Electric Motor Mounting Plate Asasembly ..46-47 Terms and Conditions of Sale ....... 112 Specification and part number NOTE are subject to change without notice PAGE 4 —STOW CMS-64S CONCRETE MIXER — OPERATION & PARTS MANUAL — REV. #3 (08/04/06)
Safety Message Alert Symbols. NOTE be damaged if you do not follow instructions. PAGE 8 —STOW CMS-64S CONCRETE MIXER — OPERATION & PARTS MANUAL — REV. #3 (08/04/06)
■ NEVER! place hands inside the drum while the drum is equipment and/or injury to user may result. rotating. ■ Manufacturer does not assume responsibility for any accident due to equipment modifications. STOW CMS-64S CONCRETE MIXER — OPERATION & PARTS MANUAL — REV. #3 (08/04/06) — PAGE 9...
Page 9
■ High Temperatures – Always stop engine and allow the engine to cool before adding fuel, oil or performing service and maintenance functions. Contact with hot components can cause serious burns. PAGE 10 —STOW CMS-64S CONCRETE MIXER — OPERATION & PARTS MANUAL — REV. #3 (08/04/06)
Machine Safety Decals The STOW CMS-64S mixer is equipped with a number of safety decals (Figure 1A). These decals are provided for operator safety and maintenance information. The illustration below and on the next page shows these decals as they appear on the machine.
Page 11
Table 5. Remember cable distance affects the engine. current-voltage capacity of the extension cable. ) . s , s t . c t PAGE 12 —STOW CMS-64S CONCRETE MIXER — OPERATION & PARTS MANUAL — REV. #3 (08/04/06)
24 inches into reference the frame assembly drawing and parts list in this the lift pockets. manual to determine which tow bar meets your requirements. STOW CMS-64S CONCRETE MIXER — OPERATION & PARTS MANUAL — REV. #3 (08/04/06) — PAGE 13...
The STOW CMS-64S concrete mixer is shipped with the handwheel detached. Attach the handwheel to the mixer as shown in Figure 4. Figure 4. Handwheel Assembly STOW CMS-64S CONCRETE MIXER — OPERATION & PARTS MANUAL — REV. #3 (08/04/06) — PAGE 15...
3. As a minimum, use a 1/2-inch bolt and nylock nut grade position (gasoline models only). 5 when securing either tow bar to the towing vehicle, PAGE 16 —STOW CMS-64S CONCRETE MIXER — OPERATION & PARTS MANUAL — REV. #3 (08/04/06)
1/2-inch bolt through tow bar and frame. vehicle. Secure tow bar to frame with 1/2-inch nylock nut. Tighten to 40 ft.-lbs. Figure 5. Tow Bar and Safety Chain Installation STOW CMS-64S CONCRETE MIXER — OPERATION & PARTS MANUAL — REV. #3 (08/04/06) — PAGE 17...
. t f . t f . t f . t f a t l PAGE 18 —STOW CMS-64S CONCRETE MIXER — OPERATION & PARTS MANUAL — REV. #3 (08/04/06)
Page 18
STOW CMS-64S CONCRETE MIXER — ELECTRIC MOTOR Figure 7. Single Phase Electric Motor with 12 inch Pigtail Cable STOW CMS-64S CONCRETE MIXER — OPERATION & PARTS MANUAL — REV. #3 (08/04/06) — PAGE 19...
Page 19
Check the zerk grease fittings (Figure 27) as shown in the maintenance section of this manual. These grease fittings lubricate the handwheel and the yoke mechanism . Figure 9. Engine Oil Dipstick (Oil Level) PAGE 20 —STOW CMS-64S CONCRETE MIXER — OPERATION & PARTS MANUAL — REV. #3 (08/04/06)
Page 20
Move the throttle lever (Figure 12) away from the slow position, about 1/3 of the way toward the fast position. Figure 15. Starter Grip Figure 12. Throttle Lever STOW CMS-64S CONCRETE MIXER — OPERATION & PARTS MANUAL — REV. #3 (08/04/06) — PAGE 21...
NOTE extension cord so that it lays flat and is not curled underneath the mixer. Figure 18. Electric Motor ON/OFF Switch (ON Position) PAGE 22 —STOW CMS-64S CONCRETE MIXER — OPERATION & PARTS MANUAL — REV. #3 (08/04/06)
(OFF Position) Disconnect the electric motor's extension cord from its power source. Figure 20. Filling Mixing Drum Clean drum of all debris and foreign matter. STOW CMS-64S CONCRETE MIXER — OPERATION & PARTS MANUAL — REV. #3 (08/04/06) — PAGE 23...
Page 23
) 3 ( a i c i t a r e t t n i r e t . s l PAGE 24 —STOW CMS-64S CONCRETE MIXER — OPERATION & PARTS MANUAL — REV. #3 (08/04/06)
For thorough mix and longer drum life, always wash drum out after each use. NEVER! pour or spray water over the engine or electric Figure 28. Grease Fittings Electric Motor motor. PAGE 26 —STOW CMS-64S CONCRETE MIXER — OPERATION & PARTS MANUAL — REV. #3 (08/04/06)
Page 26
ALWAYS wear safety glasses NOTE when removing or installing force fitted parts. Failure to comply may result in serious injury. Figure 30. Suspension Components STOW CMS-64S CONCRETE MIXER — OPERATION & PARTS MANUAL — REV. #3 (08/04/06) — PAGE 27...
Page 27
Place the mixing drum in the down position (mouth facing downward). Cover the mixer and place it a clean dry area, that is protected from harsh elements. Figure 31. Wheel Lug Nuts Tightening Sequence PAGE 28 —STOW CMS-64S CONCRETE MIXER — OPERATION & PARTS MANUAL — REV. #3 (08/04/06)
>, belong to the same assembly or kit. If more than one of the same NOTE reference number is listed, the last one listed indicates newest (or latest) part available. PAGE 32 —STOW CMS-64S CONCRETE MIXER — OPERATION & PARTS MANUAL — REV. #3 (08/04/06)