Page 15
一般计时记录 (例:100米赛跑) 按钮 循以下次序按下按钮: 按钮 A 按钮 B 按钮 0 1 2 (开始) (结束) (重设) 按钮 累积时间记录(例:篮球比赛) 按钮 A 按钮 A 按钮 A 按钮 A 按钮 B (开始) (结束) (再开始) (重设) * 可随需要多次按下按钮A以重新开始及停止秒表功能...
Page 16
分段时间记录 (例:5,000米接力赛) 按钮 A 按钮 B 按钮 A 按钮 B 按钮 (开始) (记录分段时间) (下一分段计时) (结束) (重设) * 可随需要多次按下按钮B以作多次分段计时 按钮 0 1 2 按钮...
Page 22
INTRODUCTION Thank you very much for choosing INFANTRY watch. For proper and safe use of your INFANTRY watch, Please read carefully for the instructions in this booklet before using The Following booklet is suitable for Infantry model below: 1. WATCH WITH TIME, DAY AND DATE 2.
ABOUT WARRANTY Within one year from the date of purchase, we guarantee free repair/adjustment service against any defects according to the following guarantee regulations, provided that the watch was properly used as directed in this instruction booklet Exceptions from warranty: 1: Troubles or damage caused by accidents or improper usage 2: Scratches or grime caused by use (Watch Case, Straps, Crown)
PRODUCT SPECIFICATION Operation temperature range: −10℃ ~ +50℃ Water Resistant: 10 ATM Product operation standard: GB/T 6044 Production level: Top Grade Caution: Usage of exceeding the operation temperature range may result in damaging the watch movement.
Page 25
WATCH WITH INR-AD-Z1 WATCH MOVEMENT TIME SETTING (DIGITAL) Under Normal Time Display Mode: 1. Press S2 until the display screen start flashing, then press S4 to until it switch to the desired parameter (Minute, Hour, Day, Month, Week) 2. Press S3 to adjust the desired item.
Page 26
CHRONOGRAPH The display range of the chronograph is 23 hours 59 minutes, 59.99 seconds. Under Normal Time Display Mode: Press S2 one time to enter chronograph mode Event Mode: S3---Start, S3---Stop (Repeat S3, Time In/Out), S4---Reset Split Mode: S3---Start, S4---Split, S4---Release (Repeat S4 for each split), S3---Stop, S4---Reset...
Page 27
ALARM Under Normal Time Display Mode: 1. Press S2 two times to enter alarm setting mode. 2. Press S4 until it switch to the desired parameter. 3. Press S3 to select desire value accordingly. 4. Press S4 to finish setting alarm. Under Normal Time Display Mode: 1.
Page 28
WATCH WITH TMI-VD57C WATCH MOVEMENT ADJUSTING THE STOPWATCH HAND POSITION * Before setting the time, check if all the chronograph hands - 1/10 second (where applicable), second, minute - are at the "0"(12 o'clock) position. 0 1 2 * If the stopwatch is in use, press the buttons in the following order to reset it, and then, check if the hands return to "0"...
Page 29
If either of the stopwatch hands are not in the "0" position , reset them following the procedure below. 1) Pull the crown out to the second click 2) Press button A or B to reset all 0 1 2 stopwatch hands to "0"...
TIME SETTING Before setting the time, check that the chronograph measurement is stopped. 1) Pull out the crown to the first click. 2) Turn the crown clockwise until the 0 1 2 preview day's date appears. 3) Pull out the crown to the second click when the second hand is at the 12 o'clock position.
Page 31
* When the crown is at the second click position, do not press any button. Otherwise the chronograph hands 0 1 2 will move. 4) Push the crown back in the normal position in accordance with a time signal. * Do not set the date between 9:00 P.M. and 1:00 A.M, otherwise the day may not change properly.
Page 32
1) Pull out the crown when the second hand is at the 12 o'clock position. The second hand will stop on the spot. 2) Set the hands to the desired time of 0 1 2 the day by turning the crown * Do not press any button, otherwise the chronograph hands will move.
HOW TO USE THE STOPWATCH * The measurement time is indicated by the stopwatch hands that move independently of the center hands (and 24-hour hand where 0 1 2 applicable). * The stopwatch can measure up to 60 minutes * The stopwatch measures in 1/10 second increments.
Page 34
Standard measurement (e.g. 100m race) Press the buttons in the following order : Button A Button A Button A Button A Button B (START) (STOP) (RESTART) (STOP) (RESET) * Restart and stop of the stopwatch can be repeated as many times as necessary by pressing button A.
WATCH WITH INR-X1-SK MOVEMENT SETTING THE TIME 1. Pull out the crown to position 1. 2. Turn the crown until the correct time appears. 3. Push the crown back into position 0. WIND UP 1. Stay the crown at position 0. 2.
WATCH WITH INR-X1 MOVEMENT SETTING THE TIME AND DATE 1. Pull out the crown to position 1. *Wind it daily to 2. Turn the crown until you reach the correct date. make sure it has 3. Pull out the crown to position 2. consistent power 4.
The daily time difference of a top grade quartz movement watch is +/- 0.5 second. Our company internal standard guarantee our “Infantry” quartz watch monthly time differences is +/- 20 seconds.
WATER RESISTANCE INFANTRY REVOLUTION SERIES is well known to meet the standard of 10 ATM. ATM or “atmospheres” is the amount of pressure a watch can withstand before leaking. A 10 ATM watch will withstand pressures equivalent to about 100 METERS, or 330 FT under water.
Page 39
10 ATM-Water resistant to 100metres (330ft). Suitable for recreational surfing, swimming, snorkeling, sailing and water sports. Not suitable for diving. 3 ATM watch is not suitable to be used in warm or hot water environment, as hot temperature will accelerate the water resistant material of the watch.