Advertisement
Available languages
Available languages
TO KNOW IT'S UNIT
1. Adjustable Cutting Comb
2. Cutting Blades
3. Main Body
4. On/Off Switch
5. Charging Indicator
6. Charging Base
7. Thinning function On/Off Switch
1
2
7
3
4
5
6
CHARGING THE BATTERY
•
Connect the plug in the unit.
•
Ensure that the appliance is switch off.
•
Connect the Adapter plug to the power
supply.
•
The pilot light will be red when charging
•
It will take approximately 8 hours to finish
the charging. The first time 12H.
OPERATION
•
Before using, oil first, put 2 or 3 drops of
oil on the cutting blades.
•
Use the ON/OFF switch, to switch on or
switch off the appliance.
•
The appliance can be used for +/- 60
minutes if the battery is fully charged.
•
The appliance can be used directly with
adapter if needed or if no power of battery.
USING THE COMB ATTACHMENT
•
When load and unload the comb
attachment, please ensure the power
switch to "0" position.
•
Put the comb (long and sharp ends) into
slots of clipper at the sides.
•
Push the end of the comb to adjust the
length (push up for long cut & down for
shorter cut).
Note: There are 9 positions to control the
cutting length. (4/5.5/7/8.5/10/11.5/13/14.5/
16)
TRIMMING WITH THE THINNING GUIDE
The Thinning Guide is a device that allows
you to thin a chosen part of the hair rather
than trim it all at the same length. By
changing the position (7) you cut hair with
the Thinning Guide. Some of the hair gets
between the teeth of the clipper and is cut,
but most of the hair falls in the gaps between
the teeth and is not cut.
CLEANING AND MAINTENANCE
Before cleaning, always: switch off the
appliance, disconnect the apparatus and let
it cool.
Clean the outside of the apparatus with a
sponge or slightly wet linen.
The parts (removable) in contact with food
like plate, bowl, forks, Spatula etc. can be
washed in hot water with sponge and soft
detergent or put in the dishwasher.
Never plunge the apparatus in water or all
other liquid
Do not use abrasive cleaners, gritting, or
metal brush or another cutting object.
•
Take off the comb, remove the blade-set
clean the hair between the top-blade and
lower blade with brush.
•
The blade-set should be oiled frequently
in order to maintain its good cutting
performance and thus ensure a long
service life
•
To replace the blade-set position it with
the hook in the slot on the housing and
press until it clicks into place.
STORAGE
-
Ensure the unit is completely cool and dry.
-
Do not wrap the cord around the
appliance, as this will cause damage.
-
Keep the appliance in a cool, dry place
and out of reach from children.
4
DISPOSAL
Protect the environment
These hair clippers contain two permanently
in-built Ni-MH rechargeable batteries.
Do not dispose of the batteries or the device
with normal household refuse, contact your
local council to find out about environmentally
friendly and proper disposal of the device(as
electrical scrap) observe the applicable local
and national disposal regulations with regard
to separation of materials, waste collection
and recycling centre.
The packaging is wholly composed of
environmentally friendly materials that can be
disposed of at a local recycling centre
The following parts should be disposed of
separately
1. Motor, metal parts, circuit board
2. Mains adapter
3. Plastic parts
4. Rechargeable batteries
Recycling
This product bears the selective
sorting symbol for waste electrical and
electronic equipment (WEEE).
This means that this product must be
handled pursuant to European Directive
2002/96/EC in order to be recycled or
dismantled to minimize its impact on the
environment.
For further information, please contact your
local or regional authorities.
Electronic products not included in the
selective sorting process are potentially
dangerous for the environment and human
heath due to the presence of hazardous
substances.
Service centre
If the product doesn't function properly,
please contact your dealer or an authorised
service centre.
SPECIFICATION:
Power: 220-240V • 50/60Hz • 3W
Unit operating life is 3 years
STORAGE
It is recommended to store in a covered
and dry place at an ambient temperature
not higher than + 40° C with relative
humidity above 70% and the absence in the
environment of dust, acid and other vapours.
TRANSPORTATION
To the device special transportation rules are
not applied. When transporting the unit, use
the original packaging. During transportation,
avoid drops, impacts and other mechanical
influences on the device, as well as direct
exposure to atmospheric precipitation and
aggressive environments.
5
Advertisement
