Lectronics DM Series Hardware And Software Installation Manual

Digital audio processors

Advertisement

Quick Links

DM Series
Digital Audio Processors
Models:
DM1624
DM1612
DM812
Fill in for your records:
Serial Number:
Purchase Date:
HARDWARE and SOFTWARE INSTALLATION GUIDE
Rio Rancho, NM, USA
www.lectrosonics.com

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the DM Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Lectronics DM Series

  • Page 1 HARDWARE and SOFTWARE INSTALLATION GUIDE DM Series Digital Audio Processors Models: DM1624 DM1612 DM812 Fill in for your records: Serial Number: Purchase Date: Rio Rancho, NM, USA www.lectrosonics.com...
  • Page 2 DM Series Installation Guide Important Safety Instructions This symbol, wherever it appears, alerts you to the presence of uninsulated dangerous voltage inside the enclosure -- voltage that may be sufficient to constitute a risk of shock. This symbol, wherever it appears, alerts you to important operating and maintenance instructions in the accompanying literature.
  • Page 3: Table Of Contents

    DM Series Installation Guide Table of Contents INTRODUCTION .............................. 5 Unpacking the Unit .................................5 Items Included in the Box: ..............................5 HARDWARE INSTALLATION .......................... 6 Installing the DM System into a Rack ..........................6 Cables ...................................6 Audio Connections ................................6 Audio Connection Guidelines ............................6 Audio Inputs ...................................6...
  • Page 4 DM Series Installation Guide LECTROSONICS, INC.
  • Page 5: Introduction

    Power cable To get the most out of the DM system, it is suggested 5-pin de-pluggable connectors: to review the information presented in the DM Series 20 each for the DM1624 Reference Manual. 14 each for the DM1612...
  • Page 6: Hardware Installation

    Note the labeling on the DM Chassis for the positive and negative leads. Ground is shared between two connections (the center pin). For balanced connec- tions, all three leads can be connected. NOTE: The DM Series does not have a “pin 1 problem.” LECTROSONICS, INC.
  • Page 7: Phantom Power

    DM Series Installation Guide Source DM In Examples: Microphone Number 1; Shield From Specification Sheet: (min) = 11 V (typical) = 4 mA = 15 V - (1k)(.004A) Balanced source to DM input = 15 V - 4V = 11 V...
  • Page 8: Programmable Inputs

    DM Series Installation Guide DM Out Destination Shield DM Out to Unbalanced Input (3-Wire) Programmable Inputs and DM Out Destination Outputs (DM1624 shown) In Control or Analog Out Control on the Program- Shield mable Inputs control tab in the Control Panel GUI.
  • Page 9: Programmable Inputs And Outputs Wiring Diagram Example

    DM Series Installation Guide Expansion I/O ports Both LEDs and 5V relay coils can be powered by the +5 V DC pins on the programmable input connector, as The four RJ45 connectors on the rear panel are used long as the maximum combined current for all LEDS to interconnect LecNet2™...
  • Page 10: Expansion Port Digital Audio Network Interface Interconnection Diagram

    DM Series Installation Guide Expansion Port Digital Audio Network Interface DM1624 Location of Communication Ports Interconnection Diagram 1 - GND 6 - IN 20 11- OUT 13 16 - IN 15 21 - OUT 10 1 - GND 6 - IN 20...
  • Page 11: Installing Lecnet2™ Software And Usb Driver

    Windows Found New Hardware LecNet2™ includes the necessary Control Panels to Wizard automatically opens. Use the following pro- configure and monitor all the DM series products plus cedure to install the LecNet2™ USB driver using the the Venue Modular Receiver system.
  • Page 12: Installation Additional Units (Or Lecnet 2 ™ Devices)

    DM Series Installation Guide 2. Windows discovers the previously installed USB driver. It is likely that a dialog will open warning you that the driver has not passed Windows Logo Test- ing. Click Continue Anyway. 5. When the driver installation is complete, the final page of the Wizard appears.
  • Page 13: Usb Driver Installation (Windows 2000)

    DM Series Installation Guide USB Driver Installation (Windows 2000) First Time Installation 4. When it is found, the LecNet2™ device name will be displayed. Click Next> to install the driver. When a LecNet2™ device is connected to a comptuer system running the Windows 2000 operating system ®...
  • Page 14: Initial Setup

    DM Series Installation Guide Initial Setup Connect Menu The initial setup of a DM system is a relatively simple three step process: connect the unit to the computer, turn on the computer and select the appropriate control panel, preset the input, matrix and output. This process assumes that LecNet2™...
  • Page 15: Initial Setup Hints

    DM Series Installation Guide Inputs Matrix Outputs 6) Help is always available by clicking Help on the Main Menu Bar. This Help is a comprehensive resource and includes the latest revisions to the software and firmware. IMPORTANT: ANY CHANGES MADE DURING SETUP MUST BE SAVED IN THE UNIT VIA THE PRESET MENU.
  • Page 16: Limited One Year Warranty

    LIMITED ONE YEAR WARRANTY The equipment is warranted for one year from date of purchase against defects in materials or workmanship provided it was purchased from an authorized dealer. This warranty does not cover equipment which has been abused or damaged by careless handling or shipping.

This manual is also suitable for:

Dm1624Dm1612Dm812

Table of Contents