DMP Electronics SR3 Quick Start Manual

SR3 Bluetooth and Proximity Reader
GET STARTED
Quick Start Guide
GET STARTED
SR3 Bluetooth and Proximity Readers support Mobile Credentials and 125 kHz proximity credentials. The reader comes
SR3 Bluetooth and Proximity Readers support Mobile Credentials and 125 kHz proximity credentials. The reader comes
with two mounting options, mullion or single-gang, and is suitable for indoor or outdoor use. The SR3 uses the Wiegand
with two mounting options, mullion or single-gang, and is suitable for indoor or outdoor use. The SR3 uses the Wiegand
reader protocol to communicate with door controllers or access control modules.
reader protocol to communicate with door controllers or access control modules.

Procedure

Procedure
The installation must follow this procedure:
The installation must follow this procedure:
Step 1 (Technician): Install the reader.
Step 1 (Technician): Install the reader.
Step 2 (Technician): Enroll and associate the reader with a system in Tech APP.
Step 2 (Technician): Enroll and associate the reader with a system in Tech APP.
Step 3 (Administrator): Purchase credentials for a customer in Dealer Admin.
Step 3 (Administrator): Purchase credentials for a customer in Dealer Admin.
Step 4 (Customer): Assign credentials to a user in Virtual Keypad.
Step 4 (Customer): Assign credentials to a user in Virtual Keypad.
Step 5 (End User): Bind a mobile credential to a user's device in Virtual Keypad.
Step 5 (End User): Bind a mobile credential to a user's device in Virtual Keypad.
Step 6 (End User): Use the credential at the SR3 Bluetooth Reader.
Step 6 (End User): Use the credential at the SR3 Bluetooth Reader.
This guide walks you through all 6 steps. This quick start guide walks you through Step 1 and Step 2. For the full installation guide, follow the QR code below.
This guide walks you through all 6 steps.
What's Included
Full Installation Guide
What's Included
To view the full

Wire the Reader

WARNING: Do not press and hold the button on the back of the reader. This procedure clears the unit's memory
and firmware, which renders the device inoperable until it is reconfigured and re-enrolled.
Disconnect power before wiring the reader. After wiring and reconnecting power, the LED turns steady yellow, indicating
Wire the Reader
that the reader is ready for enrollment. Follow these guidelines when wiring the reader: Connections must be made in
accordance with NFPA 70: Do not connect to a receptacle controlled by a switch. Minimum wire gauge is 24 AWG with a
Connect the reader wires to the access controller according to the purpose of each controller terminal. Refer
maximum single wire run length of 500 ft (150 m).
to Table 1 and the examples that follow for details. For wiring and power requirements, refer to
Caution: Do not cut the braided directional antenna wire. Wrap it around and secure it to the wiring harness for
future use.
What You'll Need
WIRE COLOR
What You'll Need
▶ Drill
Red
Black
▶ Drill
▶ If mounting with wall anchors, a 5/16" (8.0 mm) drill bit
White
▶ If mounting with wall anchors, a 5/16" (8.0 mm) drill bit
▶ If mounting without wall anchors, a 5/64" (2.0 mm) drill bit
Green
▶ If mounting without wall anchors, a 5/64" (2.0 mm) drill bit
▶ #1 Phillips screwdriver
Blue
▶ #1 Phillips screwdriver
▶ #2 Phillips screwdriver
Orange
Purple
▶ ▶ Pliers #2 Phillips screwdriver
Yellow
▶ ▶ Wire connectors Pliers
Copper, braided - Do not cut
▶ ▶ Electrical tape Wire connectors
* If connected, the orange wire (beeper) mimics keypad beeping.
▶ Electrical tape
SR3 Installation and Programming Guide | Digital Monitoring Products
SR3 Installation Guide (LT-2505), scan this QR code or visit DMP.com.
PURPOSE
Power (Positive)
Ground (Negative)
Data 1
Data 0
Green LED
Beeper* (optional)
Red LED (optional)
Smart Card Present (optional)
Directional Antenna (optional)
Table 1: Wire Connections
TYPICAL X1 SERIES TYPICAL 734 SERIES
TERMINALS TERMINALS
R1 RED
B1 BLK
W1 WHT
G1 GRN
LC LC
BC RA
None None
None None
None - Do Not Cut None - Do Not Cut
"Wiring and Power".
TYPICAL KEYPAD
WIRES
Red
Black
White
Green/White
None
None
None
None
None - Do Not Cut
1