Simunition 5307570 Quick Start Manual

Yellow
White
sabot
sabot
Fig. I
9mm FX (left) and CQT (right)
® ®
G F
E
D
C
B
Fig. II
Conversion kit parts
Rounded-end
brass insertion tool
Fig. III
Fig. IV
Fig. V Fig. VI
Fig. VII
Fig. VIII
Simunition
for Submachine Guns HK MP5K PDW/N, HK MP5 N
Intended only for supervised training conducted in accordance with Simunition® safety training pro-
tocols by Law Enforcement, Military and Simunition® approved Commercial Range Programs.
The safe use of the 9 mm FX
sion kit. Proper installation of the kit is required to help preclude the inadvertent chambering of most 9
x 19 mm live, lethal ammunition and ensure the proper operation and cycling of the weapon. For safe-
ty reasons, conversion barrels are manufactured from the same quality steel as service barrels.
The conversion kit for HK MP5K PDW/N and HK MP5 N consists of seven parts: (Fig. II)
Part A: Simunition locking piece
®
Part C: Holding device
A
Part E: Tool handle
Part G: Removal tool

Installation

1. With the muzzle of the weapon pointed in a safe direction, remove magazine, lock back the bolt
assembly as per weapon OEM factory guidelines and visually inspect the chamber to verify that
it is unloaded.
2. Field strip the weapon and thoroughly clean the service barrel as per weapon OEM factory
guidelines.
3. Using the handle and insertion tool provided (Parts E & F), insert the sub-calibre barrel into the
service barrel from the breech end (Fig. III & IV). (Note the arrow stating "muzzle" on
Simunition sub-calibre barrel)
®
4. Holding the barrel group vertically, rest the tool handle on a hard surface (Fig. V).
IMPORTANT!! This contact will adjust the head space of the kit to your weapon for
functioning or
FX
®
result in improper cycling of the weapon and DAMAGE to the Simunition
barrel lip.
Place the holding device over the Simunition
group vertically with the tool handle in CONTACT with a hard surface. Starting with the screw
closest to the front sight of the MP5, use the provided allen key to FIRMLY tighten the hold-
ing device screws, alternately (Fig. VII).
IMPORTANT!! Failure to firmly tighten the holding device screws will result in
Simunition sub-caliber barrel movement during functioning followed by improper
®
cycling of the weapon and DAMAGE to the Simunition
IMPORTANT!! Keep the Holding device screws lubricated with oil or anti-seize to pre-
vent them from blocking without holding the Simunition
This could prevent the sub-caliber barrel from being damaged.
5. Separate the locking piece and the bolt face from the carrier. Replace the service locking piece
with the one provided in the Simunition
plied storage box. Reassemble the Simunition
OEM factory guidelines (Fig. VIII, IX, X).
Note: Press the bolt face and carrier together and observe the roller locks to ensure they are not
engaging.
6. Manually cycle the weapon and ensure all mechanisms are operational as per weapon OEM fac-
tory guidelines.
NOTE: For optimal function with the kit, SIMUNITION
and chamber be cleaned using a 9mm /.38/.357 caliber bore brass or stainless steel
brush after the firing of every 80 cartridges.

Returning the MP5 to service use:

1. With the muzzle of the weapon pointed in a safe direction, remove magazine, lock back the bolt
assembly as per weapon OEM factory guidelines and visually inspect the chamber to verify that
it is unloaded.
2. Field strip the weapon as per weapon OEM factory guidelines. Set the parts aside.
Conversion Kit
®
Product No. 5307570

Handling and Safety Instructions

and CQT cartridges requires the installation of the appropriate conver-
® ®
Part B:
Part D:
Part F:
ammunition. Failure to properly make this adjustment will
CQT
®
sub-calibre barrel (Fig. VI). Maintain the barrel
®
kit (Part A). Store the service locking piece in the sup-
®
locking piece and the carrier as per weapon
®
Allen key
Sub-calibre barrel
Insertion tool
sub-caliber
®
sub-caliber barrel lip.
®
sub-caliber barrel lip proprely.
®
recommends that the barrel
®
5307585.FTSIM (rev.10)