Related Manuals for scope Connexions CX5E
Summary of Contents for scope Connexions CX5E
- Page 1 www.acornfiresecurity.com Connexions CX5 Radio Paging Transcoder Mains, Multi Port Version Installation & User Manual CX5red Issue 2 www.acornfiresecurity.com...
- Page 2 For UK equipment, Scope has no control of the use and application of the frequencies issued by OFCOM. Some equipment that is licensed may have greater protection than other equipment which is operated on a WT Act License Exempt basis.
- Page 3 Liability Scope does not accept liability for any damage or injury, howsoever caused as the result of misuse of this equipment. It is the responsibility of the user to ensure that the equipment is operated in the manner for which it was intended and that it is the correct item of equipment for the required task.
-
Page 4: System Overview
ConneXions CX5 Mains, Multi Port Version System Overview The Scope Connexions 5 is a POCSAG data display radio paging system which can be used to transmit both text and numeric messages direct to pocket pagers carried by individuals or entire groups. - Page 5 Coaxial cable intended for TV, Satellite or CCTV installations is normally 75 OHM and therefore totally unsuitable for any transmitter installation manufactured by Scope. Also remember that the performance of the system will be effected by the type of material the unit is mounted on and its surroundings.
- Page 6 (CTS) IN +5V 100mA max (for Scope peripherals) As information passes only from the host equipment to the ConneXions transcoder, you will only need to read the DTR line which if high shows that power is applied to the Connexions unit. The RTS line will be high when the transcoder is ready to receive data.
- Page 7 www.acornfiresecurity.com ConneXions CX5 Mains, Multi Port Version DIAGRAM 1 CX5red Issue 2 Page 6 of 13 www.acornfiresecurity.com...
-
Page 8: Section 2: System Operation
www.acornfiresecurity.com ConneXions CX5 Mains, Multi Port Version Section 2: System Operation Confirmation of power connection is by way of the red LED on the base of the transcoder console. Confirmation of transmit is provided by way of the momentary green LED on the base of the transcoder console. - Page 9 www.acornfiresecurity.com ConneXions CX5 Mains, Multi Port Version Optional Dry Contacts This option must be specified at time of ordering, along with the pre-programmed messages required. The purchaser should also order the dry contact interface box (Part Code: DC8) for ease of connection to the contact terminals (see Diagram 2).
- Page 10 www.acornfiresecurity.com ConneXions CX5 Mains, Multi Port Version As a default, contacts are programmed as Normally Open (N/O), with a repeat transmission every two minutes if still active. For customers who wish to connect directly to PL1, the pinout arrangement on the 9 way D plug is shown below: PL1, 9 way D Plug Dry Contact No.
-
Page 11: Other Antennas
In the event that a pager requires service, return it directly to Scope (in the pre-addressed service bag supplied with your system) by registered post. Ensure that you carefully fill out the service form provided. -
Page 12: System Specification
330 (L) x 190 (W) x 70 (D) max *dependent on system configuration excluding aerial ** subject to applicable country’s licencing conditions Scope’s policy is one of continuous development and specifications are subject to change without notice CX5red Issue 2 Page 11 of 13... -
Page 13: Section 3: Technical Information
www.acornfiresecurity.com ConneXions CX5 Mains, Multi Port Version Section 3: Technical Information This section provides a more in depth understanding of how messages are formatted for serial communication from a host. It need only be studied by those intending to write their own serial comm.’s software. - Page 14 www.acornfiresecurity.com ConneXions CX5 Mains, Multi Port Version Section 3: Technical Information Next follows the 7 digit pager identity number. All seven digits must be used. The letter following the identity is the beep type of which there are four valid characters, A, B, C or D. Next follows the message to be transmitted, which can include: 0-9, space, -(hyphen), ‘U’...