Subscribe to Our Youtube Channel
Related Manuals for Link LD-8
Summary of Contents for Link LD-8
- Page 1 Revision 0 June 2011 LD-8 Inner/Outer Thigh Owner’s Manual Serial Number Here Date of Purchase www.batcafitness.com LD-8 Owner’s Manual 1207 New Hope Road, Raleigh, NC - 919.255.1233 - www.batcafitness.com...
- Page 2 Instructions Congratulations on the purchase of your new Batca LD-8. This gym will provide you with a lifetime of enjoyment to meet your strength training needs. Batca Fitness Systems strives to build the best quality gyms and to package these gyms in such a way to avoid any damage during shipping.
-
Page 3: Table Of Contents
Frame Components Accessories ITEM NO. PART NUMBER DESCRIPTION QTY. ITEM PART NUMBER DESCRIPTION QTY. BFM-51173 Weight Stack Pull Pin BFP-10928 LD-8 Short Cage BFP-10921 Base Assembly Upholstery BFP-10888 Guide Rod Plate Guide Rod BFP-51827 BFP-10889 Top Weight Plate ITEM PART NUMBER DESCRIPTION QTY. - Page 4 Bolt Length Note: Bolt length is measured from the underside of the head of the bolt. Batca Fitness Systems LD-8 Owner's Manual...
- Page 5 LD-8 Owner’s Manual...
- Page 6 Batca Fitness Systems LD-8 Owner's Manual...
- Page 7 LD-8 Owner’s Manual...
-
Page 8: Short Cage
FLAT WASHER. DO NOT TIGHTEN BOLTS UNTIL STEP 2 Figure 1 Item # Part # Description BFP-10928 LD-8 Short Cage BFP-10921 Base Assembly BFP-51750 SHCS 3/8” x 2 3/4” BFH-50146 3/8” Flat Washer BFH-50157 3/8” Nylock Batca Fitness Systems... -
Page 9: Guide Rod Plate
SHCS 3/8” x 3 1/4” otherwise noted. Anywhere a washer is against the BFH-50146 3/8” Flat Washer round side of a tube there is to be a 3/8” CURVED WASHER instead of a 3/8” FLAT WASHER. BFH-50157 3/8” Nylock www.batcafitness.com LD-8 Owner’s Manual... -
Page 10: Weight Stack To Lower Cam Cable
SHCS 3/8” x 2 1/4” washer is against the round side of a BFH-50146 3/8” Flat Washer tube there is to be a 3/8” CURVED WASHER instead of a 3/8” FLAT BFH-50157 3/8” Nylock WASHER. Batca Fitness Systems LD-8 Owner's Manual... -
Page 11: Bfh-50253
(There should be approximately 1/2” to 1” between the arms). Position Pull Pin in Slot #1 as shown. Position belt on sprocket and adjust 3/8” Nylocks for Belt Tension. www.batcafitness.com LD-8 Owner’s Manual... - Page 12 Anywhere a washer is against BFP-51748 SHCS 3/8” x 3 1/4” the round side of a tube there is to be a 3/8” CURVED WASHER instead of a 3/8” FLAT BFH-50146 3/8” Flat Washer WASHER. BFH-50157 3/8” Nylock Batca Fitness Systems LD-8 Owner's Manual...
- Page 13 Step 6: Figure 6 Item # Part # Description All Flat Washers and Nylocks are BFP-10925 Thigh Pivot Plate 3/8” unless otherwise noted. BFH-50219 1” Shaft Collar www.batcafitness.com LD-8 Owner’s Manual...
-
Page 14: Bfp-51653
SHCS 3/8” x 1 1/4” BFP-51697 SHCS 3/8” x 1 1/2” BFP-51799 SHCS 3/8” x 5” All Flat Washers and Nylocks are BFH-50147 3/8” Lock Washer 3/8” unless otherwise noted. BFH-50204 3/8” Curved Washer BFH-50157 3/8” Flat Washer Batca Fitness Systems LD-8 Owner's Manual... - Page 15 Step 8: Figure 8 Item # Part # Description BFP-51711 Placard Plate BFP-51740 Rear Weight Stack Shroud BFP-52430 BHSCS 3/8” x 3/4” BFH-50254 HCS 3/8” x 3/4” BFH-50146 3/8” Flat Washer www.batcafitness.com LD-8 Owner’s Manual...
- Page 16 Step 9: Figure 9 Item # Part # Description All Flat Washers and Nylocks are 3/8” unless otherwise noted. BFP-51741 Left Front Shroud BFP-51742 Right Front Shroud Batca Fitness Systems LD-8 Owner's Manual...
- Page 17 Clean guide rods with a lint-free cloth and apply a thin layer of silicone lubricant (Part # BFH- 50262) to each guide rod. This will ensure a glass smooth performance from your weight stack. www.batcafitness.com LD-8 Owner’s Manual...
- Page 18 Note: If the top plate raises off of the second plate in the weight stack, then the cable ten- sion is too tight. You will need to take some of the tension out to lower the Top plate flush with the second plate. Batca Fitness Systems LD-8 Owner's Manual...
- Page 19 Home Clean Upholstery Hand Grips Roller Pads Guide Rods Chrome Slides Frame Inspect Overall Safety Decals Cables Cable Tension Pulleys Hardware Stops Upholstery Hand Grips Frame Bushings Bearings Lubricate Guide Rods As Needed Bearings Replace Cables www.batcafitness.com LD-8 Owner’s Manual...
- Page 20 This warranty applies only to the original purchaser and is not transferable. Claims under this war- ranty must be made directly to Batca Fitness Systems. Batca Fitness Systems 1207 N. New Hope Road Raleigh, NC 27610 (919) 255-1233 www.batcafitness.com Batca Fitness Systems LD-8 Owner's Manual...
- Page 21 Layout Diagram The LD-8 has a layout dimension of 5’-0” (width) x 6’-2” (length) x 5’-0” (height). There should be a minimum of 18”, preferably 24”, of working space around the entire unit. www.batcafitness.com LD-8 Owner’s Manual...
Need help?
Do you have a question about the LD-8 and is the answer not in the manual?
Questions and answers