Related Manuals for Gamma Led Vision TX4 Spot
Summary of Contents for Gamma Led Vision TX4 Spot
- Page 1 TX4 Spot 150w Spot Moving Head User Manual TX4 Spot – GAMMA LED Vision Page 1 of 18...
-
Page 2: Table Of Contents
2. Setup and Operation............................10 Using the LCD Menu and Buttons......................10 Menu Operation...............................10 DMX Setup................................11 DMX Basics..............................11 DMX Wiring..............................11 DMX Modes and Configuration.........................13 3. Maintenance...............................16 Routine Maintenance..........................16 Troubleshooting Problems........................17 4. Technical Specifications..........................18 Photometric Data.............................18 TX4 Spot – GAMMA LED Vision Page 2 of 18... -
Page 3: Introduction And Setup
Introduction and Setup Unpacking and In the Box Thank you for choosing our TX4 Spot moving head light. For your own safety, please read this manual before installing or using the device. This manual covers the important information on installation and applications. Please install and operate the fixture with following instructions. - Page 4 “omega bracket”. As an added safety measure be sure to attached at least one properly rated safety cable to the fixture using on of the safety cable rigging point integrated in the base assembly. TX4 Spot – GAMMA LED Vision Page 4 of 18...
- Page 5 ∙Make sure the lens are in good condition. It’s recommended to replace the units if there are any damages or severe scratches. ∙Make sure the fixture is operated by qualified personnel who know the fixture before using. TX4 Spot – GAMMA LED Vision Page 5 of 18...
- Page 6 Colorful LCD display Efficient low noise fan cooling system PowerCon IN/OUT 3-pin XLR connectors IN/OUT Two 1/4 turn fastening Omega Clamps IP 20 protection rating TX4 Spot – GAMMA LED Vision Page 6 of 18...
-
Page 7: Safety Precautions
If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the manufacturer of his service agent or a similar qualified person in order to avoid a hazard. TX4 Spot – GAMMA LED Vision Page 7 of 18... - Page 8 Don’t expose the fixture in overheating, moisture or environments with too much dust when installing it. And don’t lay any power cables on the floor. Or it might cause electronics shock to the people. TX4 Spot – GAMMA LED Vision Page 8 of 18...
-
Page 9: Customer Support
Customer Support WARRANTY POLICY GAMMA LED Vision warrants its products for the periods set below from the date of purchase to be free of manufacturer and workmanship defects. Warranty does not cover normal wear and tear caused by force, negligence or misuse of products. GAMMA LED Vision is not responsible for any damages or injury caused by misuse or improper handling of the products and in accordance with instructions and specifications of manual. -
Page 10: Setup And Operation
2. Setup and Operation Using the LCD Menu and Buttons Menu Operation TX4 Spot – GAMMA LED Vision Page 10 of 18... -
Page 11: Dmx Setup
DMX Cables can be 3-pin or 5-pin. These use the same type of data, and in the 5-pin only pins 1, 2, and 3 are used. The cable should be a 2 conductor, shielded cable of at least 110 ohms resistance. Microphone cable is not DMX cable. TX4 Spot – GAMMA LED Vision Page 11 of 18... - Page 12 XLR plug with a 120 Ω resistor connected between pins 2 and 3, which is then plugged into the output XLR socket of the last fixture in the chain. Please see illustrations below: TX4 Spot – GAMMA LED Vision Page 12 of 18...
-
Page 13: Dmx Modes And Configuration
DMX Modes and Configuration The TX4 Spot has multiple DMX modes, sometimes called “personalities”, “profiles”, or as we will use here “modes”. In general, modes with more DMX channels offer a greater level of control or options but take up more of your output channels on your lighting console or software. - Page 14 128-191 Gobo Scroll CW, Slow to Fast 192-255 Gobo Scroll CCW, Slow to Fast Gobo Wheel 0-15 Open 2 – Rotating 16-31 Gobo 1 32-47 Gobo 2 48-63 Gobo 3 TX4 Spot – GAMMA LED Vision Page 14 of 18...
- Page 15 Rotate CW slow to fast 136-255 Rotate CCW, slow to fast Automatic Off (no action) Programs 8-131 Automatic Mode 132-255 Sound-active mode Reset 0-249 No function 250-253 Reset 254-255 No function TX4 Spot – GAMMA LED Vision Page 15 of 18...
-
Page 16: Maintenance
There are no serviceable parts inside the device. Please refer to the instructions under “Installation instructions”. Should you need any spare parts, please order genuine parts from your local dealer. TX4 Spot – GAMMA LED Vision Page 16 of 18... -
Page 17: Troubleshooting Problems
Plug the light directly into the DMX controller with a cable that you know is good. Unplug all other lights – does it work? Try to use another DMX controller. TX4 Spot – GAMMA LED Vision Page 17 of 18... -
Page 18: Technical Specifications
Control Signal: DMX 512, master-slave and sound activated or auto operation Control Channel: 16/14/12/10 DMX Channels USITT DMX-512 Power Consumption: 250w Dimensions: 270(D)*270(W)*470(H)mm Packaging Size: 305(D)*305(W)*500(H)mm Net Weight: 11.5kg, Gross Weight 14.0kg Photometric Data TX4 Spot – GAMMA LED Vision Page 18 of 18...