Gigabyte MZ31-AR0 Quick Reference Manual

43 44 1 2 3 4 5 6
42
34
35 36 37 38 39 40 41
33
32
31 12
13
30
29
17
18
28
27
26
CPU
25
24 22
23 21
20
ATX Power/ 电源
8 4
No. Pin Define
No. Pin Define
1
13 3.3V
1 3.3V
14 -12V
2 3.3V
15 GND 5 1
3 GND
4 +5V 16 PS_ON No. Pin Define
17 GND
5 GND 1 GND
18 GND 2 GND
6 +5V
19 GND
7 GND 3 GND
20 -5V
8 Power Good 4 GND
21 +5V 5 +12V
9 5VSB
12 24 22 +5V
10 +12V 6 +12V
23 +5V 7 +12V
11 +12V
12 3.3V 24 GND 8 +12V
COM2 Connector
1 2
No. Pin Define No. Pin Define 10 9
1 NDCD- 6 NDSR-
2 NSIN 7 NRTS-
3 NSOUT 8 NCTS-
4 NDTR- 9 NRI-
2 1
5 GND 10 No Pin
9 10
TPM Connector/
可信平台模块
2 14
1 13
20
No. Pin Define No. Pin Define
1 Clock 8 No Connect
2 P_3V3_AUX 9 LPC_LAD2
3 LPC_RST 10 No Pin
4 P3V3 11 LPC_LAD3
11
5 LPC_LAD0 12 GND
6 IRQ_SERIAL 13 LPC_FRAME_N
7 LPC_LAD1 14 GND
Jumper Settings/ 跳线设置
1
No.
1
2
2
3
3
4
5
5 4
PN:25ME0-MZ3101-Q0H
MZ31-AR0 Quick Reference Guide/ 快速测试参考指南
No. Code
7
1 SW_ID
2 R_USB1
3 USB3_LAN
4 LED_LAN1
5 SFP+_1/SFP+_2 SFP+ LAN port #1/SFP+ LAN port#2
8
6 LED_LAN2
7 COM1_VGA
8 SYS_FAN3
9
9 PMBUS_SEL
10 S3_MASK
11 PMBUS
10
14
12 LED_BMC1
11
13 TPM_LPC
14 P2
15 P4
15
16 P3
17 CPU1_FAN
16
18 CPU0_FAN
19 BIOS_PWD
20 BIOS_RCVR
21 SLSAS_0
22 SLSAS_1
23 SLSAS_2
24 SLSAS_3
25 FP_1
26 BP_1
27 M2_SK1
28 F_USB1
29 SYS_FAN1
30 F_USB2
31 SYS_FAN4
32 SYS_FAN5
33 SYS_FAN2
19
CPU/System FAN/ 风扇
1 4
No. Pin Define
1 GND
2 +12V
3 Sense
4 1
4 Speed Control
PMBUS
No.
1
2
No. Pin Define
5
3
1 PMBus Clock
4
2 PMBus Data
5
3 PMBus Alert
6
4 GND
1 7
5 3.3V Sense
8
9
USB 2.0 Header
10
No. Pin Define No. Pin Define
1 Power (5V) 6 USB DY+
2 Power (5V) 7 GND
3 USB DX- 8 GND
4 USB DY- 9 No Pin
5 USB DX+ 10 No Connect
USB 3.0 Header
No. Pin Define No. Pin Define
1 Power 11 IntA_P2_D+
1
2 IntA_P1_SSRX- 12 IntA_P2_D-
3 IntA_P1_SSRX+ 13 GND
4 GND 14 IntA_P2_SSTX+
5 IntA_P1_SSTX- 15 IntA_P2_SSTX-
6 IntA_P1_SSTX+ 16 GND
7 GND 17 IntA_P2_SSRX+
10
8 IntA_P1_D- 18 IntA_P2_SSRX-
9 IntA_P1_D+ 19 Power
10 NC 20 No Pin
Desription
Clear CMOS Jumper
1-2 Closed: Normal operation (Default setting)
2-3 Closed: Clear CMOS data.
PMBus Address Selection Jumper
1-2 Closed: From core chipset.
2-3 Closed: From BMC. (Default setting)
S3 Power On Select Jumper
1-2 Close: Stop an initial power on when BMC is not ready.
2-3 Close: Keep initial power on. (Default setting)
Clearing Supervisor Password Jumper
3
1-2 Close: Normal operation. (Default setting)
2-3 Close: Skip supervisor password.
BIOS Recovery Jumper
BMC Firmware Readiness LED
1-2 Close: Normal operation. (Default setting)
2-3 Close: BIOS recovery mode.
