Advertisement
Examples of Mounting
Detector
Detector
Battery Life and Replacement
Battery life depends on environmental temperature and how often sensor transmits signals. Sensor transmits a low battery indication
to panel when it detects the battery voltage is low. Replace both batteries as soon as possible.
• Depress cover latch on top edge and lower cover.
• Remove both batteries from their holders and install two (2) new batteries observing (+) polarity marked on the batteries and
the circuit board.
CAUTION: Battery may explode if mistreated. Do not recharge, disassemble, incinerate or expose to heat above 212° F
(100° C). Keep away from children.
Battery Disposal: The batteries used in this sensor are lithium batteries and are not reuseable. Dispose of used lithium
batteries according to your local hazardous waste disposal laws.
FCC AND IC COMPLIANCE STATEMENT:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this
device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired
operation of the device.
Cet appareil est conforme avec Industrie Canada exempts de licence standard RSS (s). Son fonctionnement est soumis aux deux conditions
suivantes: (1) cet appareil ne doit pas provoquer d'interférences et (2) cet appareil doit accepter toute interférence, y compris celles pouvant
causer un mauvais fonctionnement de l'appareil.
In accordance with FCC requirements of human exposure to radio
frequency fields, the radiating element shall be installed such that a minimum separation distance of 20 cm is maintained from the general
population.
FCC ID: 2ABBZ-RF-GB-319
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes
or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
This Class B digital apparatus complies with Canadian ICES-3B.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
LIMITED WARRANTY: THIS WIRELESS SENSOR IS WARRANTED TO BE FREE FROM DEFECTS AND WORKMANSHIP FOR A PERIOD
OF 2 YEARS FROM DATE OF MANUFACTURE EXCLUDING BATTERIES. BATTERIES USED WITH WIRELESS DEVICES ARE NOT
WARRANTED. MANUFACTURER HEREBY DISCLAIMS ANY AND ALL OTHER WARRANTIES AND REPRESENTATIONS, WHETHER
EXPRESS, IMPLIED, STATUTORY OR OTHERWISE INCLUDING (BUT NOT LIMITED TO) ANY WARRANTIES OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE WITH RESPECT TO THESE PRODUCTS AND ANY RELATED SOFTWARE. MANUFACTURER
FURTHER DISCLAIMS ANY OTHER IMPLIED WARRANTY UNDER THE UNIFORM COMPUTER INFORMATION TRANSACTIONS ACT OR
SIMILAR LAW AS ENACTED BY ANY STATE. (USA only) SOME STATES DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES,
SO THE ABOVE EXCLUSION MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO
HAVE OTHER LEGAL RIGHTS THAT VARY FROM STATE TO STATE. MANUFACTURER MAKES NO REPRESENTATION, WARRANTY,
COVENANT OR PROMISE THAT ITS ALARM PRODUCTS AND/OR RELATED SOFTWARE (I) WILL NOT BE HACKED, COMPROMISED
AND/OR CIRCUMVENTED; (II) WILL PREVENT, OR PROVIDE ADEQUATE WARNING OR PROTECTION FROM, BREAK-INS, BURGLARY,
ROBBERY, FIRE; OR (III) WILL WORK PROPERLY IN ALL ENVIRONMENTS & APPLICATIONS.
NOTE: Elk Products is not responsible for any changes or modifications not expressly approved by the party responsible for
compliance. Such modifications could void the user's authority to operate the equipment.
Elk Products, Inc.- 3266 Hwy 70 - Connelly Springs, NC 28612
Fig. 1 Ceiling
mount for
windows on
adjacent walls
Fig. 4 Ceiling
mount for
windows on
the same wall
IC: 11817A-RFGB319
Fig. 2 Wall
Detector
mount for
windows on
the same wall
Fig. 5 Detector
Detector
mount between
window and
curtains (louvers)
http://www.elkproducts.com
Fig. 3 Wall
Detector
mount for
windows on
opposite wall
Detector
Fig. 6
Places not
recommended
for mounting
of detector
9/8/20
Advertisement
