left Shelf STEP 11: Insert Shelf Holders (Part G) into holes at the desired height then place the Left & Right Shelves (Part 16) and the Middle Shelf (Part 15) onto Shelf Holders STEP 12 STEP 12:...
Need help?
Do you have a question about the GC-MBLK66-ESP-GG and is the answer not in the manual?
Questions and answers