Description
ID button with LED
USB 2.0 ports
Server managemnt LAN port (top)/USB 3.0 port (bottom)
SFP+ LAN port #1 active/link LEDs
SFP+ LAN port #2 active/link LEDs
Serial port (top) / VGA port (bottom)
System fan connector #3
PMBus select jumper
S3 power on select jumper
PMBus connector
BMC firmware readiness LED
TPM connector
2 x 12 pin main power connector
2 x 4 pin power connector (for memory)
2 x 4 pin power connector (for CPU)
CPU fan connector #1
CPU fan connector #0
Clearing Supervisor Password jumper
BIOS recovery jumper
Slimline connector #0 (SATA 6Gb/s signal)
Slimline connector #1 (SATA 6Gb/s signal)
Slimline connector #2 (SATA 6Gb/s signal)
Slimline connector #3 (SATA 6Gb/s signal)
Front panel header
HDD back plane board header
M.2 slot (Gen3/x4)
USB 3.0 header
System fan connector #1
USB 2.0 header
System fan connector #4
System fan connector #5
System fan connector #2
1 7
9
3 6
4 5
8
2
Desription
Serial port
VGA port
SFP+ LAN port #2 active/link LEDs
SFP+ LAN port #2
SFP+ LAN port #1
SFP+ LAN port #1 active/link LEDs
10/100/1000 Server Management LAN port
USB 3.0 ports
USB 2.0 ports
ID button with LED
External cap
1
3
2
4
1
2
3
5
RDIMM Maximum Frequency Supported Table
DIMMs
Populated
1
2
IPMB
No. Pin Define
1 Clock
1
DDR Population Table
2 GND
3 Data
DIMMs
Populated
1
2
State Description
On BMC firmware is initial
Blink BMC firmware is ready
Off AC loss
No. Code Description
34 COM2 Serial port cable connector
35 PCIE_1 PCIe x16 slot (Gen3/x16)
36 PCIE_2 PCIe x8 slot (Gen3/x8)
37 PCIE_3 PCIe x16 slot (Gen3/x16)
38 PCIE_4 PCIe x16 slot (Gen3/x16)
39 PCIE_5 PCIe x16 slot (Gen3/x8)
40 PCIE_6 PCIe x16 slot (Gen3/x16)
41 PCIE_7 PCIe x8 slot (Gen3/x8)
42 BAT Battery socket
43 IPMB IPMB connector
44 CLR_CMOS Clear CMOS jumper
Rear I/O Connector/ 后面板接口
Green/Yellow Link LED
Green Active LED
10
SFP+ LAN Link and Speed LED:
State
Description
Yellow On 1 Gbps data rate
Green On 10 Gbps data rate
SFP+ LAN Active LED:
State Description
Green On Link between system and network or no access.
Green Blink Data transmission or receiving.
Off No data transmission or receiving.
Installing CPU/Heatsink
4
7
2
2
6
3
1
Memory Population Configuration/ 安装内存
LRDIMM Maximum Frequency Supported Table
DIMM Frequency (MT/s)
DIMMs
2R Populated
2DR
1R 4DR 1.2V
2S2R
2S4R
1
-- --
1 2666
-- --
1 2400
-- --
1 Not Supported
2 -- --
2133
2
-- 2133
1 1
-- -- 2133
2
-- --
2 Not Supported
1 -- 1
Not Supported
-- 1 1 Not Supported
NOTE!
 1R: 1 package rank of SDP DRAMs
 2R: 2 package rank of SDP DRAMs
DIMM0 DIMM1
 2DR: 2 package rank of DDP DRAMs
 4DR: 4 package rank of DDP DRAMs
-- 1
 1S2R/1S4R/1S8R: 1 package rank of 2/4/8 high 3DS DRAMs
1 1  2S2R/2S4R/2S8R: 2 package rank of 2/4/8 high 3DS DRAMs
 DIMM must be populated in sequential alphabetic order, starting with bank A.
 When only one DIMM is used, it must be populated in memory slot A1.
Front Panel Header / 前面板
No. Pin Define No. Pin Define
1 2 1 Power LED+ 2 5V Standby
4 ID LED+
3 No Pin
6 ID LED-
5 Power LED-
8 System Status LED+
7 HDD LED+
10 System Status LED-
9 HDD LED-
12 LAN1 Active LED+
11 Power Button
14 LAN1 Link LED-
13 GND
16 SMBus Data
15 Reset Button
18 SMBus Clock
17 GND
23 24
20 Case Open
19 ID Button
22 LAN2 Active LED+
21 GND
24 LAN2 Link LED-
23 NMI Switch
HDD Back Plane Board Header/ 硬盤背板排針
No. Pin Define No. Pin Define
1 HP_ALERT 2 BPMI_DIN/OUT
1 2
4 BPMI_DIN/IN
3 GND
6 GND
5 BPMI_LOAD
8 PLD_Program_ENABLE
7 BPMI_CLK
10 GLED_GRN_N
9 GLED_AMB_N
11 FAN_IRQ_N 12 No Connect
14 GND
13 BP_SCL
16 BP_RST_N
15 BP_SDA
18 GND
17 SMB_U2_TMP_SCL
20 I2C_DEV_RST
19 SMB_U2_TMP_SDA
22 GND
21 PH_HP_SCL0
24 GND
23 PH_HP_SDA0
29 30
26 GND
25 No Connect
27 No Connect 28 GND
30 P_3V3_AUX
29 P_3V3_AUX
Speed LED Link/Activity
LED
10/100/1000 LAN LED:
State Description
Yellow On 1Gbps data rate
Green On 100Mbps data rate
Off 10Mbps data rate
ID button/LED:
State Description
Blue On System identifcation is active.
System identifcation is disabled.
Off
NOTE!
1
 When installing the heatsink to CPU,
9
use T20-Lobe driver to tighten 4 captive nuts
3
in sequence as 1-4.
 The screw tightening torque:
8
16.1 ± 1.2 kgf-cm (14.0± 1.0 lbf-in)
DIMM Frequency (MT/s)
1.2V
1R 2S4R 4DR
-- -- Not Supported
1
2666
-- 1 --
-- --
1 2666
2 -- -- Not Supported
1 Not Supported
1 --
-- 2133
2 --
-- -- 2
2133
-- Not Supported
1 1
-- 2133
1 1