Subscribe to Our Youtube Channel
Related Manuals for OSS OSS-PCIe-HIB38-x8-DUAL
Summary of Contents for OSS OSS-PCIe-HIB38-x8-DUAL
- Page 1 PCIe x8 Gen3 Host Cable Adapter with PCIe Switch Model: OSS-PCIe-HIB38-x8-DUAL Installation Guide SKU: OSS-PCIe-HIB38-X8-DUAL www.onestopsystems.com...
-
Page 2: Table Of Contents
2.2 Software Requirement Installation Procedures Configure Dipswitches Install HIB Host card Install HIB Target card Install PCIe card Install x8 iPass cable 3.5.1 Connect Cable to Target card 3.5.2 Connect Cable to Host card 3.5.3 Use Case Diagrams OSS-PCIe-HIB38x8-DUAL | 2... - Page 3 One Stop Systems Connect ATX Power Supply Power ON the system Verify Hardware Target card LEDs Host card LEDs LED Indicators Software Installation How to Get More Help 6.1 Contacting Technical Support 6.2 Returning Merchandise 6.3 Online Support Resources OSS-PCIe-HIB38x8-DUAL | 3...
-
Page 4: Preface
Disclaimer: We have attempted to identify most situations that may pose a danger, warning, or caution condition in this manual. However, the company does not claim to have covered all situations that might require the use of a Caution, Warning, or Danger indicator. OSS-PCIe-HIB38x8-DUAL | 4... -
Page 5: Safety Instructions
Also, before connecting a cable, make sure both connectors are correctly oriented and aligned. CAUTION Do not attempt to service the system yourself except as explained in this manual. Follow installation instructions closely. OSS-PCIe-HIB38x8-DUAL | 5... - Page 6 Handle all sensitive components at an ESD workstation. If possible, use anti-static floor pads and workbench pads. Handle components and boards with care. Do not touch the components or contacts on a board. Hold a board by its edges or by its metal mounting bracket. OSS-PCIe-HIB38x8-DUAL | 6...
-
Page 7: Introduction
It operates in upstream or downstream mode with Dipswitch setting change. The host cable adapter installs in the PCIe slot of a host server and the target cable adapter installs in the Target slot / Upstream slot of the OSS backplane. -
Page 8: Overview
Overview This is an overview of the HIB38-X8-DUAL board (OSS-386). *The OSS-386 “mezzanine slot connector” is mainly for attaching a daughter card / mezzanine card (OSS-390) with additional two x8 PCIe cable connector to use a QUAD host card (HIB38-x8-QUAD). -
Page 9: Pcie Card Edge X8
ON – Link is UP, 8.0 GT/s Gen3- solid green (8.0GT/s) Gen2 - Blinking frequency: 2Hz (5.0GT/s) Gen1 - Blinking frequency: 1Hz (2.5GT/s RED – No link from the Host side or Target side; Fatal error on PCIe switch; OSS-PCIe-HIB38x8-DUAL | 9... -
Page 10: Board Leds
Board LEDs There are two LEDs on the HIB38-x8. They are located in the upper right of the board. PWRGD--Power good, board has power CE LINK—Card edge, successful link with the card edge 1.10 Block Diagram OSS-PCIe-HIB38x8-DUAL | 10... -
Page 11: Dimensions
#1=ON ; #2=OFF ; #3=OFF ; #4=OFF ; #5=OFF and #6 =OFF When the card dipswitch is configured as Host mode, do not install the card in a target slot (Upstream slot) on the OSS expansion backplane. OSS-PCIe-HIB38x8-DUAL | 11... -
Page 12: Pci Express X8 Card Edge Connector Pin Outs
Transmitter differential pair, Lane 6 Ground Ground PERp6 Ground PERn6 Receiver differential pair, Lane 6 PETp7 Ground PETn7 Transmitter differential pair, Lane 7 Ground Ground PERp7 PRSNT2# Hot-Plug presence detect PERn7 Receiver differential pair, Lane 7 Ground Ground OSS-PCIe-HIB38x8-DUAL | 12... -
Page 13: X8 Cable Wire Connections / Pin Outs
CREFCLK- PWR (3.3V) PWR (3.3V) RSVD PWR RTN RSVD PWR RTN SB_RTN PWR RTN CPSRNT$# CWAKE# CPWRON CPERST# PETp4 PETp4 PETn4 PERp4 PETp5 PERp5 PETn5 PERn5 PETp6 PERp6 PETn6 PERn6 PETp7 PERp7 PETn7 PERn7 *NC: Not Connected OSS-PCIe-HIB38x8-DUAL | 13... -
Page 14: X8 Cable Signal Descriptions
Power: Provides local power for in-cable redriver circuits. Only needed on long cables (Power does not go across the cable.) PWR_RTN Po Provides local power return path for PWR pins. CWAKE# Cable WAKE CPERST# Cable PCI Express Reset OSS-PCIe-HIB38x8-DUAL | 14... -
Page 15: Hardware Requirements
One or two x8 iPass cable(s). When connecting two external expansion unit, you need two x8 iPass cable. OSS Expansion chassis with Gen3 backplane, or OSS expansion backplane and power supply (one or two expansion unit). 2.1.1 HIB38-x8-DUAL card (Host and Target) A pair of HIB38-x8-DUAL card (Target and Host cards) 2.1.2... -
