Advertisement
Quick Links
Advertisement
Related Manuals for latch C2
Summary of Contents for latch C2
- Page 1 Installation Guide...
- Page 2 Table of contents Things you should know Included in the box Hardware Preparation Installation Document number 770-00018 V1 Regulatory compliance Revised on 10/27/2020...
- Page 3 The product certifications depend on install in accordance with this guide. More resources, including the electronic version of this guide, can be found online at support.latch.com. C2 Installation Guide Version 1.0...
- Page 4 Inside the box C2 Installation Guide Version 1.0...
- Page 5 Hardware 1-3/4” 1-3/8” Depending on door thickness C2 Installation Guide Version 1.0...
- Page 6 Preparation Here’s how to prepare your door and device for the correct door thickness and device backset. C2 Installation Guide Version 1.0...
- Page 7 Preparation Measure 1- 3 /4" 1- 3 / 8 " Select the correct cutsheet according to the door thickness. Identify if your door has backset A, 2-3/4”, or backset B, 2-3/8”, with the cutsheet. C2 Installation Guide Version 1.0...
- Page 8 Preparation Deadbolt Deadbolt body Before Deadbolt hub Deadbolt After Important: Before you begin installation, make sure the deadbolt is extended. C2 Installation Guide Version 1.0...
- Page 9 Preparation Deadbolt A. Extend B. Retract The deadbolt extends or retracts by rotating the body of the Extend or retract the body of the deadbolt depending on the deadbolt 180º. backset type. C2 Installation Guide Version 1.0...
- Page 10 Choose the respective mounting screws according to your door If you have a 1-3/8” thick door, break the tailpiece to shorten it by thickness. grabbing with pliers on both sides of the notch and snapping off the end. C2 Installation Guide Version 1.0...
- Page 11 After choosing Left-handed door left-handed Before Two screws are directly above the tailpiece. Remove the screw for the handing you are not installing. The screw indicating door After choosing Right-handed door handing will remain. right-handed C2 Installation Guide Version 1.0...
- Page 12 Installation Once your door is prepped, proceed with installation. C2 Installation Guide Version 1.0...
- Page 13 If the door only has the 1” cross bore and no mortise for a Important: Make sure that the deadbolt hub is on the bottom. faceplate, remove the faceplate and armor plate from the deadbolt. Press the drive-in option onto the end of the deadbolt. C2 Installation Guide Version 1.0...
- Page 14 Turn the deadbolt hub so that the deadbolt is extended. Screw the deadbolt in if using the provided rounded-corner Insert in the door, and keep the deadbolt extended throughout faceplate. the installation. C2 Installation Guide Version 1.0...
- Page 15 Before After choosing After choosing left-handed right-handed Prepare the outer trim. The tailpiece will be vertical for both left Refer back to final preparation step to ensure the correct handing and right-handed doors. configuration. C2 Installation Guide Version 1.0...
- Page 16 The cable routes over the deadbolt. The post goes over the deadbolt. Insert the outer trim into the deadbolt. It is recommended to support the tailpiece with the index finger of your off hand. C2 Installation Guide Version 1.0...
- Page 17 Separate the back cover. C2 Installation Guide Version 1.0...
- Page 18 Alignment post hole Thumb turn hub Rotate the thumb-turn hub so that it is in the vertical position. Then place the battery tray assembly while ensuring that the cable and post go in their respective holes. C2 Installation Guide Version 1.0...
- Page 19 1- 3 /4" 1- 3 / 8 " Select the set of screws for your door thickness. Screw the two shorter screws from the set in the battery tray assembly. C2 Installation Guide Version 1.0...
- Page 20 Take the remaining longer screw for your door thickness, and trim. Recycle the post if ABS is collected in your area. Do not install it in the hole where you removed the red post. pull the post out. C2 Installation Guide Version 1.0...
- Page 21 Make sure the inner assembly is straight and the tailpiece turns Connect the cable as shown, with the white arrow facing you. freely. If not, adjust as needed. Route the slack as shown. C2 Installation Guide Version 1.0...
- Page 22 Snap the cable cover on as shown. Install 6 AA non-rechargeable alkaline batteries in the polarity shown. Note the two tabs the bottom batteries slide behind. C2 Installation Guide Version 1.0...
- Page 23 Download Latch Manager App and configure. Orient the thumb turn in the same direction as the deadbolt, place inner trim, and secure with the trim screw. Check for smooth operation of the deadbolt, and adjust as needed. C2 Installation Guide...
- Page 24 Install the strike plate and reinforcement plate as specified for your installation. C2 Installation Guide Version 1.0...
- Page 25 20 cm from all persons and must not be co-located or operating in conjunction with any other Equipment List) d’Industrie Canada rendezvous sur: http://www.ic.gc.ca/app/sitt/reltel/srch/ antenna or transmitter. nwRdSrch.do?lang=eng Pour des informations supplémentaires concernant l’exposition aux RF au Canada rendez-vous sur: http://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf08792.html C2 Installation Guide Version 1.0...