Bame DELMA Installer Manual
  1. Manuals
  2. Brands
  3. Bame Manuals
  4. Control Systems
  5. DELMA
  6. Installer manual

Bame DELMA Installer Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
ELECTROMECHANICAL ROAD BARRIERS
FOR 2,5 MT, 4 MT, 5 MT, 6 MT
ENTRANCES
24 Vcc INTENSIVE USE
230 Vac RESIDENTIAL USE
Installer manual
rev. 3 03/12
READ CAREFULLY BEFORE PROCEEDING
WITH INSTALLATION
KEEP THIS MANUAL FOR FUTURE USE
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the DELMA and is the answer not in the manual?

Questions and answers

Related Manuals for Bame DELMA

Summary of Contents for Bame DELMA

  • Page 1 ELECTROMECHANICAL ROAD BARRIERS FOR 2,5 MT, 4 MT, 5 MT, 6 MT ENTRANCES 24 Vcc INTENSIVE USE 230 Vac RESIDENTIAL USE Installer manual rev. 3 03/12 READ CAREFULLY BEFORE PROCEEDING WITH INSTALLATION KEEP THIS MANUAL FOR FUTURE USE...
  • Page 2 Safety Electromechanical road barriers for passages from 2,5 mt up to 6 mt. with low voltage electric motors for intensive use and extensible standard aluminium round arm. The cabinet treated with electrophoresis and painted in epoxy powder can be used in any climatic condition. specifications Available with mobile foot and articulated arm.

  • Page 3: Assembling Procedure

    ATTENTION: BAME s.r.l. is liable only for the individual articles produced and sold by BAME. The gate with the motor it’s considered a machine and must respect the machinery directives, the installer must verify the safety of the gate with the motor and is liable for any damage due to a poor installation.
  • Page 4 Right barrier with the arm in vertical Operations to transform a right barrier into position a left barrier PART. A PART. A PART. B PART. C PART. D 1. Disconnect the power supply of the barrier 2. Unlock the motor 3.
  • Page 5 Emergency unlocking system: WARNING: DO NOT UNLOCK THE ATTENTION: BARRIER WITHOUT THE ARM. THIS SHEET MUST BE THERE IS A MORTAL DANGER IF CONSIGNED TO THE CLIENT THE BARRIER IS UNLOCKED WITHOUT THE ARM. 1. Open the protection panel using the key in the kit (fig. 6) 2.

  • Page 6: Safety Checks

    Safety checks IMPACT Checks: The ruggedness and the fastening of the structure is adeguate. The swing can not fall in the ground. CRUSHING The threshold of the gate it’s modeled not to create hindrance. Limit switch are installed and verified. The moving parts are equipped with adeguate protections installed in compliance with the safety standards.

  • Page 7: Declaration Of Conformity

    Declaration of conformity (must be filled by the installer) DECLARATION OF CONFORMITY “A” The undersigned Name: ......................Surname:..................... responsible of the installation of the system declare that the product: Gate type: ..............Address: ..............................satisfies all the technical regulations applicable to the product within the scope of Council Directives 73/23/EEC, 89/336/EEC, 98/37/EEC and subsequent modifications.
  • Page 8 Declaration of conformity DECLARATION OF CONFORMITY “B” BAME srl Via Leonardo da Vinci, 23 46020, San Giacomo Segnate (MN) Italia declare that the product motoreducer for sliding gates, see the instruction manual for compatible gates BARRIERA satisfies all the technical regulations applicable to the product within the scope of Council Directives: MACHINERY DIRECTIVE 98/37/CEE AND SUBSEQUENT MODIFICATIONS.

  • Page 9: Arm Support

    4. Lock the motor IT IS ADVISED TO USE 5. Release the arm and make sure that the arm does not go up by itself YS BAME ORIGINAL PROFILES. 6. Add other pieces of the arm as shown in the following page 7.
  • Page 10 Arm stikers and cap Assembling round alluminium arm 2,5 mt Single round arm 3 mt (transit width 2,70 mt) Fix the two parts of the arm whit a 4,8x16 self-threading screws FIG.9 Arm dimensions 4 mt Round telescopic arm Diameters: Min 3,80 mt (transit width 3,5 mt) - Max 4,30 mt (transit width 4 mt) 1) 75 x 2 x 3000 mm 2) 70 x 2 x 2000 mm...

  • Page 11: Adjusting The Spring Tension

    Adjusting limit switches and rubber stoppers Adjust the rubber stoppers and the switches so that the arm is horizontal when in closed position and vertical when in open position. PART. A PART. C FIG.10 Adjusting the spring tension: After having installed the arm on the barrier is mandatory to adjust the spring tension : 1.Unlock the reducer 2.Set the arm in the opening position 3.Lock the reducer...

  • Page 12: Warranty

    It is forbidden to replace any electric, electronic or mechanic part with not e-mail:info@bame.it original spare parts. BAME s.r.l. , has the right to modify or change the electronic boards and Grottazzolina (FM) 63844, Italy manuals, without prior notice.

Table of Contents