Table of Contents
Advertisement
Quick Links
Installation and Operation Manual for
PURE MINERALS™ MINERAL OXIDISER & SANITISER
MX15 | MX20 | MX25 | MX30 | MX35 | MX50
This equipment must be installed and serviced by a qualified technician. Improper installation can create electrical
hazards which could result in property damage, serious injury or death. Improper installation will void the
warranty.
This manual contains important information about the installation, operation and safe use of this product. Once
the product has been installed this manual must be given to the owner/operator of this equipment.
Advertisement
Table of Contents
Related Manuals for Evolution PURE MINERALS MX15
Summary of Contents for Evolution PURE MINERALS MX15
- Page 1 Installation and Operation Manual for PURE MINERALS™ MINERAL OXIDISER & SANITISER MX15 | MX20 | MX25 | MX30 | MX35 | MX50 This equipment must be installed and serviced by a qualified technician. Improper installation can create electrical hazards which could result in property damage, serious injury or death. Improper installation will void the warranty.
-
Page 2: Table Of Contents
TABLE OF CONTENTS 1.0 FOREWORD ....1 2.0 POOL CHEMISTRY....1 3.0 CELL INSTALLATION . -
Page 3: Foreword
Please read the instructions thoroughly before operating the unit. If you have any concerns or require further assistance, please do not hesitate to contact our friendly staff or any of our Evolution distributors. POOL CHEMISTRY It is important to note that the Mineral Oxidiser does not maintain the water chemistry of the swimming pool water;... -
Page 4: Cell Installation
POWER PACK CONTROLLER POWER OUTLET ® CELL HOUSING PROUDLY AUSTRALIAN MADE BY EVOLUTION BACKWASH LINE TO POOL RETURN FROM POOL/ SKIMMER Fig. 1... -
Page 5: Power Pack Installation
POWER PACK INSTALLATION The Mineral Oxidiser power pack is wall mounted using the supplied mounting bracket or directly hanging on the wall with screws (300mm centres). The power pack must be mounted at least 1 metre above the ground and 3 metres or more from the pool edge. It is strongly recommended that the power pack be installed where it is protected from the elements. -
Page 6: Operation
OPERATION The control interface on the power pack consists of the following: Fig. 3 1. Oxidiser Output LEDs If the correct salinity level is maintained in the water, all ten lights will illuminate at full output (100%). Each light represents a 10% incremental output. If all lights are not illuminated, then a higher salinity level will be required. - Page 7 Note: Turn off the Mineral Oxidiser at the power point before attempting to reset the circuit breaker. Should the circuit breaker continue to trip, then a local Evolution distributor should be contacted. 7. Switch This switch allows you to choose the timer operation mode for the Mineral Oxidiser and pool pump.
-
Page 8: Dosage
DOSAGE The Mineral Oxidiser is designed to work with all mineral blend products to sanitise your pool effectively, but works best as a complete system with high-quality Pure Minerals™ Magnesium Crystals. Using Pure Minerals™ in conjunction with pool salt will produce a magnesium-rich and precisely sanitised pool with minimal maintenance. - Page 9 Table 1: Pure Minerals™ Start-Up and Activate Dosage Current Add (kg) 10,000L 20,000L 30,000L 40,000L 50,000L Salinity (ppm) Pure Minerals Pool Salt Pure Minerals Pool Salt Pure Minerals 1,000 Pool Salt Pure Minerals 1,500 Pool Salt Pure Minerals 2,000 Pool Salt Pure Minerals 2,500 Pool Salt...
- Page 10 Table 2: Pure Minerals™ Maintenance Dosage Current Add (kg) 10,000L 20,000L 30,000L 40,000L 50,000L Salinity (ppm) Pure Minerals 2,000 Pool Salt Pure Minerals 2,500 Pool Salt Pure Minerals 3,000 Pool Salt Pure Minerals 3,500 Pool Salt Pure Minerals 4,000 Pool Salt Current Add (kg) 60,000L...
-
Page 11: Maintenance
Only qualified electrical technicians should service the power pack. For the nearest Evolution recommended service technician, please contact Evolution Water & Lighting Solutions on 07 5565 0000 or email us at service@evolutionwls.com.au. -
Page 12: Troubleshooting
TROUBLESHOOTING Fault/Problem Possible Cause Remedy Pump turned off. Ensure the pump is on. Closed valve. Open valve. Air in the system. Check all o-rings and grease. NO FLOW All oxidiser output Dirty filter. Clean or backwash filter. LEDs flashing Low water level. Fill up the pool. -
Page 13: Warranty
10.0 10.1 Evolution Mineral Oxidisers are covered by a 3-year full warranty from the date of purchase. The power pack and electrolytic cell are covered against defects in materials and assembly from the date of purchase in a domestic application. All electrical or mechanical failure due to faulty components will be repaired or replaced at no cost to the owner, including labour. -
Page 14: Notes
NOTES 11.0... - Page 16 1/33 Hinkler Drive, Highland Park QLD 4211, Australia +61 7 5565 0000 Unless otherwise indicated, copyright in the content of this document is the property of Evolution Water and Lighting Solutions under Australian copyright law. Unless otherwise indicated, content may not be reproduced or transmitted without our prior written permission.
Need help?
Do you have a question about the PURE MINERALS MX15 and is the answer not in the manual?
Questions and answers