Table of Contents
Advertisement
Information in this document is subject to change
without notice.
Sony, VAIO and CLIE are trademarks or
registered trademarks of Sony. Microsoft,
Windows, Windows Media, Outlook, Bookshelf
and other Microsoft products are trademarks or
registered trademarks of Microsoft Corporation
in the United State and other countries.
The word Bluetooth and the Bluetooth logo are
trademarks of Bluetooth SIG, Inc. AMD, the
AMD logo, other AMD product names and
combinations thereof are trademarks of
Advanced Micro Devices, Inc. Intel Inside logo,
Pentium and Celeron are trademarks or registered
trademarks of Intel Corparation. Transmeta, the
Transmeta logo, Crusoe Processor, the Crusoe
logo and combinations thereof are trademarks of
Transmeta Corporation in the USA and other
countries. Graffiti, Hotsync, PalmModem, and
Palm OS are registered trademarks, and the
Hotsync logo and Palm are trademarks of Palm,
Inc. or its subsidiaries. (M) and Motrola are
trademarks of Motrola, Inc. Other Motrola
pruducts and services with (R) mark like
Dragomball are the trademarks of Motrola, Inc.
All other name of systems, products and services
in this manual are trademarks or registered
trademarks of their respective owners.
In this manual, the (TM) or (R) mark are not
specified.
Caution Markings for Lithium/Ion Battery - The
following or similar texts shall be provided on
battery pack of equipment or in both the
operating and the service instructions.
CAUTION: Danger of explosion if battery is
incorrectly replaced. Replace only with the same
or equivalent type recommended by the
manufacturer. Discard used batteries according
to the manufacturer's instructions.
CAUTION: The battery pack used in this device
may present a fire or chemical burn hazard if
mistreated. Do not disassemble, heat above
100°C (212°F) or incinerate.
Dispose of used battery promptly.
Keep away from children.
CAUTION: Changing the back up battery.
• Overcharging, short circuiting, reverse
charging, multilation or incineration of the cells
must be avoided to prevent one or more of the
following occurrence; release of toxic materials,
release of hydrogen and/or oxygen gas, rise in
surface temperature.
• If a cell has leaked or vented, it should be
replaced immediately while avoiding to touch
it without any protection.
Service and Inspection Precautions
1.
Obey precautionary markings and
instructions
Labels and stamps on the cabinet, chassis, and
components identify areas requiring special
precautions. Be sure to observe these precautions, as
well as all precautions listed in the operating manual
and other associated documents.
2.
Use designated parts only
The set's components possess important safety
characteristics, such as noncombustibility and the
ability to tolerate large voltages. Be sure that
replacement parts possess the same safety
characteristics as the originals. Also remember that
the ! mark, which appears in circuit diagrams and
parts lists, denotes components that have particularly
important safety functions; be extra sure to use only
the designated components.
3.
Always follow the original design
when mounting parts and routing
wires
The original layout includes various safety features,
such as inclusion of insulating materials (tubes and
tape) and the mounting of parts above the printer
board. In addition, internal wiring has been routed and
clamped so as to keep it away from hot or high-voltage
parts. When mounting parts or routing wires, therefore,
be sure to duplicate the original layout.
PCG-Z1WA/Z1WAMP1/Z1WAMP2/Z1WAMP3/Z1WAP/Z1XFP (AM)
– 2 –
PCG-Z1VXCNP/Z1VXCP/Z1VXZLP/Z1XGP/Z1XJP/Z1XLP/Z1XTP/Z1XZC/Z1XZCN
4.
Inspect after completing service
After servicing, inspect to make sure that all screws,
components, and wiring have been returned to their
original condition. Also check the area around the repair
location to ensure that repair work has caused no damage,
and confirm safety.
5.
When replacing chip components...
Never reuse components. Also remember that the
negative side of tantalum capacitors is easily damaged
by heat.
6.
When handling flexible print
boards...
• The temperature of the soldering-iron tip should be
°
about 270
C.
• Do not apply the tip more than three times to the same
pattern.
• Handle patterns with care; never apply force.
Caution: Remember that hard disk drives are easily
damaged by vibration. Always handle with care.
ATTETION AU COMPOSANT AYANT
RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFÉS PAR UNE
M A R Q U E ! ! ! ! !
S U R L E S D I A G R A M M E S
SCHÉMATIQUES ET LA LISTE DES PIÈCES
SONT CRITIQUES POUR LA SÉCURITÉ DE
FONCTIONNEMENT. NE REMPLACER CES
COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉSDANS
CE MANUEL OU DANS LES SUPPÉMENTS
PUBLIÉS PAR SONY.
Confidential
PCG-Z1X/Z1XE (J)
PCG-Z1XEP/Z1XMP/Z1XSP (EU)
(AO)
Advertisement
Table of Contents
