1. Manuals
  2. Brands
  3. Digital-Ally Manuals
  4. Accessories
  5. DTM-600
  6. Installation manual

Digital-Ally DTM-600 Installation Manual

Hide thumbs Also See for DTM-600:
Table of Contents

Advertisement

Quick Links

Download this manual
DTM-600
Installation Guide
860-00323-00 Rev E pg.1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the DTM-600 and is the answer not in the manual?

Questions and answers

Related Manuals for Digital-Ally DTM-600

Summary of Contents for Digital-Ally DTM-600

  • Page 1 DTM-600 Installation Guide 860-00323-00 Rev E pg.1...

  • Page 2: Table Of Contents

    Contents 1.Overview…………………………..............................3 2. Wiring Diagram ................................. 4 3. Floor Stand Option ................................6 3.1. Floor Stand…………………..............................7 3.2. Temp Sensor Option……............................... 11 3.3. Forehead Temperature Sensor Option ........................18 4. Desktop Stand Option……............................... 24 5. Wall Mount Option………… .............................. 25 6.

  • Page 3: Overview

    1. Overview This document provides assembly instructions for the Floor Stand, Desk Stand, Wall Mount, and Temperature Sensor options for the DTM-600. The wiring diagram for the terminal and temp sensor apply to each of the three mounting options. Floor Stand...

  • Page 4: Wiring Diagram

    Forehead Temp Sensor Orange RS485 P Blue +12vdc Red OR Black with stripe Power Harness Note: The DTM-600 firmware can differentiate between the Wrist Temp Sensor and Forehead Temp Sensor. No additional +12vdc configuration is required. Ethernet Network Jack AC/DC Adapter...
  • Page 5 RS485 P RS485 P Orange Blue +12vdc Red OR Black with stripe Power Harness Note: The DTM-600 firmware can differentiate between the Wrist Temp Sensor and Forehead Temp Sensor. No additional configuration is required. +12vdc Ethernet Network Jack AC/DC Adapter...

  • Page 6: Floor Stand Option

    3. Floor Stand Option The mounting plate packaged with the DTM-600 terminal and the mounting bracket packaged with the Temperature Sensor is mounted to the floor stand. Once the hardware is assembled, reference the wiring diagram to complete the assembly.

  • Page 7: Floor Stand

    3.1. Floor Stand Remove the floor stand from the packaging. For ease of assembly, place the floor stand on the floor or table face down. terminal base adapter back plate back plate back plate Remove the terminal back plate by removing the 2 screws. Remove the adapter back plate from the floor stand by removing the 2 screws.
  • Page 8 Remove the AC adapter plate from the mid-way back plate by removing the 2 screws. Note: bending the AC adapter plate as shown will allow the AC adapter to seat flush. Seat the AC adapter on the adapter plate. Seat the AC adapter plate atop the mid-way back plate and secure in place with 2 screws. 860-00323-00 Rev E pg.8...
  • Page 9 Plug the AC cable into the AC adapter. Remove the back plate at the base of the floor stand. Feed a network cable (not supplied) into the mid-way access cutout to the top and bottom of the floor stand. Orient the AC adapter cables as shown below and carefully reseat the mid-way back plate. 860-00323-00 Rev E pg.9...
  • Page 10 Secure the mid-way back plate in place with 6 screws. Orient the base plate to align the threaded studs to the floor stand. Seat and thread the nuts to the threaded studs. Orient the base back plate to allow the network cable and AC cable through the plate. Secure the base back plate in place with 4 screws.

  • Page 11: Temp Sensor Option

    3.2. Temp Sensor Option Determine what height to mount the temp sensor. Orient the temp sensor mounting bracket and secure in place using the 2 counter sunk screws supplied Orient the temp sensor as shown, feeding the harness through the floor stand. 860-00323-00 Rev E pg.11...
  • Page 12 Seat the temp sensor on the mounting bracket as shown. Secure the temp sensor to the bracket using the 2 pan head screws supplied. Apply the temperature sensor label as shown below. Secure the terminal mounting plate to the floor stand using the 2 bolts and nuts provided. Plug the power harness and I/O harness into the back of the terminal.
  • Page 13 Feed the power and I/O harness through the mounting plate of the floor stand. Seat the terminal on the mounting plate. 860-00323-00 Rev E pg.13...
  • Page 14 Secure the terminal in place by driving the security screw with the supplied allan key. Plug the ethernet cable into the terminal. 860-00323-00 Rev E pg.14...
  • Page 15 Reference the wiring diagram from Section 2 for power, network, and I/O connectivity. Connect the power harness included in the wiring kit to the AC adapter and wrap with electrical tape. 860-00323-00 Rev E pg.15...
  • Page 16 Note: the wiring below makes use of the screw barrier blocks. +12vdc Temp Sensor Power Terminal Power Harness Wiring Kit Power Harness RS485 Temp Sensor Terminal I/O Harness 860-00323-00 Rev E pg.16...
  • Page 17 Secure the terminal back plate in place with the 6 screws. Proceed with the Terminal Configuration in Section 6. 860-00323-00 Rev E pg.17...