Page 16: Expansion Chassis / Backplanes
2.1.5 ATX Power Supply If you are using an OSS backplane with the HIB38-x8-DUAL card, you need a power supply unit to provide power. A standard ATX power supply will work with the boards. Software Requirement Computer running Windows 7, 8, 10 and or Server... -
Page 17: Installation Procedures
Power down the host computer first before installing the host card. Do not install the host card while the computer is ON. Install the HIB38-x8-DUAL host card into the available PCIe slot in the computer’s motherboard. Use a x16 Gen3 PCIe slot. Make sure to secure the card. OSS-PCIe-HIB38x8-DUAL | 17... -
Page 18: Install Hib Target Card
Do not plug in the target card while expansion unit or the expansion backplane is ON as this can damage the board. Turn OFF the unit first before installing the card. The HIB Target card will only work in the OSS backplane “Upstream” slot. It will not function in the downstream slot or the end-point slot of the backplane. -
Page 19: Install Pcie Card
Photos below are example of different backplanes showing where the locations of the “Upstream” slot. Install PCIe card Plug-in your third party PCIe card in the expansion backplane. Use the downstream slot on the OSS backplane. See photos below for the location of the downstream slot / end-point slot on the backplane. -
Page 20: Install X8 Ipass Cable
Plug in the other end of the two cables to the Host card. If you are only connecting a single cable (for one expansion unit), you can use either the top or bottom port of the host card. OSS-PCIe-HIB38x8-DUAL | 20... -
Page 21: 3.5.3 Use Case Diagrams
The HIB38-x8 Dual card (target) is not compatible on different brand or another backplane. The HIB38-X8 Dual target card will not work on a different backplane. Connecting the HIB38-X8 Dual host card directly to unknown end-point device or a non-OSS backplane is not supported. OSS-PCIe-HIB38x8-DUAL | 21... - Page 22 The cable on the host side (Host Computer) can be connected to either top or bottom external cable connector. The cable on the target side (OSS Expansion Unit), can be only attached to the top connector. OSS-PCIe-HIB38x8-DUAL | 22...
-
Page 23: Connect Atx Power Supply
If you are using an expansion chassis, the power supply is already part of the unit. You can skip this step. If you are using an expansion backplane, plug-in the ATX power supply cable into the 24pin ATX power connector on the OSS board. -
Page 24: Power On The System
If the expansion unit or the HIB card are not powering ON, check the link cable make sure it is firmly connected. The target and host card must be fully seated in the PCIe slot in order to work correctly. Check the Dipswitch is set correctly on each card. OSS-PCIe-HIB38x8-DUAL | 24... -
Page 25: Verify Hardware
Bracket LED : Solid green – Gen 3 or Blinking green – Gen 2 (Blinking frequency: 2Hz ). Gen1 (Blinking frequency: 1Hz) Board LEDs : PWRGD – Solid green CE LINKED – Solid green or blinking green, depending on the blink rate. Gen3- solid green Gen2 - Blinking frequency: 2Hz Gen1 - Blinking frequency: 1Hz OSS-PCIe-HIB38x8-DUAL | 25... -
Page 26: Led Indicators
One Stop Systems LED Indicators Green – Successful link between host and target Red – Fatal error on PCIe switch. Indication of faulty connection. No LED – No power. No link. OSS-PCIe-HIB38x8-DUAL | 26... -
Page 27: Software Installation
One Stop Systems Software Installation No software or driver is required for the Host Adapter card. OSS-PCIe-HIB38x8-DUAL | 27... -
Page 28: How To Get More Help
If you need technical support, product assistance or have a technical inquiry we encourage you to submit it on-line using our Technical Support Form. If you need to send a unit for repair or diagnostic evaluation, fill out our RMA (Return Material Authorization) online request form. https://www.onestopsystems.com/support OSS-PCIe-HIB38x8-DUAL | 28... - Page 29 One Stop Systems OSS-PCIe-HIB38x8-DUAL | 29...
Need help?
Do you have a question about the OSS-PCIe-HIB38-x8-DUAL and is the answer not in the manual?
Questions and answers