Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for SKILTEC LUXAFLEX LUMINETTE
Summary of Contents for SKILTEC LUXAFLEX LUMINETTE
- Page 1 PRODUCT INFORMATION MANUAL SECTION: 12B LUMINETTE PRIVACY SHEERS POWERVIEW MOTORISATION LUMINETTE PRIVACY SHEERS POWERVIEW MOTORISATION ISSUE DATE: FEBRUARY 2018 ORIGINATOR: SKILTEC REPLACES ISSUE DATE: FEB 2018 APPROVED BY: S. GONZALEZ PAGE 1 OF 29...
-
Page 2: Installation
PRODUCT INFORMATION MANUAL SECTION: 12B LUMINETTE PRIVACY SHEERS POWERVIEW MOTORISATION LUMINETTE PRIVACY SHEERS ® PowerView Motorisation ™ Installation Operation Care • • ISSUE DATE: FEBRUARY 2018 ORIGINATOR: SKILTEC REPLACES ISSUE DATE: FEB 2018 APPROVED BY: S. GONZALEZ PAGE 2 OF 29... -
Page 3: Product View
Control Button Modular Motor Assembly Treatment DC Power PowerView ™ Supply Remote DC Power C-Clip Supply Cable Left Stack Right Stack ISSUE DATE: FEBRUARY 2018 ORIGINATOR: SKILTEC REPLACES ISSUE DATE: FEB 2018 APPROVED BY: S. GONZALEZ PAGE 3 OF 29... -
Page 4: Tools And Fasteners Needed
Rotate the supports in either direction until they can be pulled off. Remove Foam Supports IMPORTANT: With wider fabrics, the SofTrak headrail may be shipped separately. ISSUE DATE: FEBRUARY 2018 ORIGINATOR: SKILTEC REPLACES ISSUE DATE: FEB 2018 APPROVED BY: S. GONZALEZ PAGE 4 OF 29... -
Page 5: Mounting Types And Window Terminology
Refer to the appropriate page below based on your order: ■ Reveal/Ceiling Fit — Page 4 ➤ Face Fit — Page 7 ➤ ISSUE DATE: FEBRUARY 2018 ORIGINATOR: SKILTEC REPLACES ISSUE DATE: FEB 2018 APPROVED BY: S. GONZALEZ PAGE 5 OF 29... - Page 6 When attaching brackets into drywall, additional brackets may be required to keep the headrail level after the fabric is attached. ISSUE DATE: FEBRUARY 2018 ORIGINATOR: SKILTEC REPLACES ISSUE DATE: FEB 2018 APPROVED BY: S. GONZALEZ PAGE 6 OF 29...
- Page 7 160mm. See the illustration below. Reveal Fit Fully Recessed Mounting Depth 160mm Minimum Fully Recessed Depth Bracket Headrail Stacked Fabric Window Side Vane ISSUE DATE: FEBRUARY 2018 ORIGINATOR: SKILTEC REPLACES ISSUE DATE: FEB 2018 APPROVED BY: S. GONZALEZ PAGE 7 OF 29...
-
Page 8: Mount The Brackets
Loosen screws to add or remove shims. Proceed to “Install the SofTrak Headrail” on page 23. ™ ISSUE DATE: FEBRUARY 2018 ORIGINATOR: SKILTEC REPLACES ISSUE DATE: FEB 2018 APPROVED BY: S. GONZALEZ PAGE 8 OF 29... - Page 9 Each two-hole section is 13mm length. Extension Bracket ISSUE DATE: FEBRUARY 2018 ORIGINATOR: SKILTEC REPLACES ISSUE DATE: FEB 2018 APPROVED BY: S. GONZALEZ PAGE 9 OF 29...
- Page 10 Be sure to clear all floor obstructions such as carpet, vents, rugs, etc. Floor Surface ISSUE DATE: FEBRUARY 2018 ORIGINATOR: SKILTEC REPLACES ISSUE DATE: FEB 2018 APPROVED BY: S. GONZALEZ PAGE 10 OF 29...
- Page 11 IMPORTANT: With spacer blocks, place the screws in the middle of the slots to make aligning the brackets easier. Bushings Inserted ISSUE DATE: FEBRUARY 2018 ORIGINATOR: SKILTEC REPLACES ISSUE DATE: FEB 2018 APPROVED BY: S. GONZALEZ PAGE 11 OF 29...
- Page 12 IMPORTANT: A maximum of four spacer blocks can be used. Hook the top of the faceplate to the front spacer block and snap ■ it into place. Faceplate ISSUE DATE: FEBRUARY 2018 ORIGINATOR: SKILTEC REPLACES ISSUE DATE: FEB 2018 APPROVED BY: S. GONZALEZ PAGE 12 OF 29...
-
Page 13: Bracket Locations - Corner And Bay Windows
For bay windows, treat the center sheer as a corner system on both ends of ■ the headrail. Motor Brackets 200mm 130mm 75mm ISSUE DATE: FEBRUARY 2018 ORIGINATOR: SKILTEC REPLACES ISSUE DATE: FEB 2018 APPROVED BY: S. GONZALEZ PAGE 13 OF 29... -
Page 14: Install The Softrak ™ Headrail
Right Stack Design — Minimum Clearances Non-Motor End Motor End Left Stack Design — Minimum Clearances 22mm Motor End Non-Motor End ISSUE DATE: FEBRUARY 2018 ORIGINATOR: SKILTEC REPLACES ISSUE DATE: FEB 2018 APPROVED BY: S. GONZALEZ PAGE 14 OF 29... -
Page 15: Side-By-Side (Abutted) Installations (Simulated Split Stack)
Swivel Swivel Swivel Plates RTW Not Recommended Proper Installation Simulated Split Stack Swivel Plates ISSUE DATE: FEBRUARY 2018 ORIGINATOR: SKILTEC REPLACES ISSUE DATE: FEB 2018 APPROVED BY: S. GONZALEZ PAGE 15 OF 29... - Page 16 If necessary, use a screwdriver to turn the tilt gear until it is aligned. ➤ Aligned Tilt Gear ISSUE DATE: FEBRUARY 2018 ORIGINATOR: SKILTEC REPLACES ISSUE DATE: FEB 2018 APPROVED BY: S. GONZALEZ PAGE 16 OF 29...