  • Page 18: Forehead Temperature Sensor Option

    3.3. Forehead Temperature Sensor Option Use of the extension bracket is recommended to raise the height of the terminal. Align the extension bracket with the floor stand and secure in place with 2 screws from within the floor stand. 860-00323-00 Rev E pg.18...
  • Page 19 The Forehead Temperature Sensor mounting bracket is mounted behind the Terminal mounting bracket. Align the mounting holes of the two brackets as shown below and secure in place with 2 screws and wing nuts. 860-00323-00 Rev E pg.19...
  • Page 20 Seat the terminal on the mounting plate. Secure the terminal in place by driving the security screw with the supplied allan key. 860-00323-00 Rev E pg.20...
  • Page 21 Seat the Forehead Temperature Sensor on the mounting bracket and secure in place with 2 screws. Correct Orientation 860-00323-00 Rev E pg.21...
  • Page 22 Reference the wiring diagram from Section 2 for power, network, and I/O connectivity. Connect the power harness included in the wiring kit to the AC adapter and wrap with electrical tape. The Forehead Temperature Sensor is wired in the same manner as the Wrist Temperature Sensor on page 15-16. 860-00323-00 Rev E pg.22...
  • Page 23 Align and slide the Back Cover over the Extension Plate until it is fully seated. 860-00323-00 Rev E pg.23...

  • Page 24: Desktop Stand Option

    4. Desktop Stand Option The desktop mount allows for direct mounting of the DTM-600 terminal and Temperature Sensor. Mount the temperature sensor and secure in place using the 2 pan heads screws supplied with the sensor. The temp sensor harness should be run down and behind the main plate as shown above.

  • Page 25: Wall Mount Option

    5. Wall Mount Option The mounting plate packaged with the DTM-600 terminal allows for direct mounting to the wall. The mounting bracket packaged with the Temperature Sensor allows for direct mounting to the wall. The wall mounting bracket option for the Temperature Sensor allows for an extending mounting option when mounting to the wall.
  • Page 26 Example surface mount option Electrical Terminal Mounting Plate Connector #0 EMT Hanger NM Clamp Connector Temp Sensor Cable Feed-Thru 1/2” EMT #0 Conduit Hanger EMT to NM Coupling #0 Conduit Hanger +12vdc Ethernet Feed-Thru 860-00323-00 Rev E pg.26...

  • Page 27: Terminal Configuration

    6. Terminal Configuration 6.1. Device Startup and Login Apply power to the DTM-600 by plugging in the AC adapter. The device screen and LEDs will light up, indicating that the device is started successfully, and the boot process has begun.

  • Page 28: Osd Configuration

    6.2. OSD Configuration Log-In Press and hold the display screen for approximately 3 seconds. Enter the password and press OK to continue. Press the Authentication scene icon to continue. 860-00323-00 Rev E pg.28...
  • Page 29 Configure the Temperature Range (no change recommended). Configure the Temperature Alarm Threshold (recommend a value of 99.6). Mask Detection Enable or the Disable the DTM-600 to alert the user to wear a mask. Authentication Scene Three Authentication Scene options: Temperature Measurement Only...

  • Page 30: Web Portal Configuration

    6.3. Web Portal Configuration Viewing the OSD, note the IP Address at the bottom left hand corner. Open a browser and type the IP address of the device in the URL bar. Press enter to continue. Note: Internet Explorer is the preferred browser for use with the Web Portal Type the username and password to continue.
  • Page 31 Authentication Failed and Open the Door (OFF by default – reference user guide for details) Configure the Temperature Alert option (OFF by default – reference user guide for details) Mask Detection Enable or the Disable the DTM-600 to alert the user to wear a mask. 860-00323-00 Rev E pg.31...
  • Page 32 Check Template The Check Template is another Authentication option available through the Web Portal. Authentication can be configured with the following options: Note: the mask (if enabled) and temperature options are included by default with the Card and Face options Card this option requires a badge (added to the Face Library) for authentication (includes mask (if enabled) and temperature authentication)

  • Page 33: Contact Information

    7. Contact Information 15612 College Blvd Lenexa, KS 66219 Web: www.digitalallyinc.com E-mail: info@digitalallyinc.com Phone: 913.814.7774 Fax: 913.814.7775 Customer Portal: www.digitalallyinc.com/login.cfm Support E-mail: support@digitalallyinc.com Sales E-mail: sales@digitalallyinc.com Sales / Support Toll Free: 1.800.440.4947 (8am - 5pm CST) 860-00323-00 Rev E pg.33...

Table of Contents