ZLINK PA-100 Quick Start Manual

Connecting Things That Matter
PA-100
This product speaks
with other Z-Wave
Plug In Switch
cer�fied devices
INTRODUCTION
ZLINK PA-100 is a Z-Wave Plus® cer�fied device with S2 security and SmartStart
features. You can now add this device securely and with ease using QR code on the
product with compa�ble gateways suppor�ng S2 and Smart Start. PA-100 is a
member of the Z-Wave family and communicates with other Z-Wave cer�fied
devices in a control network. PA-100 can be used to turn On or Off lamps or AC
operated appliances. Each Z-Wave device also serves as a node to repeat the signal
in the network, thus, extending the overall Z-Wave mesh wireless network range.
Different types and brands of Z-Wave devices can be associated with the PA-100 in
your system and they will work together to op�mize and expand the coverage of
your Z-Wave network. For more informa�on on this and other quality ZLINK
Products please visit www.ZLINKProducts.com.
FEATURES
• Works with incandescent, florescent (CFL) or LED ligh�ng and AC operated appliance
• ON/OFF status and loca�on LED indicator
• Remotely or manually turns ON or OFF lights
• Does not block the second AC outlet
• Z-Wave 500 Series module inside
• Grounded 3-pin AC power receptacle and plug to enhance safety.
• Internal rese�able fuse to protect from surge current
• Works with any cer�fied gateway suppor�ng Z-Wave
• Z-Wave 500 Series module inside
• Please find the QR code label with DSK on the bo�om of the device
! WARNING !
RISK OF FIRE, ELECTRICAL SHOCK & BURNS
DO NOT USE WITH MEDICAL AND LIFE SUPPORT INSTRUMENT
No user serviceable parts are in this module
To reduce the risk of electric shock, this product has a grounding type plug that has
a third (grounding) pin. This plug will only fit into a grounding type power outlet.
If the plug does not fit into the outlet, contact a qualified electrician to install the
proper outlet. Do not change the plug in any way.
The appliance connected to this Z-Wave module must not exceed 900W
incandescent, 200W CFL/LED, ½ horsepower motor and 15A, 1800W resis�ve load.
SETUP
Step 1 Plug the 2-pin AC power plugs of ligh�ng
device to the receptacle of PA-100.
Step 2 Insert the module's 3-pin plug into an AC
outlet in the same room as your gateway.
In normal opera�ng mode, the LED on the
front panel will be lit.
Step 3 Add (Include) the module into your network by a Z-Wave cer�fied controller.
Please refer to your gateway's or the controller's instruc�ons manual for details.
Normally, the sequence is as follows:
1. Place your network controller into inclusion mode by following the controller
manufacturer's instruc�ons.
2. When the controller is ready, single click the bu�on on the front of PA-100.
The controller should indicate that the new device was added successfully
3. Once the has been successfully added to your home network, you can move
it to the preferred loca�on in the home.
If the controller shows it failed, repeat the procedure.
Manual Reset
If Inclusion s�ll fails a�er the 2nd a�empt, you need to first reset the PA-100
before repea�ng the above step. The manual reset method is as follows:
1. Unplug PA-100 from the AC outlet and
also unplug the power plug of the
appliance from PA-100 (if plugged in).
2. Press and hold the bu�on on the PA-100.
www.ZLINKProducts.com
3. Plug the PA-100 back into the AC outlet with the bu�on pressed
A�er 3 seconds, release the bu�on. If you see the bu�on blink, that means that
PA-100 has been reset successfully and you may retry Step 3 above to add the
module into your network. Otherwise, please repeat the manual reset procedure.
Note: If the PA-100 was previously Added (Included) in your network, rese�ng it
locally does not mean it has been removed from your network. If you wish to
remove PA-100 from your network you will need to Delete (Exclude) the module
from the network by your controller.
Use the manual reset procedure only in the event that the network primary
controller is lost or otherwise inoperable.
BASIC OPERATION
The connected ligh�ng devices can be controlled manually with a push bu�on
OR Wirelessly with a remotely
Press here
A Z-Wave cer�fied controller is capable of se�ng up ZLINK products in your
desired network. Once the device is added, you may assign it to a Group.
Furthermore, it can be set in Associa�on with another Z-Wave device to
perform a specific triggered func�on such as turning lights on when mo�on
is detected. Please refer to the instruc�ons manual of your controller for
details and procedures on how these se�ngs can be done.
In the event of a power failure, the ZLINK device will return to the last se�ng
a�er the power is restored.
About the push bu�on:
There is a single bu�on on PA-100 for manual opera�on that:
A) Manually turns the connected ligh�ng ON/OFF by pressing the bu�on. It
func�ons as a toggle switch; if the light is ON, pressing the bu�on turns
the light OFF and vice a versa.
B) Adds(Includes) or Deletes(Excludes) your PA-100 to/from your Z-Wave
network. Please refer to the instruc�ons manual of your gateway or
remote controller for detail procedures on how these ac�ons can be done.
This push bu�on is also backlit with an LED indicator that will be On when the
connected appliance is Off, and vice versa. The module may be easily spo�ed
even in a dark environment.
ADVANCED CONFIGURATION
Configurable Parameter Se�ngs: If your controller supports Z-Wave configurable
parameters, the following se�ngs can be modified.
Parameters
# Descrip�on
When value = 0, the LED indicator will be
3
Nightlight
OFF when the connected appliance is
ON, and the LED indicator will be ON
when the connected appliance is OFF.
If value = 1, the LED indicator will be OFF
when the connected appliance is OFF,
and the LED indicator will be ON when
the connected appliance is ON.
If value = 2, the LED indicator will be
always OFF regardless of the load status.
Depending on the capability of your controller or gateway so�ware, the following
simple to advanced opera�ons can be performed. Please refer to the controller's or
gateway manual for details.
Associa�on:
1. PA-100 supports group one for lifeline communica�on.
2. You can only associate one Z-Wave device to group one.
3. Lifeline associa�on only supports the "manual reset" event.
4. For instruc�ons on how to "set lifeline associate", please refer to your controller/
gateway instruc�ons.
www.ZLINKProducts.com
Values Default Bytes
0 1