Philio PSE04 Quick Start Manual

Multiple sound siren

Advertisement

Quick Links

Multiple Sound Siren PSE04
Built-in high accuracy Temperature sensor
The PSE04 is a wireless siren, based on Z-Wave
Z-Wave Plus
TM
product, it support the security, OTA... Those newest
features of the Z-Wave
TM
communication protocol designed for home automation, specifically to
remotely control applications in residential and light commercial
environments. The technology uses a low-power RF radio embedded or
retrofitted into home electronics devices and systems, such as lighting,
home access control, entertainment systems and household appliances.
This product can be included and operated in any Z-Wave
with other Z-Wave
TM
certified devices from other manufacturers and/or
TM
technology. It is the
technology. Z-Wave
TM
is a wireless
other applications. All non-battery operated nodes within the network
will act as repeaters regardless of vendor to increase reliability of the
network.
The device adopt the Z-Wave
network system is all made by Z-Wave
network system will have the advantages as below.
Concurrent multi-channel support reduces external interference.
Better RF range, improve about 10 meters in indoor.
Support 100 Kbps transmit speed, speed up communication.
Specification
Rating
RF distance
RF Frequency
RF Maximum Power
Dimension
Weight
IP classification
Operation temperature
Humidity
FCC ID
TM
network
Marking
1
TM
700 series chip, when your Z-Wave
TM
700 series devices. The
6VDC (AA Battery *4)
Min. 40M indoor,
100M outdoor line of sight,
868.40 MHz, 869.85 MHz(EU)
908.40 MHz, 916.00 MHz(US)
920.9MHz, 921.7MHz, 923.1MHz
(TW/KR/Thai/SG)
921.40 MHz, 919.80 MHz(ANZ)
869.00 MHz(RU)
865.20 MHz(IN)
916.00 MHz(IL)
+10dBm (Peak), -10dBm
(Average)
170mm(L) X 48mm (W) X 30(H)
205g
IP44; Outdoor use
-20 to 55° C
85%RH max
RHHPSE04
CE/NCC
TM

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the PSE04 and is the answer not in the manual?

Questions and answers

Summary of Contents for Philio PSE04

  • Page 1 RF Frequency 921.40 MHz, 919.80 MHz(ANZ) Built-in high accuracy Temperature sensor 869.00 MHz(RU) 865.20 MHz(IN) The PSE04 is a wireless siren, based on Z-Wave technology. It is the 916.00 MHz(IL) Z-Wave Plus product, it support the security, OTA... Those newest...
  • Page 2: Troubleshooting

    Overview  Specifications are subject to change and improvement without notice. Troubleshooting Symptom Cause of Failure Recommendation The device can not The device may in a Z- Exclude the device join to Z-Wave™ Wave™ network. then include again. network...
  • Page 3: Battery Installation

    Battery Installation When the device report the low battery message. The user should replace the battery to new one. The battery type is AA, 1.5V Please loosen the screw on the back cover to release the front cover...
  • Page 4: Function Description

    Controller entered inclusion mode. *notice1:The QR code can be found on the device 2. Pressing tamper key three times within 1.5 seconds PSE04 or on the box. to enter the inclusion mode. This machine provides one groups of nodes. Each 3.
  • Page 5: Led Light Indication

    1. Notice 1: The PSE04 must stay awake for at least 2 seconds after communicating, so therefore the more communication, the power Notification Report (V8) consumption f ast, please pay attention to use configuration NO.5.
  • Page 6: Over The Air (Ota) Firmware Update

    *Play Sound: means the minimum auto report interval will be one minute. And please Using the BASIC_SET or Sound_Switch_Tone_Play_Set to play the notice if setting this value to zero, that means disable all of the timing siren, BASIC_SET or Sound_Switch_Tone_Play_Set with Value 0xFF, the report except the low battery detection.
  • Page 7: Z-Wave Configuration Settings

    The temperature differential to Differential 0x00 0~255 effect. report. Report Notice 3: The PSE04 must stay awake for at least 2 seconds after communicating, so therefore the more communication, the power Auto Report The interval time for auto report 0x0C 0~255 configuration NO.1, NO.4,...
  • Page 8: Fcc Interference Statement

    They can take this product for Basic Highest granted Security Class environmentally safe recycling. Notification Highest granted Security Class Philio Technology Corporation Sound Switch Highest granted Security Class 8F., No.653-2, Zhongzheng Rd., Xinzhuang Dist., New Taipei City 24257, Battery Highest granted Security Class Taiwan(R.O.C)
  • Page 9 These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency en- ergy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

Table of Contents