1. Manuals
  2. Brands
  3. SecEng Manuals
  4. Microphone system
  5. SED-901
  6. Manual

SecEng SED-901 Manual

Remote & master wireless wiegand / cardax system
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
SED-901
Remote & Master
Wireless Wiegand / Cardax System
SEP 2014
WARNING: PLEASE READ
INSTALLATION INSTRUCTIONS
FIRST
PRODUCT WARRANTY
This product is covered by a 12 month, back to base warranty from date of purchase,
and proof of purchase should be supplied. The warranty does not cover damage that
has resulted in the improper installation or improper use of this product.
The warranty does not cover lightning damage, product misuse, electrical surges or acts of God.
LIMITATION OF LIABILITY
Sec Eng Systems Pty Ltd does not accept any liability for the loss or damage to property
or persons in relation to goods supplied. This disclaimer is only limited to the warranty
of the goods supplied and the intended use.
NOTE: THIS MANUAL IS SUBJECT TO COPYRIGHT

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SED-901 and is the answer not in the manual?

Questions and answers

Related Manuals for SecEng SED-901

Summary of Contents for SecEng SED-901

  • Page 1 SED-901 Remote & Master Wireless Wiegand / Cardax System SEP 2014 WARNING: PLEASE READ INSTALLATION INSTRUCTIONS FIRST PRODUCT WARRANTY This product is covered by a 12 month, back to base warranty from date of purchase, and proof of purchase should be supplied. The warranty does not cover damage that has resulted in the improper installation or improper use of this product.
  • Page 2 3. If you are installing multiple SED-901 systems in one location, call us, so we can assist you with the best possible installation process and set up. 4. The SED-901 MASTER / REMOTE is ready to use out of the box - there is NO PROGRAMMING REQUIRED.

  • Page 3: Access Control

    INSTALLATION - START HERE INTRODUCTION The SED-901 wireless Wiegand / Cardax system is a combination of 2 devices - SED-901 Master and SED-901 Remote. This allows Wiegand / Cardax card and control information to pass over a 915 MHz low power link...

  • Page 4: Wiegand Readers

    INSTALLATION - SED 901 Wiegand Remote SED-901 MASTER Board Layout & Connections Note: The SED-901 has dual markings for MASTER & REMOTE MODE Wiegand POWER COPY PROG TEST RS232 CHARGE @115k in CTx1 LINK readers CRx1 MEMORY xxxx Reader CTx2...

  • Page 5: Dip Switches

    INSTALLATION - SED-901 Wiegand Master SED-901 MASTER Board Layout & Connections Note: The SED-901 has dual markings for MASTER & REMOTE MODE POWER COPY PROG TEST RS232 CHARGE @115k in CTx1 LINK CRx1 OUTPUT XXXX MEMORY CTx2 DATA LEDS CRx2...
  • Page 6 INSTALLATION - SED-901 Cardax Remote SED-901 MASTER Board Layout & Connections Note: The SED-901 has dual markings for MASTER & REMOTE Cardax MODE POWER COPY PROG TEST RS232 CHARGE readers @115k in CTx1 LINK xxxx Reader CRx1 MEMORY blue beep...
  • Page 7 INSTALLATION - SED 901 Wiegand Master SED-901 MASTER Board Layout & Connections Note: The SED-901 has dual markings for MASTER & REMOTE MODE POWER COPY PROG TEST RS232 CHARGE @115k in CTx1 LINK CRx1 Output XXXX MEMORY WHITE CTx2 Data...

  • Page 8: Address Switch

    SED-901 MASTER GUIDE LED’S Power LED = power on Charge LED indicates battery charging (if fitted) Power Link LED indicates that it can see RF link Charging Memory LED indicated SD card fitted CTX1 Link TX = packet being transmitted...
  • Page 9 The SED-901 system can support expanders Set up Please Read 1/ Ensure you set the mode switch on the SED-901 on your expander 2/ Set the address switch according to the number of expanders you have hanging off each SED-901 Remote or SED-901 Master see below...
  • Page 10 INSTALLATION - SED-901 Expander Programming The Sed 901 Master & Remote Expanders To enrol a board for self learning 1/ Ensure they are all wired and configured and set up also check dip switches 2/ On the ( Master Expander ) board the press the Copy & Prog buttons...
  • Page 11 SED-901 MASTER GUIDE AC Power in 16V AC 1.5A Battery in 12V Backup battery 7 AH gel cell (do not wire 12V DC into this) RS485 Port (not used for coms) RF Link Relay Relay is active when the Master and Remote units are within range and linked...
  • Page 12 On the SED-901 Remote - the signal light should be ON This means that the link is established and functioning Test an alarm input on the SED-901 Master Relay Board, this should trigger a relay on the SED-901 Remote. Wiring the SED-901 MASTER...

  • Page 13: For Technical Support

    SED-901 TESTING GUIDE NOTE: both the 900 MHz radio units require line of sight signal, they will work through buildings, however, this may effect signal coverage. Position the Remote at the location where you require to install it and do a field test to...
  • Page 14 SED-901 TECHNICAL SPECS Each RF module is compliant under the following: DECLARATION OF CONFORMITY MANUFACTURER’S NAME/ADDRESS: Max Stream, Inc 355 South 520 West Suite 180 Lindon, UT 84058 USA LABORATORIES: UltraTech EMC Labs Inc. {ITI (UK)) accredited test facilities} 3000 Bristol Circle Oakville, Ontario, Canada L6H 6G4 EQUIPMENT TYPE/ENVIRONMENT: Radio Communications Equipment TRADE NAME / MODEL NO.:...

Table of Contents