Copyright Trademarks 2007 by Samsung Electronics Co., Ltd. Samsung is the registered trademark of Samsung Electronics Co., Ltd. All rights reserved. LE19R86BD and Macmaster Cable Adapter are This manual may not, in whole or in part, be copied, trademarks of Samsung Electronics Co., Ltd.
Page 5
Asia http://asia.samsungportal.com Mideast & Africa http://mea.samsungportal.com 2007 Samsung Electronics Co.,Ltd. This Service Manual is a property of Samsung All rights reserved. Electronics Co.,Ltd. Printed in Korea Any unauthorized use of Manual can be punished under P/N : BN82-00186-00 applicable International and/or domestic law.
3 Alignments and Adjustments 3 Alignments and Adjustments 3-1 Service Instruction 1. Usually, a color TV-VCR needs only slight touch-up adjustment upon installation. Check the basic characteristics such as height, horizontal and vertical sync. 2. Use the specified test equipment or its equivalent. 3.
Page 7
3 Alignments and Adjustments 3-2 How to Access Service Mode 3-2-1 Entering Factory Mode 1. To enter "Service Mode" Press the remote -control keys in this sequence : - If you do not have Factory remote - control Power ON Power OFF INFO MENU...
3 Alignments and Adjustments 3. White Balance item Value Sub Bright Red Offset Greem Offset Blue Offset Sub Contrast Red Gain Green Gain Blue Gain 4. MST 68981 1) ADC Calibration Value item CVBS Y Gain CVBS Y Offs Ana Y Offs Ana Pb Offs Ana Pr Offs Ana Y Gain...
Page 10
3 Alignments and Adjustments 2-2) Comp ADC Target item Value High Delta 2-3) PC ADC Target item Value High Delta 2-4) AII RGB Target item Value High Delta 3) Sharpness item Value H1 Gain H2 Gain H3 Gain H4 Gain V1 Gain V2 Gain D1 Gain...
Page 11
3 Alignments and Adjustments value item Pattern Select BS-On B-Slope Gain B-Tilt Min B-Tilt Max B-Tilt Slope LFunc-Basis HFunc-Basis Mean-Offset1 Mean-Offset2 Mean Slope Input Offset Input Gain ACR Offset ACR Th1 ACR Th2 Skin Enable Skin Tu Skin Tv M Skin Tu M Skin Tv Sub Color M-Au-Sub Color...
Page 12
3 Alignments and Adjustments 6. Sound item value Saturation Mute FM Prescale AM Prescale Nicam Prescale FM M Prescale SC1 Vol SC2 Vol Audio Delay Audio Delay Time Ch1 BW Ch2 BW Num of Check Num of Double Check Mono Weight Stereo Weight Dual Weight BG M2S Threshold...
Page 13
3 Alignments and Adjustments 7. YC Delay item Value PAL BG PAL DK PAL I SECAM BG SECAM DK SECAM L NTSC 358 NTSC 443 AV PAL AV SECAM AV NT358 AV NT443 AV PAL60 8. Adjust item value V Mute Time Dynamic Contrast Dynamic Dimming Dynamic CE...
3 Alignments and Adjustments 9. Bus Stop 10. W/B Movie item value WB Movie Color Mode Movie Cool1 Color Tone Msub Brigh Msub Contr W1_RGAIN W1_BGAIN W1_ROFFS W1_BOFFS W2_RGAIN W2_BGAIN W2_ROFFS W2_BOFFS NO_RGAIN NO_BGAIN NO_ROFFS NO_BOFFS C2_RGAIN C2_BGAIN C2_ROFFS C2_BOFFS Movie Contr Movie Brigh Movie Color...
3 Alignments and Adjustments 3-4 Service Adjustment 3-4-1 White Balance - Calibration If picture color is wrong, do calibration first. Equipment : CA210, Patten : chess pattern Execute calibration in Factory Mode Source AV : PAL composite, Component : 1280*720/60Hz PC : 1024*768/60Hz ( chess patten ) 3-4-2 White Balance - Adjustment...
3 Alignments and Adjustments 3-4-3 Conditions for Measurement 1. On the basis of toshiba ABL pattern : High Light level (57 IRE) - INPUT SIGNAL GENERATOR : MSPG-925LTH * Mode 2 : 744X484@60 Hz 6 : 1280X720@60 Hz NO 21 : 1024X768@60 Hz * Pattern NO 36 : 16 Color Pattern NO 16 : Toshiba ABL Pattern 2.
