Related Manuals for Media5 Sentinel 400
Summary of Contents for Media5 Sentinel 400
- Page 1 Sentinel Telephony Card Installation Guide For the Sentinel 400 only DGW 48.2.2567 2021-09-21...
-
Page 2: Table Of Contents
Table of Contents Safety Recommendations and Information Danger, Warning, Caution, and Note Definitions Electrical Safety Guidelines General Safety Practices Electrostatic Discharge Prevention Translated Warning Definition Slot Order - IMPORTANT Removing a Telephony Card Installing a New Telephony Card Replacing a Telephony Card Product Disposal Instructions Disclaimers Available Documentation... -
Page 3: Safety Recommendations And Information
Sentinel Telephony Card Installation Guide Safety Recommendations and Information Danger, Warning, Caution, and Note Definitions Danger: Indicates a hazardous situation which, if not avoided, will result in death or serious injury. Warning: Indicates a hazardous situation which, if not avoided, could result in death or serious injury. - Page 4 Sentinel Telephony Card Installation Guide Warning: Disconnect all interface cables (including PRI, BRI, FXS, and FXO) before unplugging any power sources from the Mediatrix unit. Warning: Disconnect all interface cables (including PRI, BRI, FXS, and FXO) as well as all power sources connected to the Mediatrix unit before servicing the unit.
-
Page 5: General Safety Practices
Unit main become very hot in case of fan failure or during intensive use. To avoid any accidental burns, it is important to restrict the physical access to the unit, and to shut it down for 30 minutes before touching it. In case of fan failure, please contact Media5 or your authorised reseller or vendor. -
Page 6: Electrostatic Discharge Prevention
Sentinel Telephony Card Installation Guide • Do not perform any action that creates a potential hazard to people or makes the equipment unsafe. • Do not open or disassemble this product. • The unit should be located at 20 cm from your monitor, computer casing or other peripheral including speakers. - Page 7 Sentinel Telephony Card Installation Guide Warnung: Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu einer Körperverletzung führen könnte. Bevor Sie mit der Arbeit an irgendeinem Gerät beginnen, seien Sie sich der mit elektrischen Stromkreisen verbundenen Gefahren und der Standardpraktiken zur Vermeidung von Unfällen bewußt Avvertenza: Questo simbolo di avvertenza indica un pericolo.
-
Page 8: Slot Order - Important
Sentinel Telephony Card Installation Guide Slot Order - IMPORTANT The order and location the cards are installed is crucial for the unit to work properly. • Slot order is indicated on the front of the unit (left bottom corner) • Always start from slot 1 IMPORTANT: Slot 1 is the only slot having the capabilities of controlling the backplane interfaces. -
Page 9: Removing A Telephony Card
Sentinel Telephony Card Installation Guide Removing a Telephony Card Before you start Warning: When installing or replacing a Telephony Interface Card in the Mediatrix unit, the earth ground connection between the grounding screw on the back of the Mediatrix unit and an appropriate grounding point in your site is mandatory all the time. -
Page 10: Installing A New Telephony Card
Sentinel Telephony Card Installation Guide Disconnect all cables (except the earth ground connection) from the Mediatrix unit. Caution: Power source cables must be disconnected last. Unscrew the two thumb screws of the slot where you wish to remove a card. Gently remove the existing card. - Page 11 Sentinel Telephony Card Installation Guide Warning: This equipment must be installed and maintained by service personnel. Incorrectly connecting this equipment to a general-purpose outlet could be hazardous. IMPORTANT: To comply with the ISED and ACTA regulatory aspects, the label supplied with the telephony card must be applied on the exterior surface of the Model S casing during the installation of the telephony card.
-
Page 12: Replacing A Telephony Card
Sentinel Telephony Card Installation Guide Apply the label indicating the ISED and ACTA registration numbers on the exterior surface of the casing. Replacing a Telephony Card Before you start Warning: When installing or replacing a Telephony Interface Card in the Mediatrix unit, the earth ground connection between the grounding screw on the back of the Mediatrix unit and an appropriate grounding point in your site is mandatory all the time. - Page 13 Sentinel Telephony Card Installation Guide Turn OFF the power sources used to power the Mediatrix unit at the circuit breaker. Disconnect all cables (except the earth ground connection) from the Mediatrix unit. Caution: Power source cables must be disconnected last. Unscrew the two thumb screws of the slot where you wish to change the card.
-
Page 14: Product Disposal Instructions
For appropriate disposal and recycling instructions, contact your local Media5 Corporation provider. The Waste of Electrical and Electronic Equipment (WEEE) Directive (2002/96/EC) was established... -
Page 15: Disclaimers
Directives 2014/30/EC and 2014/35/EC European parliament (EMC and LVD directives)is given. Any unauthorized modification of the product voids this declaration. For a copy of the original signed Declaration Of Conformity please contact Media5 at the above address. RoHS Declaration Of Compliance This Mediatrix unit is in compliance with the Council Directives 2011/65/EC on the restriction of the use of certain hazardous substances in electrical and electronic equipment. -
Page 16: Available Documentation
Sentinel Telephony Card Installation Guide Available Documentation For more details, refer to the published on the Mediatrix Documentation Media5 Documentation Portal media5corp.com... -
Page 17: Copyright Notice
Copyright © 2021 Media5 Corporation. This document contains information that is proprietary to Media5 Corporation. Media5 Corporation reserves all rights to this document as well as to the Intellectual Property of the document and the technology and know-how that it includes and represents.
Need help?
Do you have a question about the Sentinel 400 and is the answer not in the manual?
Questions and answers