Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Troubleshooting
Subscribe to Our Youtube Channel
Related Manuals for Senco ISANTA SIDAF80
Summary of Contents for Senco ISANTA SIDAF80
- Page 1 Automatic Feeding System SIDAF80 Operating Instructions (Original Instructions) KYOCERA SENCO Netherlands B.V. Pascallaan 88 8218 NJ Lelystad, The Netherlands +31 320 295 575 senco.com EMEA: senco.eu NFE2DT2032020 © 2020 by KYOCERA SENCO Netherlands B.V.
- Page 2 Read the operating instructions before use. Only for EU countries Disposal of electric tools together with household waste is not permissible! In observance of European Directive on waste electrical and electronic equipment and its implementation in accordance with national law, electric tools that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility.
-
Page 3: Table Of Contents
1.WARNING AND CAUTION 【1】 Safety Notice for Electric Tools 【2】 Notes for Usage of the Automatic Feeding System SIDAF80 【3】 Notes for Usage of the Reinforced Sensor Mode of Automatic Feeding System SIDAF80 2.DESCRIPTION 3.SPECIFICATIONS 4.CONTROL PANEL 【1】 Name of Each Part of Control Panel 【2】... -
Page 4: Warning And Caution
1. WARNING AND CAUTION To avoid the accidents such as fire, electric shock and personally injury, make sure to follow all instruction ● “Safety notice for electric tools” and “Notes for usage of the Automatic Feeding System SIDAF80” and “Notes for usage of the reinforced sensor mode of Automatic Feeding System SIDAF80”. Before using, please read “WARNING &... - Page 5 When you use the accessories and the options which are not listed in the manual, it might cause the acci- ● dents or personal injury. Please do not use the accessories and the options which SENCO does not rec- ommend.
-
Page 6: 2】 Notes For Usage Of The Automatic Feeding System Sidaf80
【2】 Notes for Usage of the Automatic Feeding System SIDAF80 WARNING 1. Regarding how to use the Core Drill and notes for usage, read the instruction manual of the Core Dill carefully until you understand, then use properly by following the instruction. 2. -
Page 7: 3】 Notes For Usage Of The Reinforced Sensor Mode Of Automatic Feeding System Sidaf80
CAUTION 6. When you set the Core Drill vertically and the clutch is off, be careful that the Drill Head could fall down with sliding due to its own weight. 7. Set the load properly and work efficiently. The proper load of the Drill Motor is different from the condition of cutting object, the size of Core Bit, cut- ●... - Page 8 CAUTION 1. When interference against drilled core generates during the operation, it will be possible to stop even though the Core Bit does not hit to the reinforced steel. Fix the pole base firmly and adjust the Drill Carriage properly, then start to cut carefully. Cut by manual ●...
-
Page 9: Description
2.DESCRIPTION Control Panel Hook Grip Engagement with the Drill Head Positioning Pin CEE17 Plug CEE17 Connector (Cord 0.3m) ((Plug for the Drill Head)) (Cord 2m) Eye Nut 3.SPECIFICATION Power Supply Single-phase A.C.230V 50Hz Max. Power Consumption 52.8W Maximum Rotating Speed of Out- 2.0min put Shaft SPF Core Drill E type... -
Page 10: Control Panel
4. CONTROL PANEL 【１】 Name of Each Part of Control Panel Digital Display When you plug the power supply code to the power supply, ｢Normal Mode｣ displays ｢CC｣and ｢Reinforced Sensor Mode｣ displays ｢FC｣ The load setting and the load current value of the Core Drill display during drilling. over When the drill motor stops with -load or the drill and the feeding are ON and the... -
Page 11: 2】 Changing For ｢Cc : Normal Mode｣ And ｢Fc : Reinforced Sensor Mode
【2】 Changing for ｢CC : Normal Mode｣ and ｢FC : Reinforced Sensor Mode｣ You can change ｢CC: Normal Mode｣ and ｢FC: Reinforced Sensor Mode｣ by controlling the button. ｢Normal Mode｣is to cut the reinforced concrete etc, and ｢Reinforced Sensor Mode｣ is not to cut the reinforced steel in the reinforced concrete. -
Page 12: 3】 Display Pattern When The Operation Stops
Displayed ing two seconds. FE flashing. Stopped by 「Over- load Protection of Feeding Motor」 Light 「Stopped by SENCO Stopper」 Press the feeding button. If the automatic stop is set, it lights. The automatic stop lamp flashes. Automatic stop Light Press the automatic stop setting button. -
Page 13: Standard Accessories
5. STANDARD ACCESSORIES Instruction Manual ・ ・ ・ １ 6. APPLICATIONS Automatic drilling by installing to SENCO Core Drill (E type). ● SIDAF80 can be used only for the Drill Head which is an auto- matic feeding type (E type). -
