Frigidaire Gallery FGHB2844L Installation Instructions

Installation Instructions* for French Door Bottom Freezer/Refrigerator
®
*Please refer to your Use & Care Guide for more details.
WARNING
To avoid electric shock, which can cause death or severe personal injury,
do not connect your refrigerator to an electrical power source until you
have completed Step 2 of these instructions.

NOTE
If you need to remove the doors to get your refrigerator into the house, please refer to
"Removing Doors" in the Use & Care Guide. These installation instructions are provided only as
a possible customer option. Frigidaire recommends that you use a service or kitchen contracting
professional to install your refrigerator.
IMPORTANT
CAUTION
If you are installing your refrigerator
• Shifting the refrigerator from side to side
without connecting it to a water
may damage flooring.
supply, make sure the ice maker's
• Do not block the toe grille on the lower
power switch is turned Off (see the
front of your refrigerator. Sufficient air cir-
Use & Care Guide for more details).
1
culation is essential for proper operation.
Preparing For Installation
Be sure to coordinate site preparation and installation
with your kitchen contractor. 
Include these minimum guidelines in your site preparation:
• Choose a place near a grounded electrical outlet.
• Do not use an extension cord or an adapter plug. Please call 1-877-435-3287 if you
need assistance with this installation.
• Avoid direct sunlight and close proximity to a range,
dishwasher or other heat source.
• Floor should be level and able to
support a fully loaded refrigerator.
• The refrigerator's Ice Dispenser
requires water supply access.
• Plan for easy access to counter tops
when removing food.
• For complete access to drawers and
freezer baskets, doors must be able to
fully open.
• Load refrigerator from side of cabinet only.
• Do not run retaining straps over handles nor over-tighten straps.
• Never use refrigerator handles to move the refrigerator.
Allow the following clearances for ease of installation, proper air circulation, and plumbing and
electrical connections: Sides & Top: 3/8 inch / Rear: 1 inch
2
Connect Water Supply
Before Installing The Water Supply Line, You Will Need:
• Basic Tools: adjustable wrench, flat-blade screwdriver, and
Phillips screwdriver
TM
• Access to a household cold water line with water pressure
between 30 and 100 psi.
• A water supply line made of ¼ inch OD, copper or stainless
steel tubing. To determine the length of tubing needed,
measure the distance from the ice maker inlet valve at the
back of the refrigerator to your cold water pipe. Then add
approximately 7 feet, so the refrigerator can be moved out
for cleaning.
• A shutoff valve to connect the water supply line to your
household water system. DO NOT use a self-piercing type shutoff valve.
• A compression nut and ferrule (sleeve) for connecting a copper water supply line to the ice
maker inlet valve.
CAUTION
To Avoid Property Damage:
• Copper or Stainless Steel braided tubing is recommended for the
water supply line. Water supply tubing made of ¼ inch plastic is not
recommended to be used. Plastic tubing greatly increases the poten-
tial for water leaks, and the manufacturer will not be responsible for
any damage if plastic tubing is used for the supply line.
• DO NOT install water supply tubing in areas where temperatures fall
below freezing.
• Chemicals from a malfunctioning softener can damage the ice maker.
If the ice maker is connected to soft water, ensure that the softener is
maintained and working properly.
If you are not satisfied with the installation of your refrigerator, please contact the store you purchased it from or call 1-800-944-9044 for assistance.
To Connect Water Supply Line To Ice Maker Inlet Valve
1. Disconnect refrigerator from electric power source.
2. Place end of water supply line into sink or
bucket. Turn ON water supply and flush
supply line until water is clear. Turn OFF
water supply at shutoff valve.
3. Remove plastic cap from water valve inlet
and discard cap.
4. If you use copper tubing - Slide brass
compression nut, then ferrule (sleeve) onto
water supply line. Push water supply line into
water valve inlet as far as it will go (¼ inch).
Slide ferrule (sleeve) into valve inlet and
finger tighten compression nut onto valve.
Tighten another half turn with a wrench; DO
NOT over tighten. See Figure 1.
If you use stainless steel tubing - The nut
and ferrule are already assembled on the
tubing. Slide compression nut onto valve
inlet and finger tighten compression nut
onto valve. Tighten another half turn with a
wrench; DO NOT over tighten. See Figure 2.
5. With steel clamp and screw, secure water
supply line (copper tubing only) to rear panel
of refrigerator as shown.
6. Coil excess water supply line (copper tubing
only), about 2½ turns, behind refrigerator
NOTE
as shown and arrange coils so they do not
vibrate or wear against any other surface.
7. Turn ON water supply at shutoff valve and
tighten any connections that leak.
8. Reconnect refrigerator to electrical power
source.
CAUTION
9. To turn ice maker on, lower wire signal arm
(side mounted) or set the ice maker's On/
Off power switch to the "I" position (rear
Room temperatures mounted).
below 55°F (13°C)
or above 110°F 
NOTE
(43°C) will impair
cooling ability of
your refrigerator's
Check with your local building authority for
compressor.
recommendations on water lines and associated
materials prior to installing your new refrigerator.
Depending on your local/state building codes,
Frigidaire recommends for homes with existing
valves its Smart Choice® water line kit
5305513409 (with a 6 ft. Stainless Steel Water
Line) and for homes without an existing valve,
Frigidaire recommends its Smart Choice water®
line kit 5305510264 (with a 20 ft. Copper Water
WARNING
Line with self-tapping saddle valve). Please refer
to www.frigidaire.com for more information.
To avoid electric shock,
which can cause death 3
or severe personal
injury, disconnect the Level Refrigerator & Adjust Doors (if necessary)
refrigerator from elec-
trical power before con-
Guidelines for final positioning of your refrigerator
necting a water supply
line to the refrigerator. • All four corners of the cabinet must rest firmly on the
floor.
• The sides should tilt ¼ inch from front to back (to
ensure that doors close and seal properly).
• Doors should align with each other and be level.
Most of these conditions can be met by raising or
lowering the adjustable front rollers.
To level the cabinet using the front rollers:
1 You can raise or lower each door. Use a
wrench to turn the adjustment screws (1 per side).
To raise: turn adjustment screw clockwise.
To lower: turn adjustment screw counterclockwise.
2 Ensure both doors are bind-free with their seals
touching the cabinet on all four sides and that cabinet
is stable.
3 After unit is leveled, lower anti-tip leg until it contacts
the floor.
Steel
Clamp
Plastic Water
Tubing to
Brass
Filter
Compression
Nut
Ferrule
(Sleeve)
Copper
water line
Water Valve
Bracket
Valve Inlet
Wate r V alve
Copper water line
from household water supply
(Include enough tubing in loop to allow
moving refrigerator out for cleaning.)
Figure 1
Plastic Water
Tubing
to Filter
Figure 2
Door Door
3 / inch socket
8
Raise
Anti-tip
Leg
Lower
DO NOT REMOVE this label until the refrigerator has been leveled.
Please follow all instructions for leveling your refrigerator.
Doors final adjustment using the adjustable lower hinge (select models, if
necessary):
1 Open doors to 90 degrees.
2 Remove screw.
3 Lift the door while adjusting the washer.
To raise the door: rotate washer clockwise.
To lower the door: rotate washer counter-clockwise.
4 Replace the screw, ensuring it is between the spokes of the hinge washer. Screw will not
be tight, just insert until it is flush with the hinge.
B

