Page 1
User’s Guide L1954T/L1954TQ ake sure to read the Important Precautions before using the product. Keep the User's Guide(CD) in an accessible place for future reference. ee the label attached on the product and give the information to your dealer when you ask for service.
Important Precautions This unit has been engineered and manufactured to ensure your personal safety, however improper use may result in potential electrical shock or fire hazards. In order to allow the proper operation of all safeguards incorporated in this display, observe the following basic rules for its installation, use, and servicing.
Page 3
Important Precautions On Installation Do not allow anything to rest upon or roll over the power cord, and do not place the display where the power cord is subject to damage. Do not use this display near water such as near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool.
Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Connecting the stand Place the monitor with its front facing downward on a soft cloth. Assemble the Stand Body into the product in the correct direction as shown in the picture.
Connecting the Display Disassembling the stand Put a cushion or soft cloth on a flat surface. Slide the Cable Deco Cover out from the stand body. Nip Latch inside, Take off the stand base from stand body. Please pull the stand body lightly to separate it from the hinge body. Place the monitor face down on the cushion or soft cloth.
Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Positioning your display Adjust the position of the panel in various ways for maximum comfort. Tilt Range: -5˚~20˚...
Connecting the Display Using the Computer Make sure to turn off the computer and product. Connect the cable as below sketch map form Connect DVI Cable Connect Dsub Cable (PC) Connect Dsub Cable (Mac) Power Cord Analog signal D-sub Insert the Cable Deco Cover in the Stand Body in the correct direction. Press button on the front switch panel to turn the power on.
Control Panel Functions Front Panel Controls The resolutions at which the EZ ZOOMING operates are as follows: 1280 x 1024, 1024 x 768, 800 x 600 The setting method can differ by O/S or video card. In this case, Please ask to the computer or the video card manufacturer.
Page 9
Control Panel Functions Buttons AUTO/SET Button Power Button Power Indicator Use these buttons to select or adjust functions in the On Screen Display. For more information, refer to page A14. Use this button to make D-Sub or DVI connector active. This feature is used when two computers are connected to the display.
On Screen Display (OSD) Control Adjustment Screen Adjustment Making adjustments to the image size, position and operating parameters of the display is quick and easy with the On Screen Display Control system. A short example is given below to familiarize you with the use of the controls. The following section is an outline of the available adjustments and selections you can make using the OSD.
Page 11
On Screen Display(OSD) Selection and Adjustment The following table indicates all the On Screen Display control, adjustment, and setting menus. Main menu Sub-menu BRIGHTNESS PICTURE CONTRAST GAMMA COLOR PRESET GREEN BLUE HORIZONTAL POSITION VERTICAL CLOCK PHASE TRACKING SHARPNESS LANGUAGE SETUP POSITION VERTICAL WHITE BALANCE POWER INDICATOR...
On Screen Display(OSD) Selection and Adjustment You were introduced to the procedure of selecting and adjusting an item using the OSD system. Listed below are the icons, icon names, and icon descriptions of the all items shown on the Menu. Press the MENU Button, then the main menu of the OSD appears.
Page 13
On Screen Display(OSD) Selection and Adjustment Main menu PICTURE P I C T U R E MENU : Exit : Decrease : Increase SET : Select another sub-menu COLOR C O L O R MENU : Exit : Decrease : Increase SET : Select another sub-menu POSITION P O S I T I O N...
Page 14
On Screen Display(OSD) Selection and Adjustment Main menu TRACKING T R A C K I N G MENU : Exit : Decrease : Increase SET : Select another sub-menu SETUP S E T U P S E T U P MENU : Exit : Adjust : Adjust...
On Screen Display(OSD) Selection and Adjustment The OSD screen will appear when you touch the monitor. Menu Name Icons Sub-menu Name FLATRON F-ENGINE When you execute F-ENGINE, two tones will appear on the screen as shown. The applied screen will appear on the left side, whereas the non-applied screen will appear on the right side.Touch the SET button to use the adjusted screen.
Troubleshooting Check the following before calling for service. No image appears No image appears ● Is the power cord of the display connected? ● Is the power indicator light on? ● Is the power on and the power indicator blue or green? ●...
Troubleshooting Display image is incorrect ● Display Position is incorrect. ● On the screen background, vertical bars or stripes are visible. ● Any horizontal noise appearing in any image or characters are not clearly portrayed. ● The screen color is mono or abnormal.
Troubleshooting Have you installed the display driver? ● Have you installed the display driver? ● Do you see an "Unrecognized monitor, Plug&Play (VESA DDC) monitor found" message? • Be sure to install the display driver from the display driver CD (or diskette) that comes with your display.
Specifications Preset Modes (Resolution) Display Modes (Resolution) 640 x 350 720 x 400 640 x 480 VESA 640 x 480 VESA 800 x 600 VESA 800 x 600 832 x 624 VESA 1024 x 768 VESA 1024 x 768 1152 x 870 VESA 1152 x 900 VESA...
Specifications Signal Connector Pin Assignment DVI-D Connector Signal(DVI-D) T. M. D. S. Data2- T. M. D. S. Data2+ T. M. D. S. Data2/4 Shield T. M. D. S. Data4- T. M. D. S. Data4+ DDC Clock DDC Data Analog Vertical Sync. T.
Installing the Wall mount plate This monitor satisfies the specifications of the Wall mount plate or the interchange device. Place the monitor with its front facing downward on a soft cloth. Separate the stand using a screwdriver as shown in the picture. Install the Wall mount plate.