Page 14: How To Use
8. HOW TO USE CAUTION Regarding the usage of the Core Drill, read each instruction manual of the Core Drill. 【１】 Preparation of the Core Drill Prepare for CEE 17 Plug and CEE 17 Connector in order to connect SIDAF80 and E type Core Drill, ●... -
Page 15: 3】 Wiring
3) Rotate to clockwise until SIDAF80 and the hook of the Drill Carriage of Drill Head engage with pulling the eye nut. Make sure that each of the hook engages and the positioning pin is in the hole of gear cover. WARNING If the positioning pin is not fixed properly, it will be extremely dangerous that SIDAF80 could come... -
Page 16: 4】 Setting For Drilling Depth
(option) to the pole before inserting the Drill Head to the pole. Set the SENCO stopper where your requested drilling depth (A size) is positioned. When the Drill Head is down to the SENCO stopper, the Drill Motor and the feeding motor stop automatically. CAUTION SENCO stopper 1. - Page 17 7) Press the clutch button, and engage the clutch. 8) Press the feeding button. ……the feeding lamp lights, and the feeding operation (drilling) starts. 9) Set the load of the Drill Motor. Press the button once and display makes flashed. (numerical value is not changed at this time.) Press the the button once again, the load setting can be changed from 7A...
-
Page 18: 6】 Drilling With Reinforced Sensor Mode
11) After completing the drilling. ➀ In case of setting the automatic stop The automatic stop operates when penetrating through or reaching to the SENCO stopper. ……Feeding motor and Drill Motor stop, and the automatic stop lamp will flash. Press the automatic stop button and release the automatic stop (flashing of the lamp). -
Page 19: 7】 After The Operation
【 】 ｢ 2) Follow Drilling with Normal Mode｣1) ͠ 9)in the page 14•15, and operate the drilling. When you start to drill and the Core Bit hits to the reinforced steel, the Feeding motor and the Drill Motor stop. And, ｢FC｣and all lamp on the digital display flash. -
Page 20: Trouble Shooting During The Operation
9.TROUBLE SHOOTING DURING THE OPERATION 【１】 Trouble Shooting with Normal Mode During the Operation When you feel the abnormal during the operation, turn off the switch immediately and investigate the caus- ● es under the safe condition following the below table. The trouble shooting here is mentioned that the trouble with the normal mode of the SIDAF80. - Page 21 Panel display Cause Countermeasure Trouble ｢ ｣ The picture shows the digital display but setting current value is displayed. Release flashing by pressing ・ When cutting object is soft. the automatic stop setting ・ When cutting is well due to button, and release the auto- applying the thin bit.
-
Page 22: 2】 Trouble Shooting With Reinforced Sensor Mode During The Operation
【２】 Trouble Shooting with Reinforced Sensor Mode During the Operation When you feel the abnormal during the operation, turn off the switch immediately and investigate the ● causes under the safe condition following the below table. The trouble shooting here is mentioned that the trouble with the reinforced sensor mode of the SI- DAF80. -
Page 23: Maintenance And Inspection
● 13. WARRANTY We will guarantee the SENCO Automatic Feeding System SIDAF80 for 6 months from the data of delivery. During this period we will warranty material and production defects free of charge. We are not responsible for any other damage direct nor indirect other than this. This warranty does not cover normal wear and tear, overloading, non-compliance with the operating instructions and intervention by unauthorized persons or the use of parts from other companies. -
Page 24: Ce Declaration Of Conformity
Poste : Directeur de l'ingénierie Cargo: Director de Ingeniería Posizione: Responsabile di progettazione Lieu du document: KYOCERA SENCO Industrial Tools , Inc. Procedencia de los documentos:KYOCERA SENCO Luogo di emissione: KYOCERA SENCO Industrial Tools, Inc. 4270 Ivy Pointe Blvd. 4270 Ivy Pointe Blvd. - Page 25 Poste : Directeur de l'ingénierie Cargo: Director de Ingeniería Posizione: Responsabile di progettazione Lieu du document: KYOCERA SENCO Industrial Tools , Inc. Procedencia de los documentos:KYOCERA SENCO Luogo di emissione: KYOCERA SENCO Industrial Tools, Inc. 4270 Ivy Pointe Blvd. 4270 Ivy Pointe Blvd.
Need help?
Do you have a question about the ISANTA SIDAF80 and is the answer not in the manual?
Questions and answers