Table of Contents
Advertisement
Quick Links
K&K Single point swing # 040720001 - Instruction
1x [1060844]
Cross section incl. bearing of Pendulum Swing
4x [1060695]
Support Pendulum
Swing
Kaiser & Kühne Freizeitgeräte GmbH
Im Südloh 5 - 27324 Eystrup
K&K Single point swing # 040720001
1x [1060701]
Seat and Chain for Pendulum
Swing incl. 4x chains and 1x
swing seat
Page 1 of 16
Play level mark (= pin)
conforms to the mounting
depth of swing post
+49 4254 93150
info@kaiser-kuehne-play.com
Advertisement
Table of Contents
Summary of Contents for Kaiser & Kühne Pendulum Swing
-
Page 1: K&K Single Point Swing # 040720001
K&K Single point swing # 040720001 - Instruction Page 1 of 16 K&K Single point swing # 040720001 1x [1060844] Cross section incl. bearing of Pendulum Swing Play level mark (= pin) conforms to the mounting depth of swing post... -
Page 2: Table Of Contents
K&K Single point swing # 040720001 - Instruction Page 2 of 16 K&K Single point swing # 040720001 Instruction Spaces and areas Equipment installation Foundation Final assembly Instructions for professional inspection and maintenance of single-point swings One-time maintenance work Regular maintenance Routine visual inspection Operational inspection Annual main inspection... -
Page 3: Instruction
K&K Single point swing # 040720001 - Instruction Page 3 of 16 Instruction 1. Assign location of equipment considering the minimum space requirements (impact area). 2. Excavate soil for foundations, according to drawing. Please note: To achieve maximum stability and a safe installation, a moderate level of soil solubility is required. 3. -
Page 4: Spaces And Areas
K&K Single point swing # 040720001 - Instruction Page 4 of 16 6,45 play level Impact area Spaces and areas *54 m² resp. **68 m² Area to be covered by impact absorbing surface under each swing position. free height of fall = 2,25 m play level mark 0,75 *) measure for synthetic surfacing with impact attenuating ef-... -
Page 5: Equipment Installation
K&K Single point swing # 040720001 - Instruction Page 5 of 16 Equipment installation At first, mount two opposite swing posts to the junction, according to drawing. Raise the unit by using an appropriate lifting gear. Afterwards, mount the remaining two posts to the junction, place the whole unit into the foundation holes and align item horizontally considering the play level marks on the inner surface of the swing posts for installation depth. -
Page 6: Foundation
K&K Single point swing # 040720001 - Instruction Page 6 of 16 Foundation Foundations (on site) 4x 0,75 x 0,75 x 0,70 m (approximate) concrete needs 1,6 m³ play level concrete C20/25 0,75x0,75 gravel +49 4254 93150 Kaiser & Kühne Freizeitgeräte GmbH Im Südloh 5 - 27324 Eystrup info@kaiser-kuehne-play.com... -
Page 7: Final Assembly
Final assembly After concrete foundations have set, attach chains to the swivel of the universal joint of swing axle. Swivel of the universal joint Seat and Chain for Pendulum Swing dog point screw U-Link (M16-stainless steel) with installation paste Chain The swivel is ex works ready filled with grease lubricant. -
Page 8: Instructions For Professional Inspection And Maintenance Of Single-Point Swings
K&K Single point swing # 040720001 - Instruction Page 8 of 16 K&K Single point swing # 040720001 Instructions for professional inspection and maintenance of single-point swings Playground equipment is subject to a wide range of stresses and strains over the course of its useful life, which can reduce or even eliminate the original safety. -
Page 9: One-Time Maintenance Work
K&K Single point swing # 040720001 - Instruction Page 9 of 16 One-time maintenance work Four weeks after installation, all screw connections must be checked and tightened if necessary. In this case, the specified advice in the regular maintenance work e. g. to turning moments has to be observed. -
Page 10: Annual Main Inspection
K&K Single point swing # 040720001 - Instruction Page 10 of 16 2-2. every 3 months (or different, determined by local factors) • Check axles, hubs and bearings for smooth running, bearing shake, wear or corrosion. • Check for bearing play and wear. To check, the swing platform and the univer- sal joint must be relieved by lifting the platform (e.g. -
Page 11: Endurance Of The Rotating Swivel
K&K Single point swing # 040720001 - Instruction Page 11 of 16 4. Endurance of the rotating swivel • Dismount the swing joint of the playground equipment at the latest after a service life of 10 years and send it to the manufacturer/distributor for revi- sion. -
Page 12: Appendix A1
K&K Single point swing # 040720001 - Instruction Page 12 of 16 Appendix A1 Visual inspection of swivel at least once a month: Check for visibility of the red-coloured warning groove Warning groove Warning groove (red-coloured) NOT (red-coloured) VISIBLE VISIBLE Lock the play equipment imme- diately - send the swing joint to the factory for repair! -
Page 13: Appendix A2
K&K Single point swing # 040720001 - Instruction Page 13 of 16 Appendix A2 Replace lubrication at least every 6 months required equipment: • Lever grease press for taper lubricating nipple (K&K item 5200732) • Fluid grease for K&K swing joints (K&K item 5200733) •... -
Page 14: Annexion E1
Page 14 of 16 Annexion E1 Spare parts Item no. Quan- Description Image tity 1060695 Support Pendulum Swing 1060844 Cross section incl. bearing of Pendu- lum Swing 1060829 Universal joint with swivel (four chain strands) 3400557 Cheese head screw M16x80 3430060 Washer Ø17... - Page 15 Annexion E1 Spare parts Item no. Quan- Description Image tity 1060701 Seat and Chain for Pendulum Swing incl. 4x chains and 1x swing seat 3590050 Single point swing seat 015753 4x 2214 Stainless steel chain Ø 7,0 mm 1060742 U-Link 6 mm for 015818/3590050...
- Page 16 K&K Single point swing # 040720001 - Instruction Page 16 of 16 Annexion E1 Spare parts Item no. Quan- Description Image tity 3430019 Washer Ø 17mm 3430053 Hexagon cap nut M16 5200733 Fluid grease cartridge 400 g 5200732 Lever grease press 3490006 Allen key security hex socket AF5 2030204...