Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Hafco MS3816
Summary of Contents for Hafco MS3816
- Page 1 HOLLOW CHISEL MORTISER MODEL MS3816...
-
Page 2: General Safety Rules
14. MAINTAIN TOOLS IN TOP CONDITION. Keep tools sharp and clean for best and safest performance. Follow instructions for lubricating and changing accessories. 15. DISCONNECT TOOLS before servicing and when changing accessories such as blades, bits, cutters, MS3816 Hollow Chisel Mortiser １ V.02 01-11-2010... - Page 3 Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles. MS3816 Hollow Chisel Mortiser ２ V.02 01-11-2010...
- Page 4 21. TURN THE MACHINE “OFF”, disconnect the machine from the power source, and clean the table/work area before leaving the machine. LOCK THE SWITCH IN THE “OFF” POSITION to prevent unauthorized use. MS3816 Hollow Chisel Mortiser ３ V.02 01-11-2010...
-
Page 5: Power Connections
Repair or replace damaged or worn cord immediately. WARNING: IN ALL CASES, MAKE CERTAIN THE RECEPTACLE IN QUESTION IS PROPERLY GROUNDED. IF YOU ARE NOT SURE, HAVE A QUALIFIED ELECTRICIAN CHECK THE RECEPTACLE MS3816 Hollow Chisel Mortiser ４ V.02 01-11-2010... -
Page 6: Unpacking And Cleaning
ON LY AN D MA Y NO T D EPIC T THE AC TUA L COLOR , LAB ELIN G O R ACCESSORIES AND MAY BE INTENDED TO ILLUSTRATE TECHNIQUE ONLY. HOLLOW CHISEL MORTISER PARTS Fig. MS3816 Hollow Chisel Mortiser ５ V.02 01-11-2010... -
Page 7: Operating Controls And Adjustments
2. Raise mortising machine head (A) Fig. 3, to the up position by turning handle (B) clockwise. OPERATING CONTROLS AND ADJUSTMENTS RAISING AND LOWERING THE HEAD The head (A) Fig. 4, is raised and lowered by means of the lever (B). MS3816 Hollow Chisel Mortiser ６ V.02 01-11-2010... -
Page 8: Depth Stop
A depth stop guide (A) Fig. 6, is provided to limit the depth of the chisel (B). To adjust the depth stop guide (A), loosen handle (C) and lower head until the chisel (B) is at the desired depth. Lower depth stop guide (A) until it is at the desired depth, tighten handle (C). MS3816 Hollow Chisel Mortiser ７ V.02 01-11-2010... - Page 9 2. Sharpen the chisel with a mortise chisel cutter with the correct size pilot. (Pilot size will differ depending on the size of your chisel). Two or three turns of the cutter in a carpenter's brace chuck should be enough to sharpen the chisel, as shown in Fig. 9. MS3816 Hollow Chisel Mortiser ８ V.02 01-11-2010...
- Page 10 Fig 9 Fig 10 3. Use a small, triangular, smooth file to relieve the inner corners of the chisel. See Fig.10. Remove any burrs from the outside of the chisel with a fine oilstone. MS3816 Hollow Chisel Mortiser ９ V.02 01-11-2010...
- Page 11 Parts Diagram for MS3816 MS3816 Hollow Chisel Mortiser １０ V.02 01-11-2010...
- Page 12 PART LIST For MS3816 Part NO. DESCRIPTION Q’TY Part NO. DESCRIPTION Q’TY Handle Table Motor Clamp Plate Switch Box Screw Screw Gear Shaft Screw Screw Screw Handle Screw Setting Collar Screw Guide Column Rack Screw Sliding Plate Localizer Washer Screw...
- Page 13 MS3816 Hollow Chisel Mortiser １２ V.02 01-11-2010...
Need help?
Do you have a question about the MS3816 and is the answer not in the manual?
Questions and answers