Amperes iPX5101 Instruction Manual

Amperes iPX5101 Instruction Manual

Ethernet paging server
Hide thumbs Also See for iPX5101:

Advertisement

Quick Links

INSTRUCTION MANUAL
iPX5101
Ethernet Paging Server
iPX 5101
amperes
ACT STATUS
REM
POWER
ETHERNET PAGING SERVER
Thank you
for choosing another quality product from Amperes Electronics.
iPX5101 has been upgraded further with newer technology in keeping pace with the demands of today's PA complexity.
Among them is the Ultra Low Latency audio and data transmissions.
It functions as a traffic controller for all paging clients ( iPX5151 / iPX5155 / iEP1202 ). Every activity from Clients shall be
monitored by iPX5101 and would determine the intended routing to be allowed or otherwise, considering the priority level,
traffic condition and the zone configuration.
With the growing demand of IP Paging System, Amperes IP related products such as iPX5101 shall be the great tool for
coming future. Do read through the manual in order the tap the many advantages that Amperes IP system has to offer.
Applicable for Version 2.29 and above
VER 4/ 2021

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the iPX5101 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Amperes iPX5101

  • Page 1 With the growing demand of IP Paging System, Amperes IP related products such as iPX5101 shall be the great tool for coming future. Do read through the manual in order the tap the many advantages that Amperes IP system has to offer.
  • Page 2: Parts Identification

    Bootloader mode: To enter this mode, hold the reset button untl POWER, REM and STATUS LEDs lit. Enter this mode to do update firmware if normal mode updating via web browser does not work. All iPX5101 settings remain intact in this mode.
  • Page 3: Schematic Diagram

    Music / Paging Audio Data SUB RACK Note: In a system, only one iPX5101 is required, no matter what the size of the system or the number of clients ( iPX5151 or iPX5155 ) are installed. iPX5101 | ETHERNET PAGING SERVER PAGE 3...
  • Page 4: Connecting The Unit

    Single / MM Fiber Optic cable To System ( Local Rack ) Audio to pre-amp Data to zone decoder To Sub System Note: Connection to sub rack can be done using existing LAN PAGE 4 iPX5101 | ETHERNET PAGING SERVER...
  • Page 5 PLIFIER MIXER ZONE DECODER POWER AMPLIFIERS ETC. Paging / Music / Siren Data iPX5101 can work with PMX LAN to allow a user to conduct paging, music playing or initiate a siren from a PC. iPX5101 | ETHERNET PAGING SERVER PAGE 5...
  • Page 6 Device Setup Via Browser iPX5101 shall require some setups via web browser. Kindly follow instructions listed below. Open a browser (Chrome / IE) and enter iPX5101 IP address. The default address is 192.168.0.100. Default username and password are both “admin”.
  • Page 7 E.g. if Mic 1 is paging zone 1 & 2; Mic 2 is paging zone 2 & 3 then zone 2 is an overlapped zone. Device Name BLK A Paging Server Concurrent Paging Enter new username Enter new password iPX5101 | ETHERNET PAGING SERVER PAGE 7...
  • Page 8 2.17 Connected 5155 (Sub 2) 192.168.0.156 iPX5155 2.29 Connected 4 - 6 5155 (Sub 4) 192.168.0.157 iPX5155 2.29 Connected 7 - 9 Time 10:00:05 [Socket:4] Timeout 10:00:03 Connected to SSE Socket: 5 PAGE 8 iPX5101 | ETHERNET PAGING SERVER...
  • Page 9: Firmware Update

    Update firmware in Normal Operation Mode 1. Open a browser and type in the iPX5101 IP address. 2. Under “System Configuration” page look for “Firmware Update” section as shown in below. Click “SELECT FIRMWARE” and choose a binary file with “.acfr” extension.
  • Page 10 Update firmware in Bootloader Mode If the iPX5101 “hanged”, it is required to perform system reset by : 1. Press & hold the reset button until “STATUS” LED is turned ON. This will set the IP address to default address 192.168.0.100.
  • Page 11: Paging Operation

    Same Priority Override (SPO) - Enable this setting to allow same priority level paging mics to override each other whenever they are calling to the same zone range or overlapped zone range. This setting is configured in iPX5101. Auto Override Low Priority (AOLP) - Enable this setting allow a high priority paging mic to override lower priority mic or same priority mic (if SPO is enabled).
  • Page 12 Scenario 1: iPX5101 allow same priority override. Since both mics have the same priority and their AOLP are set to On, when both mics are calling the same zone, the late caller (Mic-B) shall override Mic-A and be the one finally active in paging.
  • Page 13 Scenario 6: In this case both Mic-A and Mic-B are calling different zones. The system has two units of iPX5155 (iPX5155-C & D)and both unit has an overlapped zone (zone 2). When Mic-B call to zone 2 it will override Mic-A (due to iPX5101 enable SPO) and page to both iPX5155-C & D. Paging status when Mic-B call...
  • Page 14 Paging Operation Scenario 8: In this case iPX5101 Concurrent Paging is set to 2 hence only two mics are allowed to talk concurrently. When Mic-E call to zone 3, it shall override the oldest active paging which in this case is the Mic-A.
  • Page 15: Technical Specification

    Case : Dimension 482 x 44 x 180 mm Weight 1.9 kg Note: The above specifications are correct at time of printing but subjected to changes without prior notice due to product improvements. PAGE 15 iPX5101 | ETHERNET PAGING SERVER...
  • Page 16: Warranty Conditions

    Information contained in this manual is subject to change without prior notice and does not represent a commitment on the part of the vendor. AMPERES ELECTRONICS SDN BHD shall not be liable for any loss or damages whatsoever arising from the use of information or any error contained in this manual.

Table of Contents