Advertisement
Quick Links
Advertisement
Related Manuals for Level 1 Lasers A604
Summary of Contents for Level 1 Lasers A604
- Page 1 A604 Rotating Laser Level Auto Levelling Model: A604...
-
Page 2: Table Of Contents
CONTENTS User Safety and Contents A604™ Diagram Operating Instructions Batteries & Power Rotation Speed & Side Mount Vertical Operation & Specifications LR700 Receiver Warranty User Safety • Laser output sign lies near the output aperture. • Do not stare directly into laser beam. • Do not disassemble the instrument or attempt to perform any internal servicing. Repairs and service should be performed only authorised service centres of Redback Lasers. • This instrument complies with the safety Classification standards of laser radiation. CAUTION: Class II laser <1mW at 635nm. -
Page 3: A604™ Diagram
A604 INTRODUCTION A604 Laser Unit 1. Control Panel 2. Dot Laser Output 3. Rotating Laser Output 4. Pendulum Lock 5. Vial for Vertical Rotation Mode 6. DC Input (optional Power Supply) 7. Battery Compartment 6x “AA” 8. Tripod 5/8”-11tpi Mount Side Plate Attachment Lever Adjustment Pin 5/8” – 11tpi Screw www.level1lasers.com.au... -
Page 4: Operating Instructions
A604 OPERATING INSTRUCTIONS Battery Instructions The A604 operates on 6 x standard Alkaline “AA” batteries, simply un- screw the battery compartment where indicated and insert batteries in the direction shown. Turning Laser On For Levelling (Horizontal Operation) Place laser on Tripod or on a stable surface, rotate the pendulum locking knob to the un-locked position (marked as “ON”) then press the power button on the control panel. The laser will auto level, the laser head will... -
Page 5: Rotation Speed & Side Mount
A604 OPERATING INSTRUCTIONS Rotation Speed The A604 has three rotation speeds (Low, Medium and High), under normal conditions high speed is recommended when using the LR700 electronic receiver. If you are using the laser indoors visibly a slower rotation speed may increase the visibility of the line produced. Rotation speed is changed by pressing the speed button on the control panel an LED light will indicate the selected speed, further presses of this button wil toggle between the three available speeds. Side Mount Plate The Side Plate can be used in two ways; firstly as a wall mount in horizontal levelling mode and secondly as a side mount for vertical rotation mode. The plate clips onto the bar at the back of the A604 laser and is removed by pressing the attachment level. www.level1lasers.com.au... -
Page 6: Vertical Operation & Specifications
A604 OPERATING INSTRUCTIONS Vertical Rotation Mode (Manual Levelling) The A604 can be placed on its side with the side mount plate attached and used for vertical rotation, this can be handy for any indoor vertical alignment off the rotating beam. To operate the A604 in vertical rotation mode DO NOT unlock the pendulum, leave it in the “OFF” position, use the adjustment screw on the side mount to level off the bubble vial on the A604. Once the bubble is central in the vial press the power button on the laser and the laser head will begin to rotate, the rotating beam being a vertical line and the dot beam being level. Another application where the vertical mode can be usefull is site squaring by aligning the dot laser beam along one axis of the 90 degree square and then using the receiver to pick up the rotating beam which is at 90 degrees to the dot laser beam. Laser Wavelength 635nm <1mW Laser Class Range with LR700 Receiver 240m diameter Accuracy ±4mm/20m Self Levelling Range ±3 IP Dust Water Resistance IP54 Workin Temperature C to +40 (in shade) Power 6 x “AA” Alkaline Low Power Power LED Flash Size... -
Page 7: Lr700 Receiver
A604 OPERATING INSTRUCTIONS LR700 Receiver operation The LR700 is an electronic laser receiver/detector and comes with a staff clamp bracket which allows you to attach the receiver to a measuring staff. Bubble Vial Laser Reception LED indicators Window Power Speaker Power up by pressing the power button, hold the receiver so the reception window is facing the rotating laser (upright for horizontal and on its side for vertical rotation). When the reception window is level with the rotating... -
Page 8: Warranty
12 Month WARRANTY - LEVEL 1 LASERS CMI Industries Pty Ltd provides consumers with a warranty to our products, this is in addition to requirements of any relevant legislation such as the Competition and Consumer Act 2010. Definitions: “CMI”, “We” or “Our” “Level1Lases” refers to CMI Industries Pty Ltd (ABN 29 102 713 922) of 8 Autumn St, Geelong West, Victoria 3218 ph (03) 5228 0777 “You” or “Consumer” refers to the initial purchaser of the product. “Product” refers to goods manufactured by or for CMI Industries Pty Ltd under the brand of Level1Lasers. “Material” refers to material or component used in the construction and manufacture of the product. “Workmanship” refers to handling, assembly and manufacturing processes done by or for CMI Industries Pty Ltd in order to manufacture the products. “Warranty Period” For Level1Laser Products is 12 Months. Warranty period is from original purchase date, no extension is made in the event of warranty replacement products supplied or time spent being repaired. Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. CMI warrants that our products will be free from defects in material and workmanship for the warranty period. CMI promises to repair or replace, free of charge, the product or part of product if found to be faulty due to defective workmanship or materials within the duration of the warranty as long as the following terms and conditions are met; • Product must not have been misused or abused, must not have incurred accidental damage or had un-authorised repair or tampering that has caused or contributed to its fault or failure. • You must contact CMI by phone, mail or email immediately when a fault or defect has become apparent and within the warranty period. • Product must be returned to store of purchase or directly to CMI, we will cover cost of postage only when sent by our reply paid Australia Post service (Australian Main land and Tasmania only) details will be provided upon phone, post or email communications with us. • CMI will cover cost of freight back of repaired or replaced product to original purchase store or you directly (depending on how it was sent Australian Main Land and Tasmania only). • CMI will determine whether to repair or replace the product or part of product on a case by case basis.