Table of Contents
Advertisement
Quick Links
Operator Instructions
Includes - Foreseen Use, Work Stations, Putting Into Service,
Operating, Dismantling, Assembly and Safety Rules
Manufacturer/Supplier
Universal Air Tool Company Limited
Unit 8
Lane End Industrial Park
High Wycombe
Bucks
HP14 3BY
Tel No
(01494) 883300
Product Nett Weight
3.52
lbs
1.6
Kg
Air Pressure
Recommended Working
Recommended Minimum
Maximum
Personal Safety Equipment
Use - Safety Glasses
Use - Safety Gloves
Use - Safety Boots
Use - Breathing Masks
Use - Ear Protectors
Foreseen Use of the Tool
The tool is designed for the purpose of chipping, riveting and
scaling of metals and stone. In general terms a reciprocating free
piston in the cylinder of the tool imparts a blow to the chisel or
working attachment. A list of suitable equipment to use with this
tool can be provided by the manufacturer. Do not use the tool for
any other purpose than that for which it was designed without
consulting the manufacturer or the manufacturer's authorised
representative.
Do not modify the tool for it's use as a chipper etc. or for any
other purpose without first agreeing any such modification with
the manufacturer or the manufacturer's authorised representative.
Work Stations
The tool should only be used as a handheld, hand operated tool.
It is always recommended that the tool is used when standing on
a solid floor. It can
be used in other
positions
but
before any such
use, the operator
must
be
in
a
secure
position
having a firm grip
and footing and be
aware
of
a
reaction force on
the hand as result
of the tool doing
work.
Fax No
(01494) 883237
Recommended Use Of
Balancer Or Support
No
6.3
bar
90
PSI
n/a
bar
n/a
PSI
7.0
bar
100
PSI
Yes
Yes
Yes
Page No 1
Important
Read these instructions carefully before installing, operating,
servicing or repairing this tool. Keep these instructions in a safe
accessible place.
Product Type
0.401 Shank Air Hammer
Model No/Nos
UT8612-B Round Shank
UT8613-B Hex Shank
Recommended Hose Bore
Size - Minimum
3/8
10
Ins
M/M
Noise Level Sound Pressure Level 102.7 dB(A)
Sound Power Level 115.0 dB(A)
Test Method Tested in accordance with Pneurop
test code PN8NTC1 and ISO Standard 3744
Vibration Level
Test Method Tested in accordance with ISO
standards 8662 Parts 1 & 2
Putting Into Service
Air Supply
Use a clean lubricated air supply that will give a measured air
pressure at the tool of 90 p.s.i./6.3 bar when the tool is running
with the trigger fully depressed. Use recommended hose size
and length. It is recommended that the tool is connected to the
air supply as shown in figure 1. Do not connect the tool to the air
line system without incorporating an easy to reach and operate
air shut off valve. The air supply should be lubricated. It is strongly
recommended that an air filter, regulator, lubricator (FRL) is used
as shown in Figure 1 as this will supply clean, lubricated air at the
correct pressure to the tool. Details of such equipment can be
obtained from your supplier. If such equipment is not used then
the tool should be lubricated by shutting off the air supply to the
tool, depressurising the line by pressing the trigger on the tool.
Disconnect the air line and pour into the intake bushing a
RPM
Cycles Per Min
3,500
Serial No
Recommended Max.
Hose Length
30
10
Ft
M
13.0
Metres / Sec²
Advertisement
Table of Contents
Related Manuals for Universal Tool UT8612-B
Summary of Contents for Universal Tool UT8612-B
- Page 1 Universal Air Tool Company Limited Cycles Per Min Unit 8 3,500 Lane End Industrial Park Model No/Nos Serial No High Wycombe UT8612-B Round Shank Bucks UT8613-B Hex Shank HP14 3BY Tel No (01494) 883300 Fax No (01494) 883237 Recommended Max.
- Page 2 teaspoonful (5ml) of a suitable pneumatic motor lubricating oil the 'off' position when it is released. preferably incorporating a rust inhibitor. Reconnect tool to air 12) Always shut off the air supply to the tool, and depress the supply and run tool slowly for a few seconds to allow air to trigger/lever etc.
- Page 3 UT8612-B 0.401” Shank Air Hammer (Round Shank) UT8613-B 0.401” Shank Air Hammer (Hex Shank) Ref No Part No Description 729006 Pin (2) 729439 Trigger 729871 Ball Seat 1001391 Ball 732504 O-Ring (2) 105021 Handle 104024 Regulator 104025 Push Rod 104026...
- Page 4 Unit 8, Lane End Industrial Park, High Wycombe, Bucks, HP14 3BY, England declare under our sole responsibility that the product Models UT8612-B & UT8613-B Air Hammer, Serial Number to which this declaration relates is in conformity with the following standard(s) or other normative document(s) EN792 (Draft), EN292 Parts 1 &...
Need help?
Do you have a question about the UT8612-B and is the answer not in the manual?
Questions and answers