Table of Contents
Advertisement
Quick Links
Operating instructions TSM-21
Operating instructions
TSM-21 hopper call-up control
for belt hoppers of type BB / BZS
Art. no.: 90.0010.60
fimotec-fischer GmbH & Co. KG
Friedhofstraße 13
D -78588 Denkingen
Tel:
+49 (0)74 24 - 88 4-0
Fax:
+49 (0)74 24 - 88 4-50
E-mail:
post@fimotec.de
Internet:
www.fimotec.de
Status as of 12 / 2021
Page 1
Advertisement
Table of Contents
Related Manuals for FM TSM-21
Summary of Contents for FM TSM-21
- Page 1 Operating instructions TSM-21 Operating instructions TSM-21 hopper call-up control for belt hoppers of type BB / BZS Art. no.: 90.0010.60 fimotec-fischer GmbH & Co. KG Friedhofstraße 13 D -78588 Denkingen Tel: +49 (0)74 24 - 88 4-0 Fax: +49 (0)74 24 - 88 4-50 E-mail: post@fimotec.de...
- Page 2 Operating instructions TSM-21 In your own interest: Please read these instructions and keep them in a safe place. Please observe and follow the safety information. Contact fimotec-fischer GmbH & Co. KG Friedhofstr. 13 D -78588 Denkingen Tel.: +49 7424 884 0...
-
Page 3: Table Of Contents
Operating instructions TSM-21 Table of contents 1 General The product Guide for these instructions Safety-related information for the user Intended use 2 Installation Overview and dimensions Connections / operating elements of boards Housing connections 3 Commissioning Hopper belt operation Hopper filling level check operation... -
Page 4: General
TSM-21 device. In addition, you will find information as well as important warnings for your safety. Please observe: Devices of the TSM-21 series are specially adapted motor controls for actuating hopper systems with 230 V AC capacitor motors. The product ... -
Page 5: Safety-Related Information For The User
Operating instructions TSM-21 Safety-related information for the user These instructions contain the required information for the intended use of the device described herein. They are directed toward technically qualified personnel. Qualified personnel are people who have been authorized by persons responsible for the safety of the... -
Page 6: Intended Use
Operating instructions TSM-21 Operation The control device only functions correctly when it is correctly installed and operated. In the event of malfunctions or unclear operating states, you should check the device and remedy the malfunction (see "Error list" chapter) or have them remedied. -
Page 7: Installation
Operating instructions TSM-21 Installation There are 4 bores available for fastening the device on the bottom section of the housing. These are separated from the housing interior. Loosen the cover fastening screws Remove the cover Insert fastening screws in the channel and use these to fasten the device to a vibration-free surface. -
Page 8: Overview And Dimensions
Operating instructions TSM-21 Overview and dimensions Reset button - Acknowledge malfunction Mains switch illuminated X24 - Filling level sensor + workpiece shortage X21 - Controller disable Mains feed Load output with Hirschmann plug GDM 3016 X22 - Level sensor + malfunction message... -
Page 9: Connections / Operating Elements Of Boards
Operating instructions TSM-21 Connections / operating elements of boards Terminal 1 X11 Terminal 2 X11 Terminal 3 X11 N condenser Terminal 4 X11 Terminal 5 X21 +24 V= Terminal 6 X21 Controller disable Terminal 7 ... -
Page 10: Housing Connections
Operating instructions TSM-21 Housing connections Mains feed connection Pin 1 - L Pin 2 - N - Protective conductor Load output connection Pin 1 - N Pin 2 - L Pin 3 - N capacitor - PE Malfunction message/level sensor connection... -
Page 11: Commissioning
Operating instructions TSM-21 Commissioning Before connecting the motor control, the mains voltage and frequency must be determined. If the mains voltage and mains frequency are correct, they can be connected to. The device is set via DIP switches and trimmers. These are inside of the housing. - Page 12 Operating instructions TSM-21 Malfunction Trimmer P5 malfunction Switch-on delay, malfunction 35..180 s Switch-on delay Trimmer P4 belt Switch-on delay, sensor input signal (level sensor) 0..45 s Drive pause Trimmer P3 pause Pause drive (clock mode) 0.5..15s Drive runs continuously: The level sensor does not detect a workpiece in the subsequent machine and switches the drive on after the time t has elapsed.
-
Page 13: Hopper Filling Level Check Operation
Operating instructions TSM-21 Hopper filling level check operation General: The filling level in the hopper can be monitored with the filling level check. Setting via Function Description Direction of rotation DIP 4 ON - Drive direction of rotation counterclockwise DIP 4 OFF - Drive direction of rotation clockwise Sensor input DIP 5 ON - Sensor input signal N.C. -
Page 14: Technical Data
Operating instructions TSM-21 Technical data Mains connection 95 - 253 V~ Mains frequency 50 Hz / 60 Hz Output current, load 3 A~ max. Output voltage, load 230 V~ Protection class IP 54 (except for mains switch) Fuse, load 3.15 A T... -
Page 15: Maintenance And Cleaning
Information about where you can find disposal points for your old devices can be obtained from your city administration or local waste disposal facility. CE conformity The motor control device TSM-21 is marked with the CE marking and therefore meets the relevant European directives. The company fimotec-fischer GmbH & Co. KG herewith confirms that this device complies with the following directives: EN 61000-6-3 and EN 61000-6-2 according to EU directive 2014/30/EU "Electromagnetic compatibility"... -
Page 16: Accessories (Not Included In The Scope Of Delivery)
Operating instructions TSM-21 Accessories (not included in the scope of delivery) Designation Article number Connection cable Filling level M8-3p, 3m straight St. M12 FFM_91.4214.00 Connection cable Filling level M8-3p, 3m angled St. M12 FFM_91.4214.01 Connection cable Filling level M8-3p, 5m straight St. M12 FFM_91.4214.02...