Advertisement
Table of Contents
ARMET OUTDOOR SCONCE WITH O1OA HANGING SYSTEM
These Instructions cover the ARMET luminaire with the following options:
HANGING
SERIES
SYSTEM
O1OA:
1. ARMET
OUTDOOR
(AT1)
SCONCE ADA
COMPLIANT
SCONCE
GENERAL NOTES:
1. PLEASE COMPLETELY READ THE INSTALLATION INSTRUCTIONS BEFORE STARTING INSTALLATION.
2. TURN OFF POWER TO CIRCUIT FIXTURE WHILE IT IS BEING INSTALLED.
3. INSTALL IN ACCORDANCE WITH ALL LOCAL, STATE AND NATIONAL CODES CONSULT WITH A QUALIFIED
ELECTRICIAN FOR PROPER INSTALLATION.
4. CAREFULLY UNPACK ALL CONTENTS; SOME COMPONENTS MAY HAVE BEEN SHIPPED IN SEPARATE BOXES
MOST FIXTURES ARE SHIPPED PARTIALLY ASSEMBLED. SOME UNASSEMBLY MAY BE REQUIRED FOR
INSTALLATION.
5. DO NOT LET THE LUMINAIRE HANG FROM THE WIRE CONNECTIONS.
6. DUE TO A CHANGE IN NEC SECTION 410.69 EFFECTIVE IN 2022, THE COLOR PINK WILL BE USED IN PLACE
OF GRAY FOR 0-10V CONTROL. NOTE THAT EXISTING SYSTEMS AND FIXTURES MANUFACTURED PRIOR TO
2022 MAY STILL USE GRAY WIRE AS AN UNGROUNDED CONDUCTOR FOR 0-10V CONTROL. CARE SHOULD
BE TAKEN WHEN WORKING ON EXISTING SYSTEMS.
INSTALLATION INSTRUCTIONS
LIGHT
SIZE
SOURCE
24"
36"
STATIC
48''
WHITE
60''
FIG. 1-AT1-O1OA-XX-XX-XXX-LEDX_XXK-
UNV-DM~
OCL Architectural Lighting
Phone: 314.863.1895
Fax: 314.863.3278
www.ocl.com
Sensitivity: Internal & Restricted
CONTROL
DM1: 0-10V DIM 1%
WIRE LABEL
TABLE
WIRE LABEL
TABLE ON
PAGE 6
Advertisement
Table of Contents
Related Manuals for OCL ARMET AT1-O1OA LED Series
Summary of Contents for OCL ARMET AT1-O1OA LED Series
- Page 1 OF GRAY FOR 0-10V CONTROL. NOTE THAT EXISTING SYSTEMS AND FIXTURES MANUFACTURED PRIOR TO 2022 MAY STILL USE GRAY WIRE AS AN UNGROUNDED CONDUCTOR FOR 0-10V CONTROL. CARE SHOULD BE TAKEN WHEN WORKING ON EXISTING SYSTEMS. OCL Architectural Lighting Phone: 314.863.1895 Fax: 314.863.3278 www.ocl.com...
- Page 2 Rev date: 17 JUN 2021 ARMET-O1OA-LED-INSTALLATION_INSTRUCTIONS Table of Contents GENERAL INFORMATION: ........................... 3 MOUNTING: ............................... 4 ARMET MOUNTING: ............................4 OCL Architectural Lighting Phone: 314.863.1895 Fax: 314.863.3278 www.ocl.com Page Sensitivity: Internal & Restricted...
- Page 3 ANCHOR SCREWS 2 QTY SEALING WASHER RED BAG 2 QTY INSTALLATION INSTRUCTION ANCHOR BODY 2 QTY FIG.3 - RED BAG AND INSTALLATION FIG.4 – MOUNTING HARDWARE INSTRUCTION MANUAL OCL Architectural Lighting Phone: 314.863.1895 Fax: 314.863.3278 www.ocl.com Page Sensitivity: Internal & Restricted...
- Page 4 Remove the END CAPS by unscrewing the CAP SCREWS and remove the DIFFUSER by sliding it outwards as shown in FIG. 6. CAP SCREWS (2 PLCS) DIFFUSER END CAPS FIG.6 – DIFFUSER DISASSEMBLY OCL Architectural Lighting Phone: 314.863.1895 Fax: 314.863.3278 www.ocl.com Page Sensitivity: Internal & Restricted...
- Page 5 BACK HOUSING as shown in FIG.8,9 &10. FIG.9– PLACEMENT OF ANCHORS J-BOX BUILDING SUPPLY WIRES J-BOX COVER BACK HOUSING ASSEMBLY FIG.10 – WIRING CONNECTION FIG.8 – JUNCTION BOX ASSEMBLY OCL Architectural Lighting Phone: 314.863.1895 Fax: 314.863.3278 www.ocl.com Page Sensitivity: Internal & Restricted...
- Page 6 SCONCE ADA TABLE ON 48” WHITE DIM 1% COMPLIANT LED2 PAGE 6 SCONCE 60’’ SEE GENERAL NOTE 6 ON PAGE 1 FIG. 12 – WIRE LABEL TABLE OCL Architectural Lighting Phone: 314.863.1895 Fax: 314.863.3278 www.ocl.com Page Sensitivity: Internal & Restricted...
- Page 7 10. Reattach the CAST ALUMINIUM CAPS and secure with the COUNTER SUNK SCREWS provided as shown in FIG.15. COUNTER SUNK SCREWS (2PLCS) DIFFUSER SIDE CHANNELS EXTRUDED BACK CHANNEL CAST ALUMINIUM CAPS (2 PLCS) FIG. 15 – CAPS ASSEMBLY FIG.14 – DIFFUSER ASSEMBLY OCL Architectural Lighting Phone: 314.863.1895 Fax: 314.863.3278 www.ocl.com Page Sensitivity: Internal & Restricted...
- Page 8 FIG. 16 – FINAL ASSEMBLY 12. Restore power to circuit the series is connected to. Test to see that the luminaire turns on after power is restored. b. Contact OCL for any luminaire troubleshooting if a problem occurs. FIG. 17-AT1-O1OA-XX-XX-XXX-LEDX_XXK- UNV-DM~ OCL Architectural Lighting Phone: 314.863.1895...
Need help?
Do you have a question about the ARMET AT1-O1OA LED Series and is the answer not in the manual?
Questions and answers