Table of Contents
Advertisement
Quick Links
Thank you for choosing the AVS range of LCD monitors. Please ensure installation is carried out by a suitably qualified technician using
industry best practice. All connections to 12/24v should be appropriately fused.
IMPORTANT: Where wiring diagram shows an ACC connection the wire MUST be connected to ACC DO NOT connect to ignition or
constant 12v.
AVS RM43
WIRE COLOUR
FUNCTION
RED (ACC)
+12v ACC supply
BLACK
Earth
YELLOW RCA
AV2 camera input
WHITE RCA
AV1 camera input
REAR BUTTON
FUNCTION
TOP
Adjust display brightness/contrast up
MIDDLE
MENU – push to enter menu and scroll through functions
BOTTOM
Adjust display brightness/contrast display brightness/contrast down
AVS RM50SM
WIRE COLOUR
FUNCTION
RED (ACC)
+12v ACC supply
BLACK
Earth
PURPLE
Switches to IN2 input
when 12v applied.
Switches off or back
to IN1 (if signal
present on IN1) when
12v removed.
IN1
Video input
Displays input when
video signal is
detected
IN2
Video input
controlled by purple
wire
REAR BUTTON
FUNCTION
TOP
Adjust display brightness/colour up
MIDDLE
MENU – push to enter menu and scroll through functions
BOTTOM
Adjust display brightness/ colour display brightness/contrast down
AVS RM50SM WIRING DIAGRAM
AVS RM SERIES LCD MONITORS – INSTALL GUIDE
AUGUST 2017
CONNECT TO
Appropriately fused +12v switched ACC supply
Good earth source e.g. vehicle body/chassis
Reverse camera output. Monitor will auto switch to display this input when a signal is
detected e.g. when the car goes into reverse and powers on the camera. The display will
switch back to AV1 or turn off if there is no signal on AV1.
Camera output. Monitor will display AV1 until a signal is detected on AV2.
CONNECT TO
Appropriately fused +12v switched ACC supply
Good earth source e.g. vehicle body/chassis
Connect to 12v switching output eg reverse light.
Connect to switched video source eg reverse camera.
Connect to video source. Monitor will display video when a 12v signal is detected on
purple wire.
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for AVS RM Series
Summary of Contents for AVS RM Series
- Page 1 AVS RM SERIES LCD MONITORS – INSTALL GUIDE AUGUST 2017 Thank you for choosing the AVS range of LCD monitors. Please ensure installation is carried out by a suitably qualified technician using industry best practice. All connections to 12/24v should be appropriately fused.
- Page 2 Camera output. Monitor will display V1 until a signal is detected on V2 or switch off if no signal on V1. AVS RM43B WIRING DIAGRAM When connecting the power cable please ensure the positive and negative poles are correct otherwise the fuse will blow to protect the unit.
- Page 3 Good earth source e.g. vehicle body/chassis GREEN Switches display to V2 Reverse signal/vehicle reverse light wire (+12v). Use red wire on AVS Camera’s RCA lead FEMALE RCA V2 camera input Reverse camera output. Monitor will auto switch to display this input when a signal is detected e.g.
- Page 4 AVS RM90C The AVS RM90C can display up to 4 cameras in a split screen, either any channel full screen, 2 way or 4 way split. The channels can be switched manually using the buttons on the front panel or remote or can be controlled by each channels input wire e.g.
- Page 5 MODE OPTIONS DISPLAYS FULL SCREEN CH1, 2, 3 or 4 - full screen DUAL SPLIT CH1 & CH2 or CH3 & CH4 3 WAY SPLIT EVEN CH1 & CH2 & CH3 3 WAY SPLIT LEFT CH 3 half screen + CH1 & CH2 3 WAY SPLIT RIGHT CH1 &...
Need help?
Do you have a question about the RM Series and is the answer not in the manual?
Questions and answers