Advertisement
Quick Links
Advertisement
Summary of Contents for Level 1 Lasers MANUAL1
- Page 1 Rotating Laser and Electronic Receiver Model: MANUAL1...
-
Page 2: Operating Instructions
• This instrument complies with the safety Classification standards of laser radiation. CAUTION: Class II laser <1mW at 635nm. Do NOT stare into laser beam or aim at another person. Follow relevant Australian Standards MANUAL1™ Included Accessories • MANUAL1™ Laser Unit • Protective Carry Case • Standard “AA” Batteries • LR700 Electronic Receiver & Clamp •... - Page 3 MANUAL1 INTRODUCTION MANUAL1 Laser Unit 1. Control Panel 2. Dot Laser Output 3. Rotating Laser Output 4. Horizontal Levelling Vial 5. Tripod 5/8”-11tpi Mount 6. Base Locking Knob 7. Vial for Vertical Rotation Mode 8. Levelling Wheel 9. DC Input (optional power supply) www.level1lasers.com.au...
- Page 4 MANUAL1 OPERATING INSTRUCTIONS Battery Instructions The MANUAL1 operates on 4 x standard Alkaline “AA” batteries, first remove laser unit from levelling base by un-screwing the orange locking knob. Then un-screw the battery compartment where indicated and insert batteries in the direction shown. Levelling and Turning on Laser (Horizontal Operation) Place laser on Tripod then level the laser by rotating the levelling wheels for both “X” and “Y” axis until both top vials show the bubble exactly central (NOTE: the more accurate you are at setting the vials the more accurate the level will be). Once level power up using the red power button the head will rotate and laser emit. “X” Axis “Y” Axis www.level1lasers.com.au...
- Page 5 Arrow Buttons Power Button Scan Button Vertical operation The MANUAL1 can be operated on its side to produce a vertical rotating beam, this used in conjunction with the scan mode is ideal for indoor vertical alignment jobs. To use the MANUAL1 in vertical mode remove laser unit from base by un- screwing the orange locking knob then replace laser on its side (you will notice the location lugs on the rubber houseing). To level use the now “Z” axis levelling wheel and the single “Z” axis bubble vial, again make sure bubble is exactly central in the vial.
- Page 6 MANUAL1 OPERATING INSTRUCTIONS Vertical Operation Site Layout The MANUAL1 can be used for site squaring by aligning the dot laser beam along one axis of the 90 degree square and then using the receiver to pick up the rotating beam which is at 90 degrees to the dot laser beam. 90 degrees Laser Wavelength 635nm <1mW Laser Class Range with LR700 Receiver 240m diameter Accuracy ±4mm/20m Scan Modes IP Dust Water Resistance IP32 Workin Temperature C to +40 (in shade) Power 4 x “AA” Alkaline Low Power Power LED Flash Weight...
- Page 7 MANUAL1 OPERATING INSTRUCTIONS LR700 Receiver operation The LR700 is an electronic laser receiver/detector and comes with a staff clamp bracket which allows you to attach the receiver to a measuring staff. Bubble Vial Laser Reception LED indicators Window Power Speaker Power up by pressing the power button, hold the receiver so the reception window is facing the rotating laser (upright for horizontal and on its side for vertical rotation). When the reception window is level with the rotating...
- Page 8 12 Month WARRANTY - LEVEL 1 LASERS CMI Industries Pty Ltd provides consumers with a warranty to our products, this is in addition to requirements of any relevant legislation such as the Competition and Consumer Act 2010. Definitions: “CMI”, “We” or “Our” “Level1Lases” refers to CMI Industries Pty Ltd (ABN 29 102 713 922) of 8 Autumn St, Geelong West, Victoria 3218 ph (03) 5228 0777 “You” or “Consumer” refers to the initial purchaser of the product. “Product” refers to goods manufactured by or for CMI Industries Pty Ltd under the brand of Level1Lasers. “Material” refers to material or component used in the construction and manufacture of the product. “Workmanship” refers to handling, assembly and manufacturing processes done by or for CMI Industries Pty Ltd in order to manufacture the products. “Warranty Period” For Level1Laser Products is 12 Months. Warranty period is from original purchase date, no extension is made in the event of warranty replacement products supplied or time spent being repaired. Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. CMI warrants that our products will be free from defects in material and workmanship for the warranty period. CMI promises to repair or replace, free of charge, the product or part of product if found to be faulty due to defective workmanship or materials within the duration of the warranty as long as the following terms and conditions are met; • Product must not have been misused or abused, must not have incurred accidental damage or had un-authorised repair or tampering that has caused or contributed to its fault or failure. • You must contact CMI by phone, mail or email immediately when a fault or defect has become apparent and within the warranty period. • Product must be returned to store of purchase or directly to CMI, we will cover cost of postage only when sent by our reply paid Australia Post service (Australian Main land and Tasmania only) details will be provided upon phone, post or email communications with us. • CMI will cover cost of freight back of repaired or replaced product to original purchase store or you directly (depending on how it was sent Australian Main Land and Tasmania only). • CMI will determine whether to repair or replace the product or part of product on a case by case basis.