-
Page 17: Connect The Dc Power Supply
The next button press will traverse the carriers or rotate the pinion clips in the opposite direction. ISSUE DATE: FEBRUARY 2018 ORIGINATOR: SKILTEC REPLACES ISSUE DATE: FEB 2018 APPROVED BY: S. GONZALEZ PAGE 17 OF 29... - Page 18 Unroll the fabric as you clip the rest of the vanes into the pinion ■ clips in sequence. Be careful not to skip any pinion clips or vanes. Vane Attachment Swivel Plate Swivel Plate ISSUE DATE: FEBRUARY 2018 ORIGINATOR: SKILTEC REPLACES ISSUE DATE: FEB 2018 APPROVED BY: S. GONZALEZ PAGE 18 OF 29...
- Page 19 Swivel plates attached on the left will have STD L on the top. Non-Control Rivet End Cap Rivet Swivel Arm Front Clip Swivel Plate Swivel Plate Side Stack Split Stack ISSUE DATE: FEBRUARY 2018 ORIGINATOR: SKILTEC REPLACES ISSUE DATE: FEB 2018 APPROVED BY: S. GONZALEZ PAGE 19 OF 29...
- Page 20 Re-attach the end treatment. Repeat the adjustment as necessary. ■ ISSUE DATE: FEBRUARY 2018 ORIGINATOR: SKILTEC REPLACES ISSUE DATE: FEB 2018 APPROVED BY: S. GONZALEZ PAGE 20 OF 29...
-
Page 21: Basic Operation
To deselect a group, press the group number again. The backlight for that group button will go out. 3. Press ▼ CLOSE to traverse the selected sheer(s) closed, covering the opening. ISSUE DATE: FEBRUARY 2018 ORIGINATOR: SKILTEC REPLACES ISSUE DATE: FEB 2018 APPROVED BY: S. GONZALEZ... -
Page 22: Basic Reset
12 seconds. Release the button. 2. Refer to “Joining a Sheer to a Group” on page 19 to program the sheer to a group. ISSUE DATE: FEBRUARY 2018 ORIGINATOR: SKILTEC REPLACES ISSUE DATE: FEB 2018 APPROVED BY: S. GONZALEZ... -
Page 23: Troubleshooting
Repeat as necessary until the end treatment hangs straight. See “Attach the End Treatment to the Swivel Plate” on page 18. ISSUE DATE: FEBRUARY 2018 ORIGINATOR: SKILTEC REPLACES ISSUE DATE: FEB 2018 APPROVED BY: S. GONZALEZ PAGE 23 OF 29... - Page 24 If so, use needlenose pliers to remove the metal bead, then move it down a notch and crimp it tightly closed. Swivel ISSUE DATE: FEBRUARY 2018 ORIGINATOR: SKILTEC REPLACES ISSUE DATE: FEB 2018 APPROVED BY: S. GONZALEZ PAGE 24 OF 29...
- Page 25 There are two methods for removing the motor shown on the following ■ page. Choose the one that works best for you. ISSUE DATE: FEBRUARY 2018 ORIGINATOR: SKILTEC REPLACES ISSUE DATE: FEB 2018 APPROVED BY: S. GONZALEZ PAGE 25 OF 29...
- Page 26 Rotate the headrail down as shown, until ■ Locking SofTrak ™ the headrail pops free from the bracket. Screw Headrail Tilt Down Loosen and Push Up ISSUE DATE: FEBRUARY 2018 ORIGINATOR: SKILTEC REPLACES ISSUE DATE: FEB 2018 APPROVED BY: S. GONZALEZ PAGE 26 OF 29...
-
Page 27: Cleaning Procedures
Deep Cleaning For deep cleaning, both injection/extraction and ultrasonic cleaning methods are recommended. CAUTION: Do not dry clean Luminette fabrics. ISSUE DATE: FEBRUARY 2018 ORIGINATOR: SKILTEC REPLACES ISSUE DATE: FEB 2018 APPROVED BY: S. GONZALEZ PAGE 27 OF 29... - Page 28 Hang fabrics immediately after cleaning with the vanes open and the loops evenly spaced. Allow the ■ fabric to drip dry completely. ISSUE DATE: FEBRUARY 2018 ORIGINATOR: SKILTEC REPLACES ISSUE DATE: FEB 2018 APPROVED BY: S. GONZALEZ PAGE 28 OF 29...
- Page 29 Minor wrinkles, puckers, or other variations can appear and are inherent to this textile product. ■ Such variations, like those just mentioned, are normal, acceptable quality. ■ ISSUE DATE: FEBRUARY 2018 ORIGINATOR: SKILTEC REPLACES ISSUE DATE: FEB 2018 APPROVED BY: S. GONZALEZ PAGE 29 OF 29...
Need help?
Do you have a question about the LUXAFLEX LUMINETTE and is the answer not in the manual?
Questions and answers