Subscribe to Our Youtube Channel
Related Manuals for Shimafuji Electric CCPF-SK
Summary of Contents for Shimafuji Electric CCPF-SK
- Page 1 CCPF-SK Assembly instructions Rev 1.01 Document No.310898001 Date 15 September, 2021 Shimafuji Electric Inc. Printed in Japan...
- Page 2 Revision History Edition Date Contents Remarks Number...
-
Page 3: Table Of Contents
Table of Contents Introduction ........................... 3 Contents confirmation ........................3 Disassembling R-Car Starter Kit ....................8 Assembling (board) ........................10 Assembling (bottom plate) ......................14 Assembling (FAN cable, micro-USB cable, upper plate) ............16 Completed product ........................21... -
Page 4: Introduction
1. Introduction This is the material for assembling CCPF-SK. Please wear an antistatic wire when working. CCPF-SK supports both R-Car Starter Kit Premier(H3) and R-Car Starter Kit Pro(M3), but this Assembly instructions uses R-Car Starter Kit Premier(H3). 2. Contents confirmation... - Page 5 Make sure that you have all the necessary parts to manufacture one CCPF-SK. Picture 2-3 R-Car Starter Kit Premier(H3) Picture 2-4 PCB Picture 2-5 upper plate of the housing...
- Page 6 Picture 2-6 bottom plate of the housing Picture 2-7 M3 spacer: 5 KSB-318ANE (1 spare) Picture 2-8 M3 countersunk head screw: 5 BF-0304 (1 spare)
- Page 7 Picture 2-9 M3 pan head screw: 9 B-0305-S1 (1 spare) Picture 2-10 M2.6 pan head screw: 9 B-2606-S1 (1 spare) Picture 2-11 M2.6 spacer: 5 ASB-2608E (1 spare)
- Page 8 Picture 2-12 micro-USB2.0 micro-B cable Please prepare the following tools individually. Picture 2-13 phillips screwdriver(L[M3], M[M2.6]), wrench(5mm、6mm), nut driver(5mm)
-
Page 9: Disassembling R-Car Starter Kit
Disassembling R-Car Starter Kit Picture 3-1 prepare R-Car Starter Kit Picture 3-2 extract R-Car Starter Kit from its box Picture 3-3 remove spacers, screws, and the acrylic plates from R-Car Starter Kit... - Page 10 Picture 3-4 use the board in the red frame Picture 3-5 retain the removed the acrylic plates, spacers, and screws unused...
-
Page 11: Assembling (Board)
4. Assembling (board) Picture 4-1 upper side of R-Car Starter Kit Picture 4-2 bottom side of R-Car Starter Kit Picture 4-3 tighten in four places with the included M2.6 spacers and M2.6 pan head screws... - Page 12 Picture 4-4 upper side of PCB Picture 4-5 bottom side of PCB Picture 4-6 tighten in four places with the included M3 spacers and M3 pan head screws PCB side Picture 4-7 make sure that the counter sinking are on the bottom plate side...
- Page 13 Picture 4-8 upper side of R-Car Starter Kit IN(Stack） Picture 4-9 attach the CN1 of R-Car Starter Kit to the CN1 of PCB Picture 4-10 board connection...
- Page 14 PUSH Picture 4-11 press with fingers from above Make sure there are no gaps. Picture 4-12 tighten four M2.6 spacers to PCB with M2.6 pan head screws from the back side If you need the M.2 and camera, you should attach them at this stage. Picture 4-13 side of connection...
-
Page 15: Assembling (Bottom Plate)
5. Assembling (bottom plate) UP（ON） Picture 5-1 turn on the POWER switch PULL PULL Picture 5-2 insert the POWER switch side into the housing and put with opening the bottom plate of the button side while aligning the MIC and LINE holes. DOWN（OFF）... - Page 16 Picture 5-4 tighten the bottom plate of the housing with four M3 countersunk screws USB connector Picture 5-5 top of assembly...
-
Page 17: Assembling (Fan Cable, Micro-Usb Cable, Upper Plate)
6. Assembling (FAN cable, micro-USB cable, upper plate) Picture 6-1 FAN cable on R-Car Starter Kit Picture 6-2 connect FAN cable from R-Car Starter Kit to PCB CONNECT Picture 6-3 R-Car Stater Kit (CN12) - Page 18 CONNECT Picture 6-4 connect one side with the included micro-USB cable CONNECT Picture 6-5 PCB (CN11) CONNECT Picture 6-6 connect the other side with the included micro-USB cable...
- Page 19 Picture 6-7 example of cable connection (top) Picture 6-8 example of cable connection (side) Picture 6-9 2 pattern cable connection...
- Page 20 Picture 6-10 cover the bottom plate with the upper plate Picture 6-11...
- Page 21 Picture 6-12 Picture 6-13 tighten the sides of the housing with four M3 pan head screws...
-
Page 22: Completed Product
7. Completed product Picture 7-1 side (right) Picture 7-2 back side Picture 7-3 side (left) - Page 23 Picture 7-4 front Picture 7-5 bottom It is recommended to apply thread lock to each screw. End of document...
Need help?
Do you have a question about the CCPF-SK and is the answer not in the manual?
Questions and answers