Page 17
3 Alignments and Adjustments d) Adjust the high light. (Refer to table 1, 2 in adjustment position by mode) - Adjust red gain ('x') and blue gain ('y') to the color coordinates. * Do not adjust the green gain and sub-contrast (Y) data. Picture 4-3 Toshiba ABL Pattern High light Measurement point...
3 Alignments and Adjustments 3-5 Software Upgrade 3-5-1 How to Update Flash ROM 1. Install the Flash Downloader Connector Set(D-SUB) and D-SUB cable to execute Program Update. 2. Flash Downloader program update - Turn on the TV Set - Click "Connect" icon on the MSTAR tool. - Click "Read", and Choose a new S/W.
13 Circuit Descriptions 13 Circuit Descriptions 13-1 Block description Signal Power IP Board RF IN Scart S-Video Main Board Panel Component T-con Board HDMI Speaker IR/LED Bordeaux consists of three main blocks 1. Main board : Video signal processing 2. IP board : Power supply & Inverter 3.
Page 24
13 Circuit Descriptions 13-3 IP Board 13-3-1 19" IP Board Circuit Diagram Inverter Line Resonance SMPS Filter Switching Resonance Switching Output Rectifier Rectifier Part Part Transformer Part Rectifier Part DC/DC Signal SI-8008HFE 5.3V Resonance or AP1501A AC Input Controller (90Vac~264Vac) Controler Signal MC33067...
11 Disassembly and Reassembly 11 Disassembly and Reassembly This section of the service manual describes the disassembly and reassembly procedures for the TFT-LCD WARNING : This monitor contains electrostatically sensitive devices. Use caution when handling these components. 11-1 Disassembly Cautions : 1. Disconnect the monitor from the power source before disassembly. 2.
Page 27
11 Disassembly and Reassembly Description Picture Description 2. Lift up the rear cover and remove the stand. 3. Disonnect cable from the boards. 11-2...
Page 28
11 Disassembly and Reassembly Description Picture Description 4. Remove screws from the boards and lift up the boards. 11-3...
Page 29
11 Disassembly and Reassembly Description Description Picture 5. Remove screws and Lift up the Lcd panel. 11-4...
Page 30
11 Disassembly and Reassembly 11-2 Reassembly Reassembly procedures are in the reverse order of disassembly procedures. 11-5...
Page 31
11 Disassembly and Reassembly Memo 11-6...
6 Electrical Parts List 6 Electrical Parts List You can search for updated part codes through GSPN web site. URL : http://itself.sec.samsung.co.kr/ 6-1 LE19R86BDX Parts List Level Loc. No. Code No. Description & Specification Q'ty SA/SNA LE19R86BDX/BWT LE19R86BD,N11A/19R80-GBP,19,LCD-TV,RUSSI M0002 BN90-01199E ASSY COVER REAR;LE19R86BDX/XEC...
5 Exploded View & Parts List 5 Exploded View and Parts List - You can search for updated part codes through GSPN web site. URL : http://itself.sec.samsung.co.kr/ 5-1 LE19R86BDX Exploded View M0107 M0412 M0013 M0215 T0003 M0174 M0027 T0175...
Page 55
5 Exploded View & Parts List 5-2 LE19R86BDX Parts list Location Code.No Item & Specification Q'ty SA/SNA Remark T0003 BN96-05928D ASSY COVER P-FRONT;19R86,CIS,ABS+PMMA,HB S.N.A T0175 BN96-04760A ASSY SPEAKER P;16##,Bordeuax plus 19,Rig M0215 BN07-00330A LCD-PANEL;M190A1-L02,Haydn,6BIT FRC,427. M0412 BN96-05930A ASSY BRACKET P-PCB;-,19R8,-,SECC,-,-,IDT S.N.A M0107 BN63-03039A...
Page 56
10 Operating Instructions and Installation 10 Operating Instructions and Installation 10-1 Front - The product colour and shape may vary depending on the model. 1. SOURCE Toggles between all the available input sources (TV, Press to change channels. Ext., AV, S-Video, Component, PC, HDMI, DTV). In the on-screen menu, use the buttons In the on-screen menu, use this button as you use...
10 Operating Instructions and Installation 10-2 Connection Panel [Side Panel Jacks] Power Input The product colour and shape may vary depending on the model. - Whenever you connect an external device to your TV, make sure that power on the unit is turned off. - When connecting an external device, match the colour of the connection terminal to the cable.
