Advertisement
Quick Links
Advertisement
Related Manuals for NB Security Tronix ST-IP4FTD
Summary of Contents for NB Security Tronix ST-IP4FTD
- Page 1 ST-IP4FTD QUICK START GUIDE www.nacebrands.com www.securitytronix.com...
- Page 2 ST-IP4FTD QUICK START GUIDE Thank you for purchasing our product. If there are any questions, or requests, please do not hesitate to contact the dealer. About This Document This manual may contain several technical incorrect places or printing errors, and the content is subject to change without notice. The updates will be added to the new version of this manual.
- Page 3 ST-IP4FTD QUICK START GUIDE Regulatory Information FCC Information FCC compliance: This equipment has been tested and found to comply with the limits for a digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
- Page 4 ST-IP4FTD QUICK START GUIDE 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points.
- Page 5 ST-IP4FTD QUICK START GUIDE Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into “Warnings” and “Cautions” Warnings: Serious injury or death may occur if any of the warnings are neglected.
- Page 6 ST-IP4FTD QUICK START GUIDE ● Do not connect several devices to one power adapter as adapter overload may cause over-heating or a fire hazard. ● Please make sure that the plug is firmly connected to the power socket. When the product is mounted on wall or ceiling, the device shall be firmly fixed.
- Page 7 ST-IP4FTD QUICK START GUIDE ● Do not place the camera in extremely hot, cold (the operating temperature shall be-22F~+140F,or -40°F ~ 140°F if the camera model has an “H” in its suffix), dusty or damp locations, and do not expose it to high electromagnetic radiation. ●...
- Page 8 ST-IP4FTD QUICK START GUIDE Table of Contents 1 Appearance Description ..............8 2 Installation ..................10 3 Setting the Network Camera over the LAN ........16 4 Accessing via Web Browser ............21...
-
Page 9: Appearance Description
ST-IP4FTD QUICK START GUIDE 1 Appearance Description Figure 1-1 Overview Table 1-1 Description Description 10M/100M self-adaptive Ethernet interface Power Cable Trim Ring... - Page 10 ST-IP4FTD QUICK START GUIDE Description Lens IR LED Enclosure Dome Drive Please make sure that the power adapter is compatible with the camera. This series of camera supports Power over Ethernet (PoE), and the standard power supply is 12 VDC.
-
Page 11: Installation
ST-IP4FTD QUICK START GUIDE 2 Installation Before you start: Make sure the device in the package is in good condition and all the assembly parts are included. Make sure all the related equipment is powered-off during installation. Check the product specification for details regarding optimum installation environment. - Page 12 ST-IP4FTD QUICK START GUIDE ● Make sure that there is no reflective surface too close to the camera lens. The IR light from the camera may reflect back into the lens causing poor image quality. ● The foam ring around the lens must be seated flush against the inner surface of the bubble to isolate the lens from the IR LEDS.
- Page 13 ST-IP4FTD QUICK START GUIDE Drill the screw holes and the cable hole on the ceiling according to the drill template. Figure 2-2 The Drill Template There are two cable outlet methods. One is to route the cables through the cable hole, and the other is to route the cables through the side outlet shown below.
- Page 14 ST-IP4FTD QUICK START GUIDE Three side outlets on the enclosure are selectable, which makes routing the cables easier instead of drilling a cable hole on the ceiling. Use a plier to remove the plastic tab and route the cables through the hole. Connect the corresponding power/network cable.
- Page 15 ST-IP4FTD QUICK START GUIDE 3). Tighten the lock screw to fix the optimum surveillance angle. Lock Screw Figure 2-5 Lock Screw Figure 2-6 Adjust the Lens...
- Page 16 ST-IP4FTD QUICK START GUIDE Attach the trim ring to the camera and rotate the trim ring clockwise to get it secured. Figure 2-7 Install the Trim Ring Figure 2-8 Complete the Installation...
-
Page 17: Setting The Network Camera Over The Lan
ST-IP4FTD QUICK START GUIDE 3 Setting the Network Camera over the Purpose: To view and configure the camera via LAN (Local Area Network), you need to connect the network camera in the same subnet with your PC. Then, install the SADP or client software to search and change the IP of the network camera. - Page 18 ST-IP4FTD QUICK START GUIDE Use client software and to list the online devices. Please refer to the user manual of client software for detailed information. 2. Change the IP address and subnet mask to the same subnet of your PC. Refer to the following introductions to set IP address with SADP software: ...
- Page 19 ST-IP4FTD QUICK START GUIDE Figure 3-2 Search Online Devices Devices can be searched and displayed in the list 15 seconds after it goes online; it will be removed from the list 45 seconds after it goes offline. Search online devices manually: You can also click to refresh the online device list manually.
- Page 20 ST-IP4FTD QUICK START GUIDE displayed in the Modify Network Parameters panel on the right side as shown in Figure 3-4. Edit the modifiable network parameters, e.g. IP address and port number. Enter the password of the admin account of the device in the Password field and click Save to save the changes.
- Page 21 ST-IP4FTD QUICK START GUIDE Figure 3-4 Modify Network Parameters 3. Enter the IP address of the network camera in the address field of the web browser to view the live video. The default IP address is “192.0.0.64”. The default user name is “admin”, and password is “12345”.
-
Page 22: Accessing Via Web Browser
ST-IP4FTD QUICK START GUIDE 4 Accessing via Web Browser System Requirement: Operating System: Microsoft Windows XP SP1 and above version / Vista / Win7 / Server 2003 / Server 2008 32bits CPU: Intel Pentium IV 3.0 GHz or higher RAM: 1G or higher Display: 1024×768 resolution or higher Web Browser: Internet Explorer 6.0 and above version, Apple Safari 5.02 and above version, Mozilla Firefox 3.5 and above version and... - Page 23 ST-IP4FTD QUICK START GUIDE Figure 4-1 Login Interface 5. Install the plug-in before viewing the live video and managing the camera. Please follow the installation prompts to install the plug-in. You may have to close the web browser to finish the installation of the plug-in.
- Page 24 ST-IP4FTD QUICK START GUIDE Figure 4-2 Download Plug-in Figure 4-3 Install Plug-in (1)
- Page 25 ST-IP4FTD QUICK START GUIDE Figure 4-4 Install Plug-in (2) 6. Reopen the web browser after the installation of the plug-in and repeat steps 2-4 to login. For detailed instructions of further configuration, please refer to the user manual of the network camera. If there are any questions, or requests, please contact our support department at 1-800-688-9282.
- Page 26 SECURITYTRONIX 2-Year Limited Fixed Camera Warranty Securitytronix. (the "Company") warrants to the Original Purchaser that the Fixed Camera is free from defects in workmanship or material under normal use. This warranty starts on the date of shipment of the hardware to the Original Purchaser. During the warranty period, the Company agrees to repair or replace, at its sole option, without charge to Original Purchaser, any defective component in the Fixed Camera.