Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for EK-Quantum Vector Red Devil RX 6800
Summary of Contents for EK-Quantum Vector Red Devil RX 6800
- Page 1 EK-Quantum Vector Red Devil RX 6800/6900 GPU WATER BLOCK USER GUIDE...
- Page 2 Before you start using this product, please follow these basic guidelines: Carefully read the manual before beginning with the installation process. Remove your graphics card from the computer for the safest mounting process to prevent any possible damage to your GPU or its circuit board (PCB).
-
Page 3: Table Of Contents
TABLE OF CONTENTS BOX CONTENTS WATER BLOCK DIMENSIONS TECHNICAL SPECIFICATIONS AND PRODUCT PARTS PREPARING YOUR GRAPHICS CARD REMOVING THE STOCK BACKPLATE REMOVING THE STOCK COOLER CUTTING AND PLACING THERMAL PADS CLEANING THE PCB APPLYING THERMAL COMPOUND INSTALLING THE WATER BLOCK PLACING THE BLOCK ON THE GRAPHICS CARD ATTACHING THE BLOCK TO THE GRAPHICS CARD CHECKING THE CONTACT IN CASE OF HIGH TEMPERATURES... -
Page 4: Box Contents
Universal Mounting Mechanism – You may not need every screw from this package. EAN: 3831109834688 M2.5x4 AX1 Screw (30 pcs) PVC Washer M2.5 (28 pcs) EK-Quantum Vector Red Devil RX 6800/6900 M2.5 Nut (6 pcs) Thermal Grease (1 pc) Allen Key 2 mm (1 pc) -
Page 5: Water Block Dimensions
WATER BLOCK DIMENSIONS 284.5 mm 193.9 mm 18.4 mm 164.9 mm 16.9 mm - 5 -... -
Page 6: Technical Specifications And Product Parts
TECHNICAL SPECIFICATIONS AND PRODUCT PARTS Technical Specification: - Dimensions: (L x H x W) – 284.5 x 150.5 x 18.5 mm - D-RGB cable length: 500 mm - D-RGB LED count: 9 - D-RGB connector standard 3-pin (+5V, Data, Blocked, Ground) Position EAN Description Quantity... -
Page 7: Preparing Your Graphics Card
PREPARING YOUR GRAPHICS CARD You will need the following tool: BACKPLATE Phillips Head Screwdriver STEP 1 REMOVING THE STOCK BACKPLATE Use the Phillips head screwdriver to unscrew the twelve (12) marked screws. Evenly untighten four (4) retention bracket screws for easier RETENTION BRACKET disassembly. -
Page 8: Cutting And Placing Thermal Pads
STEP 3 CLEANING THE PCB Wipe off the remains of the original thermal compound using a nonabrasive cloth or Q-tip, as shown in the sample image, until the components and circuit board are completely clean. EK recommends the use of denatured alcohol for removing TIM leftovers. After that, remove all remaining stock thermal pads from the PCB. -
Page 9: Applying Thermal Compound
STEP 2 Once cut to size, thermal pads should be placed on the PCB, as illustrated below. EK made sure to provide you with more than an adequate quantity of thermal pads to complete this Step. STEP 2 Thermal Pad F 1.0 mm APPLYING THERMAL COMPOUND STEP 1 Apply the enclosed EK-TIM Ectotherm thermal grease (thermal... -
Page 10: Installing The Water Block
INSTALLING THE WATER BLOCK STEP 1 PLACING THE BLOCK ON THE GRAPHICS CARD This procedure is the same for all full-cover water blocks. Carefully position the water block with preinstalled standoffs on the graphics card. During this process, make sure you have aligned mounting holes of the PCB with holes of the water block (same applies to other tops). -
Page 11: Checking The Contact In Case Of High Temperatures
CHECKING THE CONTACT IN CASE OF HIGH TEMPERATURES If necessary, temporarily remove the water block to check for uniform surface contact between the block and components. Pay special attention to the VRM section of the graphics card. Check whether the water block makes contact with the intended integrated circuit. -
Page 12: Installation Of Fittings And Tubing
INSTALLATION OF FITTINGS AND TUBING STEP 1 Screw in two (2) G1/4 threaded male fittings. Attach the liquid cooling tubes and connect the water block(s) to the cooling loop. Do not forget to plug the remaining two openings with enclosed EK-Plug G1/4 or its equivalent. EK- PLUG EK recommends using EK fittings with all EK water blocks. -
Page 13: Testing The Loop
TESTING THE LOOP To ensure the installation of EK components was successful, we recommend you perform a 24-hour leak test. When your loop is complete and filled with coolant, connect the pump to a PSU outside your system. Do not connect power to any of the other components. -
Page 14: Support And Service
SUPPORT AND SERVICE In case you need assistance or wish to order spare parts or a new mounting mechanism, please contact: https://www.ekwb.com/customer-support/ For spare parts orders, refer to the page with “TECHNICAL SPECIFICATIONS AND PRODUCT PARTS” where you can find the EAN number of each part you might need.
Need help?
Do you have a question about the Vector Red Devil RX 6800 and is the answer not in the manual?
Questions and answers