Page 58
10 Operating Instructions and Installation Connecting HDMI - Supports connections between HDMI-connection-enabled AV devices (Set-Top Boxes, DVD players). - No additional Audio connection is needed for an HDMI to HDMI connection. ▶ What is HDMI? - "High Definition Multimedia interface" allows the transmission of high definition digital video data and multiple channels of digital audio ( 5.1 channels).
Page 59
10 Operating Instructions and Installation DIGITAL AUDIO OUT (OPTICAL) - Connect to a Digital Audio Component. EX-LINK - Service connection for qualified service engineer. 10. Connecting Component Devices (DTV/DVD) - Connect component video cables (optional) to component connector ("P ", "P ", "Y") on the rear of your set and the other ends to corresponding component video out connectors on the DTV or DVD.
10 Operating Instructions and Installation 10-3 Remote Control 1. Selects a target device to be controlled by the Samsung remote control (TV, DVD, STB, CABLE, VCR) 2. Television Standby button 3. Number buttons for direct channel access 4. One/Two-digit channel selection 5.
10 Operating Instructions and Installation 10-4 Installing VESA compliant mounting devices Mounting pad Button (sold separately) 1. Place the TV down on a soft cloth or cushion on a table. 2. Adjust the stand, pressing the button on the back of the stand. 3.
1 Precautions 1 Precautions Follow these safety, servicing and ESD precautions to prevent damage and to protect against potential hazards such as electrical shock. 1-1 Safety Precautions 1-1-1 Warnings For continued safety, do not attempt to modify the circuit board. Disconnect the AC power and DC Power Jack before servicing.
1 Precautions 1-2 Servicing Precautions WARNING: An electrolytic capacitor installed with the wrong polarity might explode. Caution: Before servicing units covered by this service manual, read and follow the Safety Precautions section of this manual. Note: If unforeseen circumstances create conflict between the following servicing precautions and any of the safety precautions, always follow the safety precautions.
1 Precautions 1-4 Installation Precautions 1. For safety reasons, more than two people are 6. Keep the antenna far away from any high-voltage required for carrying the product. cables and install it firmly. Contact with the high- voltage cable or the antenna falling over may 2.
2 Product Specifications 2 Product specifications 2-1 Fashion Feature Supreme Digital Interface & Networking -With a built-in HD digital tuner, it supports HD broadcasting with no particular set-top box and provides simple access with a single remote control. Excellent Picture Quality -DNIe technology provides life-like clear images.
14 Reference Infomation 14 Reference Infomation 14-1 Technical Terms - TFT-LCD - Auto Configuration(Auto adjustment) (Thin film Transistor Liquid Crystal Display) This is an algorithm to adjust monitor to optimum ADC(Analog to Digital Converter) condition by pushing one key. This is a circuit that converts from analog signal to digital signals.
Page 73
14 Reference Infomation - T.M.D.S - Interlace and Non-Interlace Methods (Transition minimized Differential Signaling) Showing the horizontal lines of the screen from the a kind of transmission method for Digital. top to the bottom in order is called the Non- It can be used from Video card to Main PBA.
Page 74
Enables high picture quality and clear sound channel to obtain the best viewing conditions. The throughout the country regardless of the location of Samsung LCD TV has both automatic and manual the viewer. channel fine-tuning features to enable the viewer to adjust their desired settings.
Page 76
14 Reference Infomation 14-2-2 Component 14-2-3 S-Video Separate RCA Green Pb (Cb) RCA Blue Pr (Cr) RCA Red Audio L 14-2-5 D-SUB RCA White Separate Audio R RCA Red Green Blue 14-2-4 A/V GND Red GND Green GND Blue RCA Yellow CVBS DDC Input power(+5V) Audio L...
Page 77
14 Reference Infomation 14-2-7 Scart 1 Signal Signal Audio output R Audio input R Video GND (RGB red) Audio output L Audio common GND RGB red input Video GND (RGB blue) Fast Blanking signal (RGB switching) Audio input L Video output GND RGB blue input Video input GND Switching voltage...
14 Reference Infomation 14-3 Timing Chart This section of the service manual describes the timing that the computer industry recognizes as standard for computer- generated video signals. 14-3-1 LCD Panel Mode1 mode Timing No. LTA400W2 Originator VESA Mode Name 1366/60Hz Resolution (H x V) 1366 x 768 HORIZONTAL...
