Channel/Clock Settings When Tv Guide On Screen System Is Not Used; Auto Channel/Clock Settings; Adjust Time Zone - Panasonic DMR-EH75VS Operating Instructions Manual

Channel/Clock settings when TV Guide On Screen
Refer to the control reference on page 74.
Preparation:
If the program listings has already been downloaded, return the unit to the factory preset condition using the steps indicated below.
When the unit is on and stopped
1 Press and hold [CH, X] and [CH, W] on the main unit for about 5 seconds.
The unit turns off.
2 Press [Í, DVD/VHS POWER] to turn the unit on.
3 After the language and TV aspect is setup, press [RETURN] and exit the TV Guide
On Screen ® system setup screen.
Note
You can set scheduled recording only manually after you set the unit with "Set Channels
Automatically".

Auto channel/clock settings

[1]
While stopped
Press [FUNCTIONS].
[2] Press [3, 4] to select "Other Functions" and
then press [ENTER].
[3] Press [3, 4] to select "Setup" and then press
[ENTER].
Press [3, 4] to select "Channel" and then
[4]
press [1].
[5] Press [3, 4] to select "Set Channels
Automatically" and then press [ENTER].
[6]
Press [ENTER].
Auto Channel Setting starts. This takes a few minutes.
The unit then proceeds with Auto Clock Setting. The time is
displayed when finished.
Setup
Set Clock Automatically
Channel
Auto Clock Setting is complete.
Setup
Disc
11/4/2006 12:15 AM
Video
DST.............. On
Time Zone..... CST
Audio
Display
≥DST, Daylight Saving Time, shows the summertime setting.
≥TIME ZONE shows the time difference from Greenwich Mean
Time (GMT).
EST (Eastern Standard Time)
CST (Central Standard Time)
MST (Mountain Standard Time) l GMT j7
PST (Pacific Standard Time)
AST (Alaska Standard Time)
HST (Hawaii Standard Time)
For other areas: xx hr
≥If the Auto Clock Setting does not start automatically, select
"Clock Settings" from the "Setup" tab and then select "Set
Clock Automatically".
≥If the time was not set correctly, use manual clock setting
(l 25) or adjust time zone.
[7]
Press [ENTER].
≥Regarding DST (Daylight Saving Time) l 25
To return to the previous screen
Press [RETURN].
To exit the screen
Press [RETURN] several times.
To cancel partway while Auto Channel/Clock Setting is taking place
Press [RETURN].
To set so the TV Guide On Screen
When the power is turned on and the Start setup screen is displayed, press [3, 4] to select "Don't remind me again" and press [ENTER].
l GMT j5
l GMT j6
l GMT j8
l GMT j9
l GMT j10
® system is not displayed automatically when you turn the unit on
system is not used
®
≥The unit configures channels according to the Signal Source
(RF IN) settings as follows.
Signal Source
(RF IN)
VHF
Antenna
UHF
VHF
CATV LOW BAND
CATV MID/SUPER BAND
CableTV
CATV HYPER BAND
ULTRA BAND
SPECIAL CATV CHANNEL

∫ Adjust Time Zone

Adjust the time zone (j1 or i1) if it was not set correctly with auto
clock setting.
You cannot change this setting if you set the clock manually.
[1]
While stopped
Press [FUNCTIONS].
Press [3, 4] to select "Other Functions" and
[2]
then press [ENTER].
[3] Press [3, 4] to select "Setup" and then press
[ENTER].
Press [3, 4] to select "Setup" and then press
[4]
[1].
[5] Press [3, 4] to select "Clock Settings" and
then press [ENTER].
Press [3, 4] to select "Adjust Time Zone" and
[6]
then press [ENTER].
Setup
Adjust Time Zone
j1
Channel
Setup
i1
Disc
Video
Audio
≥Regarding DST (Daylight Saving Time) l 25
Press [3, 4] to select "s1" or "r1" and then
[7]
press [ENTER].
Band Channel
2 to 13
14 to 69
2 to 13
95 to 99
14 to 36
37 to 65
66 to 94
100 to 125
1
0
79
RQT8346