Related Manuals for µ-Dimension COMPETITION ProZ2-50
Summary of Contents for µ-Dimension COMPETITION ProZ2-50
- Page 1 ProZ2-50 ProZ4-50 ProZ2-150 ProZ4-80 ProZ2-200 ProZ4-110 ProZ2-300 ProZ4-150 ProZ1-1000AB ProZ4-75 24Volt ProZ1-1500AB ProZ2-300 24Volt...
- Page 2 INTRODUCTION Amplifiers provide high-performance sound reinforcement for your mobile audio equipment. Its versatility enables compatibility with optional Equalizers, Frequency Dividing Network Crossovers, and other audio processors in a customized system. The Multi-Mode bridging capabilities allow flexibility in hosting several different speaker configurations.
-
Page 3: Planning Your System
PLANNING YOUR SYSTEM Before beginning the installation, consider the following: a. If you plan to expand your system by adding other components sometime in the future, ensure adequate space is left, and cooling requirements are met. Should you use high or low level inputs? Your Amplifier has been designed to accept either High-Level ( speaker outputs from your radio ) or Low-Level ( Pre-Amp outputs from your radio ) signal source. -
Page 4: Mounting Surface
MOUNTING SURFACE Cooling requirements are considerably relaxed when mounting inside the passenger compartment since the driver will not often allow temperatures to reach a critical point. Floor mounting under the seat is usually satisfactory as long as there is at least 1 inch (2cm) above the Amplifier’s fins for ventilation. -
Page 5: Connecting The Power
CONNECTING THE POWER CAUTION AS A PRECAUTION, IT IS ADVISABLE TO DISCONNECT THE VEHICLE’S BATTERY BEFORE MAKING CONNECTION TO THE + 12 VOLT SUPPLY WIRING. 10 GAUGE (Thicker if planning for additional Amplifiers) wire is recommended for both the power and ground wires. 20 Gauge, for the remote turn-on wire. Both types available at most Mobile Audio Dealers or Installation Shops. -
Page 6: Connecting The Speakers
CONNECTING THE SPEAKERS 1. 2CH Amplifier a. 1 Subwoofer BRIDGE R CH L CH b. Mono Mode BRIDGE Subwoofer - 5 -... - Page 7 CONNECTING THE SPEAKERS 1. 4CH Amplifier a. 4CH Mode b. 3CH Mode c. 2CH Mode...
-
Page 8: Features And Controls
FEATURES AND CONTROLS 4 Channel 2 Channel BRIDGE... - Page 9 FEATURES AND CONTROLS RCA Low Level Input Jacks lt allows left and right inputs to be connected to the amplifier using RCA plugs. RCA Line Output Jacks Full range output from channel L&R inputs is provided at Line Out Jacks. Input Level Control It allows for the adjustment of the gain of both channels to match the output level of the source.
- Page 10 CONNECTING THE SPEAKERS +12V +12V FEATURES AND CONTROLS LINE INPUT LINKABLE POWER LEVEL SUB-SONIC BASS BOOST PHASE SHIFT MASTER PROT. SLAVE 0.2V 15Hz 45Hz 50Hz 250Hz 12dB MASTER REMOTE BASS SLAVE CONTROL +12V +12V...
- Page 11 FEATURES AND CONTROLS RCA Low Level Input Jacks lt allows left and right inputs to be connected to the amplifier using RCA plugs. RCA Line Output Jacks Full range output from channel L&R inputs is provided at Line Out Jacks. Input Level Control It allows for the adjustment of the gain of both channels to match the output level of the source.
-
Page 12: Troubleshooting
TROUBLESHOOTING Before removing your Amplifier, refer to list below and follow suggested procedure. Speakers and their wires should be tested first. No Output: a. Confirm that all terminal strip connections are firmly connected. b. Check in-line and built-in fuses. Both “+12V” and “RMT” terminals must have +12 Volts to chassis ground. - Page 13 SPECIFICATIONS MODEL ProZ2-50 ProZ2-150 ProZ2-200 ProZ2-300 SPEC. POWER OUTPUT DC(11V) RMS AT 4 Ohm , STEREO 50W X 2CH 150W X 2CH 200W X 2CH 300W X 2CH RMS AT 2 Ohm , STEREO 80W X 2CH 200W X 2CH 300W X 2CH 450W X 2CH RMS AT 1 Ohm , STEREO...
- Page 14 manufactured for Europe A Division of CHPW Friedrich-Ebert-Str. 42 D-92637 Weiden / Germany...