14 Reference Infomation 14-3-2 Supported Modes (1) Timing No. Originator VESA VESA Mode Name VGA2 VGA3 640/72Hz 640/75Hz 640/67Hz Resolution (H x V) 720 x 400 640 x 480 720 x 400 720 x 400 640 x 480 HORIZONTAL Frequency 31.169kHz 31.469kHz 37.861kHz...
Page 80
14 Reference Infomation 14-3-3 Supported Modes (2) Timing No. Originator VESA VESA VESA Mode Name 800/60Hz 800/72Hz 800/75Hz Resolution (H x V) 800 x 600 800 x 600 800 x 600 HORIZONTAL Frequency 37.879kHz 48.077kHz 46.875kHz Total time 26.400 20.800 21.333 20.000 Active time...
Page 81
14 Reference Infomation 14-3-4 Supported Modes (3) Timing No. Originator VESA VESA VESA VESA Mode Name 1024/60Hz 1024/70Hz 1024/75Hz 1360/60Hz Resolution (H x V) 1024 x 768 1024 x 768 1024 x 768 1360 x 768 HORIZONTAL Frequency 48.363kHz 56.476kHz 60.023kHz 47.712kHz Total time...
4 Troubleshooting 4 Troubleshooting 4-1 First Checklist for Troubleshooting 1. Check the various cable connections first. - Check to see if there is a burnt or damaged cable. - Check to see if there is a disconnected cable connection or a connection is too loose. - Check to see if the cables are connected according to the connection diagram.
Page 99
4 Troubleshooting 4-2 Checkpoints by Error Mode 4-2-1 No Power LAMP off, power indicator Check a connection a power cable. LED red color? Does proper DC 13V appear Change a Assy PCB Power. at CN1001. Does proper DC A5V appear Check IC1020.
Page 100
R5043, R5042, R5040? cable. Change a main PCB ass'y. Does the digital data appear at the Check IC5002, 6003. output of RA6001~5? Change a main PBA. Check a LVDS cable? Please, Call to Samsung Co. LTD. Replace a lcd panel?
Page 101
4 Troubleshooting WAVEFORMS R,G,B Output Signal of IC5002, 6003...
Page 102
Check the IC5002. output of IC5002 (RA5008~13)? Change a main PBA. Does the digital data appear at Check the IC6003. output of IC6003? Change a main PBA. Check a LVDS cable? Please, Call to Samsung Co. LTD. Replace lcd panel?
Page 103
4 Troubleshooting Digital Output Data of IC5002, IC6003 Signal of HDMI(Data)
Page 104
Does the signal appear at #9 Change a main PCB ass'y. of TU6001? Does the digital data appear Check a IC500. at output of RA6001~6005? Change a main PCB ass'y. Check a LVDS cable? Please, Call to Samsung Co. LTD. Replacea lcd panel?
Page 106
Does the signal appear at Check a connection harness. #52 of IC5002? Does the digital data appear Check a IC6003. at output of RA6001~6005? Change a main PBA. Check a LVDS cable? Please, Call to Samsung Co. LTD. Replace lcd panel?
Page 107
4 Troubleshooting WAVEFORMS CVBS Output Signal 4-10...
Page 108
Does the Y/C signal appear Check a connection harness. at #50,51 of IC5002? Does the digital data appear Check IC6003. at output of RA6001~6005? Change a main PBA. Check a LVDS cable? Please, Call to Samsung Co. LTD. Replacea lcd panel? 4-11...
Page 109
4 Troubleshooting WAVEFORMS Digital Output Data of IC5002, 6003 Analog Signal(Y,C) to IC5002, 6003 4-12...
Page 110
4 Troubleshooting 4-2-7 No Sound Connect a sound cable. Picture is display, no sound. control a volume. Does the signal appear at Pin Check a connection harness. #1,2,3,11,12,15 of IC2001? Check IC2001. Check the DC 9V of IC2001? Change a main PBA. Does the signal appear at Pin #31,37,48,54 of Change a main PBA.
Page 111
4 Troubleshooting WAVEFORMS The Signal are Inputed to IC8005 DC +12V 4-14...
8 Wiring Diagrams 8-4 Power Board Layout Lamp Connector Power Connector Connecting to Inverter Connecting to - Upper / Main Board Left of panel backside Lamp Connector Connecting to Inverter AC Power Socket - Lower / Left of panel backside...
Page 116
8 Wiring Diagrams 8-5 IP Wiring Diagram CN101 PWM Dimming Control A13V A13V A13V ANA Dimming Control CFLL Drive Signal NAME CN201,202 COLD COLD NAME...