Remove Screw
If after adjusting doors higher the
Open
door makes a popping/clicking sound,
A
Door
90 remove screw and replace with the
degrees
longer one provided.
Bottom of Door
Raising/Lowering Door
Remove Screw
4
Leveling Freezer Drawer (if necessary)

NOTE
Drawer
Screw
DO NOT remove center screw from freezer
drawer. This is a factory adjustment.
1. Check gasket seal around top, bottom, Drawer
Screw
and sides of freezer drawer.
2. If gasket is not sealed, open drawer
and slightly loosen 4 drawer screws
(2 on each side) to allow drawer to
rotate.
3. Close drawer and recheck the seal
on the gasket (A). Open the drawer
Push Against
grabbing by the sides in the center Freezer Drawer
(B). Be careful not to rotate the
drawer.
4. Tighten 4 drawer screws.
5. Recheck gasket seal.
6. Install the toe grille by fitting into
A
place.
5
Remove Internal Shipping Materials
Frigidaire uses packing foam and tape to secure the internal parts of your refrigerator for
shipping. Once the refrigerator is in position, you can remove this material.
What's Next?
Congratulations! You are ready to begin enjoying your new Frigidaire refrigerator.
• For important safety instructions and to learn how to operate your refrigerator, please read
the entire Use & Care Guide.
• You may want to start with the "Normal Operating Sights & Sounds" section of the Guide to
learn what to expect during typical operation.
• Please register your product. You can register online at www.frigidaire.com or you can
simply send in the Registration Card.
6
 Installation Check List
Doors
Ice Maker
□
Handles are secure and tight □
House water supply connected to
□
Door seals completely to cabinet on all sides
refrigerator
□
□
Fresh food doors are level
No water leaks present at all connections
□
Leveling Ice Maker is turned ON.
□
Refrigerator is level, side to side and tilted
Final Checks
1/4" front to back
□
□
Shipping material removed
Toe grille is properly attached to refrigerator
□ □
Fresh Food and Freezer temperatures set
Cabinet is sitting solid on all corners
Electrical Power
□
House power turned on
□
Refrigerator plugged in
NOTE
Drawer
Screw
Drawer
Screw
Grab Drawer
At Center
From Both Sides
Then
Pull Drawer Out
B
P/N: 242046900