Hyundai HDR 20 WIVA User Manual page 34

Mode button
Press to select the desired operation mode from
Dehumidifying,Dryer, Continuous dehumidifying
and Smart dehumidifying.
Note: Dryer and Smart dehumidifying modes are
optional.
(For control panel H)Press the MODE pad for 3
(For control panel K)Press the ION pad for 3
seconds to initiate the Wireless connection mode.
The LED DISPLAY shows'AP'(at this time the unit
shuts off all other functions) to indicate you can set
Wireless connection. If connection (router) is successful
within 8 minutes, the unit will exit Wireless connection
mode automatically and the unit reverts previous state.
If connection is failure within 8 minutes, the unit exits
the Wireless connection mode automatically.
Fan button (On some models)
(For control panel C&D&J&E&K&L&F)Control the fan
speed.Press to select fan speed in three steps-low,
med and high. The fan speed indicator light
illuminates under different fan speed settings. But
when select high fan speed, both the low and med
fan speed lights illuminate.
Turbo button (On some models)
(For control panel A&B&I&M&G)Control the fan speed.
Press to select either High or Normal fan speed. Set the
fan control to High for maximum moisture removal. When
the humidity has been reduced and quiet operation is
preferred, set the fan control to Normal.
(For control panel I)Control the fan speed. Press to
select fan speed in three steps-low, med and high. The
fan speed indicator light illuminates under different fan
speed settings. But when select high fan speed, both
the low and med fan speed lights illuminate.
Note: The turbo button is disabled in Dryer mode, the
Self clean, Air purifier or Anti-mould functions. Pressing
the turbo button for more than 3 seconds enables the
Self clean function and the LED DISPLAY shows 'SC' for
5 seconds. Press this button for 3 seconds again to
cancle the Self clean function, the LED DISPLAY flashes
'SC' for 5 seconds.
Timer button
Press to initiate the Auto start and Auto stop feature,
in conjuction with the
Page 13
 
and buttons.
Ion button(On some models)
Press to activate the ionizer. Anions are automatically
generated by ionization. The anions deactive the
airborne chemical vapors and dust particles. Press it
again to stop the function.
Fresh button(On some models)
Press to activate the ionizer. The ion generator is
energized and will help to purify the air inside. Press
it again to stop the function.
Wireless button(On some models)
Press this button for 3 seconds to initiate the Wireless
connection mode. The LED DISPLAY shows'AP' (at this
time the unit shuts off all other functions) to indicate
you can set Wireless connection. If connection (router)
is successful within 8 minutes, the unit will exit Wireless
connection mode automatically and the Wireless
indicator illuminates and the unit enters the previous
function. If connection is failure within 8 minutes, the
unit exits the Wireless connection mode automatically.
Pure/Anti-mould button(On some models)
Press this button to select the Air purifier function
which uses the included HEPA(High Efficiency
Particulate Air) filter to reduce the dust, bacteria and
allergen content in the room.
Press the button for 3 seconds to enable the Anti-mould
function. Press this button for 3 seconds again to cancle
the Anti-mould function and the unit revents previous
state.
UP( )/DOWN( ) buttons(On some models)
· Humidity Set Control buttons
The humidity level can be set within a range of 35%
RH(Relative Humidity) to 85%RH(Relative Humidity)
in 5% increments.
For drier air , press the
percent value(%).
For damper air, press the
percent value(%).
· TIMER Set Control buttons
Use the Up/Down buttons to set the Auto start and
Auto stop time from 0.0 to 24.
(For control panel E ) Note: Press
seconds to show the room temperature and quit to
show room temperature after 10 seconds.
button and set to a lower
button and set a higher
button for 3