Table of Contents
Advertisement
Quick Links
INSTALLATION AND OPERATING INSTRUCTIONS
PumpSpy
The PumpSpy System requires a 12V Deep Cycle Battery (not included), 40 amp/hr
minimum, 75 amp/hr or higher recommended. SLA/AGM Battery strongly recommended.
READ ALL INSTRUCTIONS CONTAINED IN THIS MANUAL BEFORE USING THIS PRODUCT.
Save these instructions for future reference. Failure to read and follow the warnings and instructions
within this instruction manual could result in property damage, serious injury or death.
Contact Tech Support:
PS2000UG
™
IMPORTANT!
CELLULAR CONVERSION KIT
24/7 AUTOMATED REMOTE SUMP PUMP MONITORING
SPECIFICATIONS
System Solid State Pump Controller
Power Supply Requirements
Electrical Ratings
Relative Humidity
Storage Temperature
Operating Temperature
(833) 786-7779 support@pumpspy.com
120 VAC, 60 Hz,
15 AMP
12Amps @ 120 VAC;
18 Amps @ 12 VDC
0 to 80%
0° to 70°C
0° to 50°C
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for PumpSpy PS2000UG
Summary of Contents for PumpSpy PS2000UG
- Page 1 0° to 50°C PumpSpy PS2000UG ™ The PumpSpy System requires a 12V Deep Cycle Battery (not included), 40 amp/hr minimum, 75 amp/hr or higher recommended. SLA/AGM Battery strongly recommended. IMPORTANT! READ ALL INSTRUCTIONS CONTAINED IN THIS MANUAL BEFORE USING THIS PRODUCT.
-
Page 2: Safety First
WARNING! Do not use an extension cord. Extension cords could present a safety hazard if not properly sized, become damaged or the connection falls into the sump pit. Do not attempt to disassemble the PumpSpy controller. There are no field serviceable parts or repair options! RISK OF EXPLOSION. TO REDUCE THIS RISK, OBSERVE THE FOLLOWING WARNINGS: WARNING! Do not use to pump flammable or explosive liquids such as gasoline, fuel oil, kerosene, etc. -
Page 3: Installation
PumpSpy at (833) 786-7779 for assistance. ™ The PumpSpy System requires a 12V Deep Cycle Battery with a minimum 40 AMP/HR rating, 75 AMP/HR rating (or higher) recommended. AGM Battery is strongly recommended. INSTALLATION Electric shock hazard. DISCONNECT power before servicing. -
Page 4: Alarm Mute Button
STATUS INDICATOR REFERENCE CHART Use the chart below to identify the message associated with = Yellow = Blinking Red the color of each LED light on the PumpSpy Controller. = Red = Red/Green Alternating WATER LEVEL No Cycle Recorded High Water Alert... - Page 5 Less than 40 dB Net Weight (kgs) INSTALLATION & INITIAL STARTUP Inspect this unit before beginning installation. Occasionally, products are damaged during shipment. If any components are damaged, contact PumpSpy at (833) 786-7779 for assistance. ™ PLACEMENT & STORAGE CONDITIONS Install the UPS in a protected area that is free of excessive dust and has adequate air flow.
-
Page 6: Important Safety Warnings
INSTALLATION & INITIAL STARTUP (CONTINUED) CONNECT TO MODEM AND ROUTER Plug in your modem and wireless router into the receptacles on the rear panel of the UPS. Push the power button on the front of the unit. Connected devices will now be protected by the UPS. CAUTION! NEVER connect a laser printer or scanner to the UPS unit. -
Page 7: Troubleshooting
TROUBLESHOOTING WARNING! Always disconnect the power unit from power sources before handling. This guide is designed to help identify reasons for potential operating problems. It is not a service guide. Dismantling of the unit voids warranty. Servicing of the unit should be referred to the factory or its authorized service center. -
Page 8: Limited Three-Year Warranty
God, nature, vandalism or other acts beyond the control of PumpSpy™, owner’s acts or omissions, use outside the country in which the product was initially purchased and resales of the product by the original owner. This warranty does not cover pick up, delivery, transportation or house calls.
Need help?
Do you have a question about the PS2000UG and is the answer not in the manual?
Questions and answers