Table of Contents
Related Manuals for KegLand NukaTap KL21760
Summary of Contents for KegLand NukaTap KL21760
- Page 1 NukaTap Counter Pressure Bottle Filler Instruction Manual NukaTap Counter Pressure Bottle Filler Instruction Manual KL21760 KegLand Distribution PTY LTD www.KegLand.com.au www.KegLand.com.au Last Updated 27/07/2021 3:26 PM Page 1 of 13...
- Page 2 Do not exceed 15psi (100 kPa) • A leak test must be conducted upon initial setup. • Only use KegLand approved cleaning and sanitising chemicals such as StellarClean and StellarSan. Do not clean with harsh chlorinated cleaners. 50cm 8mm x 5mm EVABarrier Hose ¼”...
- Page 3 1 x ¼” Male x Push in Barb for Nukatap Spout 2 x ¼” Male x 6.35mm duotight (KL08730) 1 x Red Gas Male Ball Lock Post (KL10788) 1 x Yellow Liquid Male Ball Lock Post (KL10788-Yellow) www.KegLand.com.au Last Updated 27/07/2021 3:26 PM Page 3 of 13...
- Page 4 1. Screw the ¼” Male x Push in Barb for NukaTap Spout into the beer/liquid inlet of the NukaTap counter pressure bottle filler. 2. Push the barb into the NukaTap Spout to form a seal. www.KegLand.com.au Last Updated 27/07/2021 3:26 PM Page 4 of 13...
- Page 5 To determine whether the hose is secure, gently pull back on the hose. If the hose is easily removed then push it back into the fitting until seated. www.KegLand.com.au Last Updated 27/07/2021 3:26 PM Page 5 of 13...
- Page 6 1. Screw the ¼” Male x 8mm duotight fitting into the beer/liquid inlet of the NukaTap counter pressure bottle filler. 2. Push EVABarrier hosing from your keg into the 8mm duotight fitting on beer/liquid inlet of the counter pressure bottle filler. www.KegLand.com.au Last Updated 27/07/2021 3:26 PM Page 6 of 13...
- Page 7 3. Use EVABarrier hosing and two liquid ball lock disconnects (KL20749) to transfer beer from the FermZilla or keg to the NukaTap Counter Pressure Bottle Filler. www.KegLand.com.au Last Updated 27/07/2021 3:26 PM Page 7 of 13...
- Page 8 Gas inlet of the counter pressure bottle filler. 3. Use a grey ball lock disconnect (KL20756) to connect EVABarrier gas hosing from your regulator to the red gas male ball lock post. www.KegLand.com.au Last Updated 27/07/2021 3:26 PM Page 8 of 13...
- Page 9 If bubbles are formed at any of these connections this indicates a leak which needs to be fixed. Alternatively, the counter pressure bottle filler including all hose connections can be submersed in water. The formation of bubbles in the water indicates a leak. www.KegLand.com.au Last Updated 27/07/2021 3:26 PM Page 9 of 13...
- Page 10 FermZilla at 10-11 psi at 2°C for over 7 days. For a descriptive guide which explains how to keg your beer refer to our blog post: https://www.kegland.com.au/blog/post/how-to-keg-your-beer-a-basic-guide The colder the beer the less foaming you will get in the bottle and hence the faster you will be able to transfer.
- Page 11 This will allow liquid to begin flowing into the bottle again. Open the tap to begin the transfer of beer Open the large knurled bleed valve to allow some gas to escape when the flow of beer slows. www.KegLand.com.au Last Updated 27/07/2021 3:26 PM Page 11 of 13...
- Page 12 Once at step 8 the liquid ball lock disconnect for the beer inlet can be pushed onto the FermZilla, keg to begin the flow of beer. Once the bottle is full disconnect the beer supply by removing the ball lock disconnect from the FermZilla or keg. www.KegLand.com.au Last Updated 27/07/2021 3:26 PM Page 12 of 13...
- Page 13 If you purchased your unit from an international distributor, you will be required to go through their warranty claims process. Terms & Conditions For a full terms and conditions, please visit our website here -> www.KegLand.com.au Last Updated 27/07/2021 3:26 PM Page 13 of 13...
Need help?
Do you have a question about the NukaTap KL21760 and is the answer not in the manual?
Questions and answers