Moog Videolarm PB24FM-SC Installation And Operation Instruction Manual

Power box with ethernet over fiber converter

Advertisement

Quick Links

© 2009, Videolarm, Inc. All Rights Reserved
PB24FM-SC
Power Box with Ethernet over Fiber Converter
Installation and Operation Instructions for the following models:
PB24FM-SC
Rugged cast aluminum power box with 220/115 Vac input
converting to 24Vac and 96W output power. Includes Ethernet
over Fiber converter (EOF2N)
Before attempting to connect or operate this product,
please read these instructions completely.
© 2009, Videolarm, Inc. All Rights Reserved
www.videolarm.com
CERTIFIED
81-IN5432
04-07-2009

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the PB24FM-SC and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Moog Videolarm PB24FM-SC

  • Page 1 © 2009, Videolarm, Inc. All Rights Reserved PB24FM-SC © 2009, Videolarm, Inc. All Rights Reserved Power Box with Ethernet over Fiber Converter www.videolarm.com Installation and Operation Instructions for the following models: PB24FM-SC Rugged cast aluminum power box with 220/115 Vac input converting to 24Vac and 96W output power.
  • Page 2 IMPORTANT SAFEGUARDS SAFETY PRECAUTIONS Read these instructions. Keep these instructions. CAUTION Heed all warnings RISK OF ELECTRIC SHOCK DO NOT OPEN Follow all instructions. Do not use this apparatus near water. CAUTION: TO REDUCE THE RISK OF Clean only with damp cloth. ELECTRIC SHOCK, DO NOT REMOVE Do not block any of the ventilation openings.
  • Page 3 LIMITED WARRANTY FOR VIDEOLARM INC. PRODUCTS VIDEOLARM INC. warrants this Product to be free from defects in material or workmanship,as follows: PRODUCTCATEGORY PARTS LABOR All Enclosures and Electronics Five (5) Years Five (5) Years Pan/Tilts Three (3) Years **6 months if used in autoscan Three (3) Years **6 months if used in autoscan /tour operation /tour operation...
  • Page 4 Electrical Specifications Contents of Box PB24FM-SC Input Power: 110 VAC/220VAC 1A/.5A Power Consumption: 1Amp (120 Watts) at 120 VAC Power Output: 96 VA at 24 VAC 52 Watts Heater/Blower 32 Watts Camera Power English An all pole main switch with a contact of at least 3mm in each pole shall be incorporated in the electrical installation of the building.
  • Page 5 Wall Mounting: Attach unit securely with (4) The power box may be pole mounted with 3/8” or 8mm hardware (not supplied). the pole support clips. • La pared que monta la caja de la energía es posible, • Ésta es la plantilla del montaje para la caja de la pero el hardware no es incluido.
  • Page 6 INPUT: (120VAC or 240VAC) 220-240VAC INPUT 110-120VAC INPUT 240Vac 120Vac Input Main Input Switch Line (L) and Neutral (N) wires should be connected as marked on the board and plugged into the corresponding voltage for the input single phase. Los alambres de la línea (l) y del hilo neutro (n) se deben conectar según lo marcados en el tablero y tapa- dos en el voltaje correspondiente para la monofásico de la entrada.
  • Page 7 RP4OHGPB1000 RP70TRAN11 RP76PCBPB01 RPVL2781 RP96GK2680...
  • Page 8 Ethernet Over Fiber Converter (EOF2N) Remove fiber converter from the power box. Connect fiber lines and RJ45 network cable to the fiber converter. Network...
  • Page 9: Electrostatic Discharge (Esd)

    Electrostatic Discharge (ESD) Always observe the following ESD precautions when installing or handing the EOF2N media converter: • Do not remove the converter from its protective packaging until you are ready to install it. • Wear an ESD wrist grounding strap before handling any module or component. If you do not have a wrist strap, maintain grounded contct with the system unit throughout any procedure requiring ESD protection.
  • Page 10: Connect The Fiber Cable

    Connect the fiber cable Full dupex (always ON) is on the fiber side only; therefore, the 512-Bit Rule does not apply. The cable lengths are constrained by the cable requirement. 1. Locate or build IEEE 803.2™ compliant 100Base-FX fiber cable with male, two-stranded TX to RX connectors installed at both ends.
  • Page 11: Product Features

    Status LEDs Use the LEDs to monitor the status of the media converter. LED discriptions are as follows: TX-Link/Act LED FX-Link/Act LED Green ON = Link (fiber) FX-Link/Act LED Flashing = Activity TX -Link/Act LED Green = Link Flashing = Activity Power LED Fiber Port Green...
  • Page 12 Product features Automatic link restoration The media converter will automatically re-establish the link when connected to switches if the link is lost, even with Auto- Negotiation and Link Pass-through ( both directions) enabled. Full-Duplex flow control In a full-duplex network, the maximum cable lengths are determined by the type of cables used for EOF2N cable specifications.
  • Page 13 Cable Specifiactions The physical characteristics must meet or exceed IEEE 802.3™ specifications. Fiber cable Bite Error Rate: <10-9 single mode fiber (recommended): 9 µm Multimode fiber (recommended): 62.5/125 µm Multimode fiber (optional): 100/140, 85/140, 50/125 µm EOF2N EOF2N 1300 nm multimode Fiber-Optic Transmitter Power: min: -19.0 dBm max: - 14.0 dBm Fiber-Optic Receiver Sensitivity:...
  • Page 15: Product Registration/Warranty

    Product Registration/Warranty Thank you for choosing Videolarm. We value your patronage and are solely committed to providing you with only the highest quality products available with unmatched customer service levels that are second-to-none in the security industry. Should a problem arise, rest assure that Videolarm stands behind its products by offering some of the most impressive warranty plans available: 3 Years on all Housings, Poles, Power Supplies, and Accessories and 5 Years on all camera systems (SView, QView, Warriors), and InfraRed Illuminators.

Table of Contents