Table of Contents
Advertisement
Quick Links
DIGISYNTHETIC
EXCELLENT POWER AMPLIFIER
DIGISYNTHETIC
Channel A
DP48 00
-18
-21
-14
-24
-8
PROTECT
-28
-4
-36
- 2
-
0
R
DP 3200
PROTECT
CLIP
SIGNAL
-18
- 21
-14
- 24
-8
SIG/CLIP
-28
BRIDGE
- 36
- 2
0
-
DP Series
Power Amplifier
DP4800
DP3200
DP2240
DP1800
DP1400
DP2200
DP1200
Chann el B
-18
-21
-14
-24
-8
-28
-36
- 2
-
0
USER MANUAL
POWER
- 18
- 21
- 14
PROTECT
- 24
- 8
SIG/CLIP
- 28
BR IDG E
- 36
-2
0
-
R
Advertisement
Table of Contents
Related Manuals for DIGISYNTHETIC DP2200
Summary of Contents for DIGISYNTHETIC DP2200
- Page 1 DIGISYNTHETIC DP4800 DP3200 DP2240 DP1800 EXCELLENT POWER AMPLIFIER DP1400 DP2200 DP1200 DIGISYNTHETIC DP 3200 PROTECT CLIP SIGNAL POWER Channel A Chann el B DP48 00 - 18 - 21 - 21 - 14 PROTECT PROTECT - 24 - 24 SIG/CLIP...
-
Page 2: Important Safety Instruction
IMPORTANT SAFETY INSTRUCTION WARNING When using electric products, basic precautions should always be followed: 1. Read all the SAFETY INSTRUCTIONS before using the product. 2. This product must be earthed. If it has malfunction or breaks down, grounding provides a path of least resistance for electric current to reduce risk of electric shock. - Page 3 Installation & operating instruction Mains power connection. Before connecting the amplifier to the mains power socket, make certain that the voltage corresponds with that indicated on the rear of the unit (an allowance of 10% is acceptable). Before connecting the power cable to the mains, always make certain that it is not damaged and that there are no bare wires, always connect the power cable to the amplifier before switching it on and only remove the cable after switching it off.
- Page 4 FEATURE Perfect electronic protections: short circuit/overload protection, overheating protection and direct current excursion protection. Low noise and lower distortion Three output modes: stereo, mono and bridge(only for D 1400) THD+N: 0.08%@1kHz Frequence response: 20Hz-20kHz...
-
Page 5: Control Panel
CONTROL PANEL FRONT PANEL DIGISYNTHETIC DP 3200 PROTECT CLIP SIGNAL BRIDGE POWE R Channel A Ch an nel B 1. POWER: ON/OFF switch 2. CHA\B LEVEL : Adjust the volume of four channels Control of the input level of the external signal: operates with continual... -
Page 6: Limit Leds
2)VOLTAGE PROTECTION: trips in the event of a short-circuit or overload, limiting the output current. 3)CIRCUIT DAMAGE PROTECTION: in the events of damage, limit the damage to extend, minish the loss. Some protection situations require the amplifier to be switched off and then back on for normal operating conditions be restored. -
Page 7: Rear Panel
B. REAR PANEL... - Page 8 8. OUTPUTS Power out : outputs to be connected to the loudspeaker enclosures. Amplifier's A&B outputs both have BINDING-POST connectors and speaker connectors Only loudspeaker(or loudspeaker enclosure systems)within the amplifier's declared power and Impedance load range should be connected to the amplifier's outputs (see Technical pecifications).
-
Page 9: Connector Cable
CONNECTOR CABLE The following diagrams illustrate the wiring of the various types of sockets that can be used with the DSP power amplifiers. To connect the amplifier to the mixer, always make certain to use only signal cables (screened cables made up of two wires plus a braid screen ), not power cables (speaker cables, normally made up of two wires, usually with a greater cross-section): the use of unscreened cables could in fact cause annoying buzzes and background noise. -
Page 10: Specification
RMS 4 x 450W (8 ) 4x 700W (4 ) Ω BRIDGE 2 x 1300W (8 ) (only for D 4800) × Ω × Ω DP2200 RMS 2 450W (8 ) 2 750W (4 ) × Ω BRIDGE 1 1300W (8 ) ×...