Related Manuals for CB ELECTRONICS TMC-1-MMP1
Summary of Contents for CB ELECTRONICS TMC-1-MMP1
- Page 1 TMC1-MMP1 Monitor Controller CB Electronics TMC-1-MMP1 Monitor Remote Use with the TMC-1Reference Provisional 0.0 © 2016 CB Electronics Version 0.0...
-
Page 2: Table Of Contents
TMC1-MMP1 Monitor Controller s ............................2 1 ..........................4 TMC-1-MMP1 User guide....................... 4 Ethernet Connection ........................4 Setting the TMC-1 IP Address from the TMC-1-win/mac program..........5 MMP1 4.1 Implementation ......................6 MMP1 E-Net Pages ........................8 Discovery............................ 8 Network Page: ........................... 8 Socket Debug:........................... - Page 3 TMC1-MMP1 Monitor Controller Talkback Microphone and Headphone ................... 14 Internal Talkback Microphone ....................14 Headphone Jack ........................14 g ........................16 s ..........................17 © 2016 CB Electronics Version 0.0...
-
Page 4: Tmc-1-Mmp1 User Guide
TMC1-MMP1 Monitor Controller TMC-1-MMP1 User guide This document only describes the Ethernet connections of the TMC-1 and any differences in operation. Please refer to the TMC-1 Reference which is available from the main TMC-1 Web Page. http://www.colinbroad.com/cbsoft/tmc1/tmc1.html Ethernet Connection The TMC-1 communicates to the MMP1 via Ethernet, when connected to the network it will discover any connected MMP1’s and display them. -
Page 5: Setting The Tmc-1 Ip Address From The Tmc-1-Win/Mac Program
TMC1-MMP1 Monitor Controller Setting the TMC-1 IP Address from the TMC-1-win/mac program © 2016 CB Electronics Version 0.0... -
Page 6: Mmp1 4.1 Implementation
TMC1-MMP1 Monitor Controller MMP1 4.1 Implementation The TMC-1-MMP1 and MMP1 are both new, not everything is implemented at this time, Yammaha have provided restricted access to the MMP1 functions to the TMC-1. More functions are available in the iPad emulation mode. - Page 7 User keys Snap1 - Snap- Scene Selection User keys Scene1 - Scene5 Cough User keys Cough1 - Cough8 IPad Remote Emulation Advanced Menu 24 - The TMC-1 can switch the TMC-1 to iPad emulation mode © 2016 CB Electronics Version 0.0...
-
Page 8: Mmp1 E-Net Pages
Used to debug systems, You can change the socket number using the [+] or [-] keys. Socket 00 = Discovery and setup Socket 01 = MMP1 Control Socket 02 - Meters Other MMP1 Pages © 2016 CB Electronics Version 0.0... -
Page 9: Cue Sends Page
Talkback routing must be specified on this page Depress the [Select] key to enable the source selection and gain for the selected cue output as shown in the lower picture. © 2016 CB Electronics Version 0.0... - Page 10 TMC1-MMP1 Monitor Controller © 2016 CB Electronics Version 0.0...
-
Page 11: L F E + 1 0
TMC-1. If not then the TMC-1 will use its Dim Setting to adjust the gain of the MMP1. TMC-1 Label MMP1 Label SLS (Studio LS) Cue 1 Cue 1 Cue 2 Cue 2 Cue 3 H/P (Headphones) Cue 4 © 2016 CB Electronics Version 0.0... - Page 12 TMC1-MMP1 Monitor Controller © 2016 CB Electronics Version 0.0...
-
Page 13: T M C - 1 S O F T W A R E U P D A T E
TMC-1-MMP1 or TMC-1-XMon MMP1 Remote App. http://www.colinbroad.com/cbsoft/tmc1/tmc1MMP1.html Note. When upgrading from TMC-1-Xmon to TMC-1-MMP1 an upgrade key must be purchased and the MMP1 Option enabled before the MMP1 software is installed. If you install without enabling the MMP1 Option the TMC-1 will jump directly to the software Installation page. -
Page 14: H D 1 5 C O N N E C T O R ( X M O N )
TMC1-MMP1 Monitor Controller The XMon connector is available on the TMC-1-MMP1 for the following Talkback Microphone and Headphone The TMC-1 provides an analogue Talkback Microphone with preamp and Headphone connection which are connected to the HD15 connector. To use connect to Analogue Inputs and outputs on the MMP1. - Page 15 Midi In - Check Connected in Cable Midi In + Check Connected in Cable RS422 Rx + Normally Connected in Cable RS422 Tx + Normally Connected in Cable Midi Out + Check Connected in Cable © 2016 CB Electronics Version 0.0...
- Page 16 Talkback not working The talkback routing must be specified in the TMC-1 cue sends page. Input Selection Not Working Check that L/B is Not enabled Unexpected L/B, talkback, SLS or Monitor Check Auto-Mute Enable/mute © 2016 CB Electronics Version 0.0...
- Page 17 TMC1-MMP1 Monitor Controller CB Electronics has made every effort to ensure the accuracy of information contained within this document, which is nevertheless supplied for information purposes only and does not constitute any form of warranty or guarantee. All trademarks acknowledged.
Need help?
Do you have a question about the TMC-1-MMP1 and is the answer not in the manual?
Questions and answers